Sodium development

Hydrazine attacks indiarubber, and cork and, when boiled in aq. soln.) glass is eroded. Hydrazine hydrate and sodium develop much heat, with the expulsion of hydrogen and ammonia. When the liquid cools, a crystalline substance is formed which is soluble in water and alcohol, and which is thought to be sodium hydrazide hydroxide, N2H5ONa. The aq. soln. gives the reactions for hydrazine. T. Weich-selfelder prepared the derivatives ... 

SODIUM DEVELOPER AMS AMONOOXYNAPHTHALENE JS-NAPHTHYL ALCOHOL JJ-NAPHTHYL HYDROXIDE... 

Herbivorous animals deprived of sodium develop a characteristic salt hunger, attributed by Bunge to the disturbing effect of the excess of potassium present in all vegetables. Benedict (1915) has found 0-2 gm. NaCl per diem to represent the minimal requirement of adult man, although this quantity is exceeded ten or twentyfold to allow for loss of the metal by renal excretion. 

Prepared by reduction of 4-nitrophenol or 4-nitrosophenoi. Can be diazotized and used as a first component in azo-dyes. Chief outlet is for sulphur dyes in which it is fused with sodium polysulphides. L/sed as a photographic developer. 

Dissolve a few drops of nitromethane in 10% sodium hydroxide solution. Add a few crystals of sodium nitrite and shake. Now add dilute sulphuric acid drop by drop. A brownish-red coloration develops, but fades again when an excess of acid is added. The sulphuric acid has thus liberated nitrous acid, which has in turn reacted with the nitromethane to give a nitrolic acid, the sodium salt of which is CH3NO2 + ONOH = CH(N02) N0H + HgO reddish-brown in colour, probably owing to mesomeric ions of the type ... 

Dissolve 4 5 ml. of aniline in a mixture of 10 ml. of concentrated hydrochloric acid and 20 ml. of water cool the solution to 5°, and diazotise by the addition of 4 g. of sodium nitrite dissolved in 20 ml, of water, observing the usual precautions given on page 181. Dissolve 7 g. of 2-naphthol in 60 ml. of 10% sodium hydroxide solution contained in a 200 ml. beaker, and cool this solution to 5 by external cooling, aided by the direct addition of about 20-30 g. of crushed ice. Now add the diazotised solution very slowly to the naphthol solution, keeping the latter well stirred meanwhile the mixed solutions immediately develop a deep red colour, and the benzeneazonaphthol should... 

Dissolve 2 g. of anhydrous sodium carbonate in 50 ml. of water contained in a 400 ml. beaker and add 7 g. of finely powdered crystalline sulphanilic acid (2H2O), warming the mixture gently in order to obtain a clear solution. Add a solution of 2 2 g. of sodium nitrite in 10 ml. of water and then cool the mixture in ice-water until the temperature has fallen to 5°. Now add very slowly (drop by drop) with continual stirring a solution of 8 ml. of concentrated hydrochloric acid in 15 ml. of water do not allow the temperature to rise above 10°. When all the acid has been added, allow the solution to stand in ice-water for 15 minutes to ensure complete diazotisation during this period fine crystals of the internal salt separate from the pink solution. Dissolve 4 ml. of dimethylaniline in a mixture of 4 ml. of concentrated hydrochloric acid and 10 ml. of water, cool the solution in ice-water, and add it slowly to the cold well-stirred diazo solution a pale red coloration is developed. Allow the mixture to stand for 5 minutes and then add slowly with stirring aqueous... 

Ltebermann Reaction To 1 minute crystal of sodium nitrite in a clean dry test-tube add 0 5 g. of phenol and heat very gently for about 20 seconds allow to cool and add twice the volume of cone. H2S04. On rotating the tube slowly in order to mix the contents, a deep green or deep blue coloration develops (some times only after i 2 minutes). Dilute cautiously with water the solution turns red. Now add an excess of NaOH solution the green or blue coloration reappears. 

