Process/catalyst development

Oxidative dehydrogenation processes Catalyst development Pt group Cu, Sn, and Cl 86... 

L Fan, K Yoshii, K Fujimoto. Selective synthesis of wax from syngas by supercritical phase process catalyst development. Sekiyu Gakkaishi 40 433-437, 1997. S-R Yan, L Fan, Z-X Zhang, J-L Zhou, K Fujimoto. a-Tetradecene cofeeding effect on the supercritical-phase Fischer-Tropsch synthesis over Co/Si02 catalysts. J Nat Gas Chem 7 127-133, 1998. 

The Reaction. Acrolein has been produced commercially since 1938. The first commercial processes were based on the vapor-phase condensation of acetaldehyde and formaldehyde (1). In the 1940s a series of catalyst developments based on cuprous oxide and cupric selenites led to a vapor-phase propylene oxidation route to acrolein (7,8). In 1959 Shell was the first to commercialize this propylene oxidation to acrolein process. These early propylene oxidation catalysts were capable of only low per pass propylene conversions (ca 15%) and therefore required significant recycle of unreacted propylene (9—11). 

Even ia 1960 a catalytic route was considered the answer to the pollution problem and the by-product sulfate, but nearly ten years elapsed before a process was developed that could be used commercially. Some of the eadier attempts iacluded hydrolysis of acrylonitrile on a sulfonic acid ion-exchange resia (69). Manganese dioxide showed some catalytic activity (70), and copper ions present ia two different valence states were described as catalyticaHy active (71), but copper metal by itself was not active. A variety of catalysts, such as Umshibara or I Jllmann copper and nickel, were used for the hydrolysis of aromatic nitriles, but aUphatic nitriles did not react usiag these catalysts (72). Beginning ia 1971 a series of patents were issued to The Dow Chemical Company (73) describiag the use of copper metal catalysis. Full-scale production was achieved the same year. A solution of acrylonitrile ia water was passed over a fixed bed of copper catalyst at 85°C, which produced a solution of acrylamide ia water with very high conversions and selectivities to acrylamide. 

Rhodium Ca.ta.lysts. Rhodium carbonyl catalysts for olefin hydroformylation are more active than cobalt carbonyls and can be appHed at lower temperatures and pressures (14). Rhodium hydrocarbonyl [75506-18-2] HRh(CO)4, results in lower -butyraldehyde [123-72-8] to isobutyraldehyde [78-84-2] ratios from propylene [115-07-17, C H, than does cobalt hydrocarbonyl, ie, 50/50 vs 80/20. Ligand-modified rhodium catalysts, HRh(CO)2L2 or HRh(CO)L2, afford /iso-ratios as high as 92/8 the ligand is generally a tertiary phosphine. The rhodium catalyst process was developed joindy by Union Carbide Chemicals, Johnson-Matthey, and Davy Powergas and has been Hcensed to several companies. It is particulady suited to propylene conversion to -butyraldehyde for 2-ethylhexanol production in that by-product isobutyraldehyde is minimized. 

The second reaction is called the Fischer-Tropsch synthesis of hydrocarbons. Depending on the conditions and catalysts, a wide range of hydrocarbons from very light materials up to heavy waxes can be produced. Catalysts for the Fischer-Tropsch reaction iaclude iron, cobalt, nickel, and mthenium. Reaction temperatures range from about 150 to 350°C reaction pressures range from 0.1 to tens of MPa (1 to several hundred atm) (77). The Fischer-Tropsch process was developed iadustriaHy under the designation of the Synthol process by the M. W. Kellogg Co. from 1940 to 1960 (83). 

One of the most efficient implementations of the slurry process was developed by Phillips Petroleum Company in 1961 (Eig. 5). Nearly one-third of all HDPE produced in the 1990s is by this process. The reactor consists of a folded loop with four long (- 50 m) vertical mns of a pipe (0.5—1.0 m dia) coimected by short horizontal lengths (around 5 m) (58—60). The entire length of the loop is jacketed for cooling. A slurry of HDPE and catalyst particles in a light solvent (isobutane or isopentane) circulates by a pump at a velocity of 5—12 m/s. This rapid circulation ensures a turbulent flow, removes the heat of polymeriza tion, and prevents polymer deposition on the reactor walls. 