It is advisable to test a small portion of the filtrate for platinum by acidifying with hydrochloric acid and adding a few drops of stannous chloride solution a yellow or brown colour develops according to the quantity of platinum pVesent. The yellow colour is soluble in ether, thus rendering the t t more sensitive. If platinum is found, treat the filtrate with excess of formaldehyde and sodium iQrdroxide solution and heat,- platinum black septarates on standing and may be filtered and worked up with other platinum residues (see Method 3). 

Dissolve 1 g. of the secondary amine in 3-5 ml. of dilute hydrochloric acid or of alcohol (in the latter case, add 1 ml. of concentrated hydrochloric acid). Cool to about 5° and add 4-5 ml. of 10 per cent, sodium nitrite solution, and allow to stand for 5 minutes. Add 10 ml. of water, transfer to a small separatory funnel and extract the oil with about 20 ml. of ether. Wash the ethereal extract successively with water, dilute sodium hydroxide solution and water. Remove the ether on a previously warmed water bath no flames should be present in the vicinity. Apply Liebermann s nitroso reaction to the residual oil or solid thus. Place 1 drop or 0 01-0 02 g. of the nitroso compovmd in a dry test-tube, add 0 05 g. of phenol and warm together for 20 seconds cool, and add 1 ml. of concentrated sulphuric acid. An intense green (or greenish-blue) colouration will be developed, which changes to pale red upon pouring into 30-50 ml. of cold water the colour becomes deep blue or green upon adding excess of sodium hydroxide solution. 

Method 2. Place a 3 0 g. sample of the mixture of amines in a flask, add 6g. (4-5 ml.) of benzenesulphonyl chloride (or 6 g. of p-toluenesulphonyl chloride) and 100 ml. of a 5 per cent, solution of sodium hydroxide. Stopper the flask and shake vigorously until the odour of the acid chloride has disappeared open the flask occasionally to release the pressure developed by the heat of the reaction. AUow the mixture to cool, and dissolve any insoluble material in 60-75 ml. of ether. If a solid insoluble in both the aqueous and ether layer appears at this point (it is probably the sparingly soluble salt of a primary amine, e.g., a long chain compound of the type CjH5(CH2) NHj), add 25 ml. of water and shake if it does not dissolve, filter it off. Separate the ether and aqueous layers. The ether layer will contain the unchanged tertiary amine and the sulphonamide of the secondary amine. Acidify the alkaline aqueous layer with dilute hydrochloric acid, filter off the sulphonamide of the primary amine, and recrystaUise it from dilute alcohol. Extract the ether layer with sufficient 5 per cent, hydrochloric acid to remove all the tertiary amine present. Evaporate the ether to obtain the sulphonamide of the secondary amine recrystaUise it from alcohol or dilute alcohol. FinaUy, render the hydrochloric acid extract alkaline by the addition of dilute sodium hydroxide solution, and isolate the tertiary amine. 

In a 250 ml. conical flask mix a solution of 14 g. of sodium hydroxide in 40 ml. of water and 21 g. (20 ml.) of pure benzaldehyde (Section IV,115). Add 15 g. of hydroxylamine hydrochloride in small portions, and shake the mixture continually (mechanical stirring may be employed with advantage). Some heat is developed and the benzaldehyde eventually disappears. Upon coohiig, a crystalline mass of the sodium derivative separates out. Add sufficient water to form a clear solution, and pass carbon dioxide into the solution until saturated. A colourless emulsion of the a or syn-aldoxime separates. Extract the oxime with ether, dry the extract over anhydrous magnesium or sodium sulphate, and remove the ether on a water bath. Distil the residue under diminished pressure (Fig. 11,20, 1). Collect the pure syn-benzaldoxime (a-benzald-oxime) at 122-124°/12 mm. this gradually solidifies on cooling in ice and melts at 35°. The yield is 12 g. 

This product is sufficiently pure for the preparation of phenylacetic acid and its ethyl ester, but it contains some benzyl tso-cyanide and usually develops an appreciable colour on standing. The following procedure removes the iso-cyanide and gives a stable water-white compound. Shake the once-distilled benzyl cyanide vigorously for 5 minutes with an equal volume of warm (60°) 60 per cent, sulphuric acid (prepared by adding 55 ml. of concentrated sulphuric acid to 100 ml. of water). Separate the benzyl cyanide, wash it with an equal volume of sa+urated sodium bicarbonate solution and then with an equal volume of half-saturated sodium chloride solution- Dry with anhydrous magnesium sulphate and distil under reduced pressure. The loss in washing is very small (compare n-Butyl Cyanide, Section 111,113, in which concentrated hydrochloric acid is employed). 

Xanthhydrol. Prepare an amalgam from 9 0 g. of clean sodium and 750 g. (55 ml.) of mercury (Section 11,50,7, Method 1), and warm it to 50° in a 500 ml. Pyrex bottle. Add a cold suspension of 25 g. of xanthone in 175 ml. of rectified spirit, stopper the bottle and shake vigorously raise the stopper from time to time to release the pressure. The temperature rises rapidly to 60-70°, the sohd xanthone passes into solution, and a transient blue colour is developed. After about 5 minutes the alcoholic solution is clear and almost colourless. Shake for a further 10 minutes, separate the mercury, and wash it with 15 ml. of alcohol. Filter the... 

Prepare the reagent by dissolving 7 -5 g. of sodium iodide in 50 ml. of A.R. acetone. The colourless solution gradually acquires a yellow colour. Keep it in a dark bottle. When a red-brown colour develops, it should be discarded. 

E. Vedejs (1978) developed a general method for the sterically controlled electrophilic or-hydroxylation of enolates. This uses a bulky molybdenum(VI) peroxide complex, MoO(02)2(HMPTA)(Py), which is rather stable and can be stored below 0 °C. If this peroxide is added to the enolate in THF solution (base e.g. LDA) at low temperatures, oneO—O bond is broken, and a molybdyl ester is formed. Excess peroxide is quenched with sodium sulfite after the reaction has occurred, and the molybdyl ester is cleaved to give the a-hydroxy car-... 

The main example of a category I indole synthesis is the Hemetsberger procedure for preparation of indole-2-carboxylate esters from ot-azidocinna-mates[l]. The procedure involves condensation of an aromatic aldehyde with an azidoacetate ester, followed by thermolysis of the resulting a-azidocinna-mate. The conditions used for the base-catalysed condensation are critical since the azidoacetate enolate can decompose by elimination of nitrogen. Conditions developed by Moody usually give good yields[2]. This involves slow addition of the aldehyde and 3-5 equiv. of the azide to a cold solution of sodium ethoxide. While the thermolysis might be viewed as a nitrene insertion reaction, it has been demonstrated that azirine intermediates can be isolated at intermediate temperatures[3]. 

During a relatively long period, the condensation of rhodanines with aldehydes was developed, especially by Andreasch s group (78-87). Finally, Holmberg (88, 89) described the best method to obtain rhodanines the condensation of ammonium dithiocarbamate with a sodium or potassium salt of an a-chloro acid. 

Hydrocortisone and Prednisolone. Following the discovery of the antiinflammatory actions of cortisone (1) and cortisol (2), there was a need not only to develop highly efficient routes to the corticoids, but to discover novel stmctures with fewer side effects than those of the corticoids, eg, sodium and water retention, reduced carbohydrate tolerance (steroid diabetes), osteoporosis, and depressed host defense. 

Phenol—formaldehyde (PF) was the first of the synthetic adhesives developed. By combining phenol with formaldehyde, which has exceptional cross-linking abiHties with many chemicals and materials, and a small amount of sodium hydroxide, a resin was obtained. The first resins soHdified as they cooled, and it was discovered that if it was ground to a powder with a small amount of additional formaldehyde and the appHcation of more heat, the mixture would Hquify and then convert to a permanently hard material. Upon combination of the powdered resin mixture with a filler material such as wood flour, the result then being placed in a mold and pressed under heat and pressure, a hard, durable, black plastic material was found to result. For many years these resulting products were called BakeHte, the trade name of the inventor. BakeHte products are still produced today, but this use accounts for only a small portion of the PF resins used. 

Copper acetate, ferrous acetate, silver acetate [563-63-3] basic aluminum acetate, nickel acetate [373-02-4] cobalt acetate, and other acetate salts have been reported to furnish anhydride when heated. In principle, these acetates could be obtained from low concentration acetic acid. CompHcations of soHds processing and the scarcity of knowledge about these thermolyses make industrial development of this process expensive. In the eady 1930s, Soviet investigators discovered the reaction of dinitrogen tetroxide [10544-72-6] and sodium acetate [127-09-3] to form anhydride ... 

Early demand for chlorine centered on textile bleaching, and chlorine generated through the electrolytic decomposition of salt (NaCl) sufficed. Sodium hydroxide was produced by the lime—soda reaction, using sodium carbonate readily available from the Solvay process. Increased demand for chlorine for PVC manufacture led to the production of chlorine and sodium hydroxide as coproducts. Solution mining of salt and the avadabiHty of asbestos resulted in the dominance of the diaphragm process in North America, whereas soHd salt and mercury avadabiHty led to the dominance of the mercury process in Europe. Japan imported its salt in soHd form and, until the development of the membrane process, also favored the mercury ceU for production. 

The ammonium chloride process, developed by Asahi Glass, is a variation of the basic Solvay process (9—11). It requires the use of soHd sodium chloride but obtains higher sodium conversions (+90%) than does the Solvay process. This is especially important ia Japan, where salt is imported as a soHd. The major difference from the Solvay process is that here the ammonium chloride produced is crystallized by cooling and through the addition of soHd sodium chloride. The resulting mother Hquor is then recycled to dissolve additional sodium chloride. The ammonium chloride is removed for use as rice paddy fertilizer. Ammonia makeup is generally suppHed by an associated synthesis plant. 

Sodium Hydroxide. Before World War 1, nearly all sodium hydroxide [1310-93-2], NaOH, was produced by the reaction of soda ash and lime. The subsequent rapid development of electrolytic production processes, resulting from growing demand for chlorine, effectively shut down the old lime—soda plants except in Eastern Europe, the USSR, India, and China. Recent changes in chlorine consumption have reduced demand, putting pressure on the price and availabiHty of caustic soda (NaOH). Because this trend is expected to continue, there is renewed interest in the lime—soda production process. EMC operates a 50,000 t/yr caustic soda plant that uses this technology at Green River it came onstream in mid-1990. Other U.S. soda ash producers have aimounced plans to constmct similar plants (1,5). 

The first reported synthesis of acrylonitrile [107-13-1] (qv) and polyacrylonitrile [25014-41-9] (PAN) was in 1894. The polymer received Htde attention for a number of years, until shortly before World War II, because there were no known solvents and the polymer decomposes before reaching its melting point. The first breakthrough in developing solvents for PAN occurred at I. G. Farbenindustrie where fibers made from the polymer were dissolved in aqueous solutions of quaternary ammonium compounds, such as ben2ylpyridinium chloride, or of metal salts, such as lithium bromide, sodium thiocyanate, and aluminum perchlorate. Early interest in acrylonitrile polymers (qv), however, was based primarily on its use in synthetic mbber (see Elastomers, synthetic). 

Dimethylformamide [68-12-2] (DME) and dimethyl sulfoxide [67-68-5] (DMSO) are the most commonly used commercial organic solvents, although polymerizations ia y-butyrolactoae, ethyleae carboaate, and dimethyl acetamide [127-19-5] (DMAC) are reported ia the hterature. Examples of suitable inorganic salts are aqueous solutioas of ziac chloride and aqueous sodium thiocyanate solutions. The homogeneous solution polymerization of acrylonitrile foUows the conventional kinetic scheme developed for vinyl monomers (12) (see Polymers). 

---