Manufacture and Processing. Until World War II, phthaUc acid and, later, phthaUc anhydride, were manufactured primarily by Hquid-phase oxidation of suitable feedstocks. The favored method was BASF s oxidation of naphthalene [91-20-3] by sulfuric acid ia the presence of mercury salts to form the anhydride. This process was patented ia 1896. During World War I, a process to make phthaUc anhydride by the oxidation of naphthalene ia the vapor phase over a vanadium and molybdenum oxide catalyst was developed ia the United States (5). Essentially the same process was developed iadependendy ia Germany, with U.S. patents being granted ia 1930 and 1934 (6,7). 

HP Alkylation Process. The most widely used technology today is based on the HE catalyst system. AH industrial units built in the free world since 1970 employ this process (78). During the mid-1960s, commercial processes were developed to selectively dehydrogenate linear paraffins to linear internal olefins (79—81). Although these linear internal olefins are of lower purity than are a olefins, they are more cost-effective because they cost less to produce. Furthermore, with improvement over the years in dehydrogenation catalysts and processes, such as selective hydrogenation of diolefins to monoolefins (82,83), the quaUty of linear internal olefins has improved. 

Two catalysts have emerged as commercially viable. The Mobil—Badger ethylbenzene process, which has been in commercial use since 1980, employs a ZeoHte catalyst and operates in the gas phase. A Hquid-phase ethylbenzene process joindy Hcensed by Lummus and UOP uses a Y-type ZeoHte catalyst developed by Unocal. This Hquid-phase process was commercialized in 1990. The same Y-type ZeoHte catalyst used for the production of ethylbenzene is being offered for the production of cumene but has not yet been commercialized. 

Catalyst Development. Traditional slurry polypropylene homopolymer processes suffered from formation of excessive amounts of low grade amorphous polymer and catalyst residues. Introduction of catalysts with up to 30-fold higher activity together with better temperature control have almost eliminated these problems (7). Although low reactor volume and available heat-transfer surfaces ultimately limit further productivity increases, these limitations are less restrictive with the introduction of more finely suspended metallocene catalysts and the emergence of industrial gas-phase fluid-bed polymerization processes. 

It is carried out in the Hquid phase at 100—130°C and catalyzed by a soluble molybdenum naphthenate catalyst, also in a series of reactors with interreactor coolers. The dehydration of a-phenylethanol to styrene takes place over an acidic catalyst at about 225°C. A commercial plant (50,51) was commissioned in Spain in 1973 by Halcon International in a joint venture with Enpetrol based on these reactions, in a process that became known as the Oxirane process, owned by Oxirane Corporation, a joint venture of ARCO and Halcon International. Oxirane Corporation merged into ARCO in 1980 and this process is now generally known as the ARCO process. It is used by ARCO at its Channelview, Texas, plant and in Japan and Korea in joint ventures with local companies. A similar process was developed by Shell (52—55) and commercialized in 1979 at its Moerdijk plant in the Netherlands. The Shell process uses a heterogeneous catalyst of titanium oxide on siHca support in the epoxidation step. Another plant by Shell is under constmction in Singapore (ca 1996). 

In two processes under development as of 1997, the sulfur dioxide stream reacts with reduciag gas over a proprietary catalyst to form elemental sulfur. Both processes have achieved a sulfur recovery of 96% ia a single reactor. Multiple reactor systems are expected to achieve 99+% recovery of the feed sulfur. The direct sulfur recovery process (DSRP), under development at Research Triangle Institute, operates at high temperature and pressure. A similar process being developed at Lawrence Berkeley Laboratory is expected to operate near atmospheric pressure. 

Diacetone-L-sorbose (DAS) is oxidized at elevated temperatures in dilute sodium hydroxide in the presence of a catalyst (nickel chloride for bleach or palladium on carbon for air) or by electrolytic methods. After completion of the reaction, the mixture is worked up by acidification to 2,3 4,6-bis-0-isoptopyhdene-2-oxo-L-gulonic acid (2,3 4,6-diacetone-2-keto-L-gulonic acid) (DAG), which is isolated through filtration, washing, and drying. With sodium hypochlorite/nickel chloride, the reported DAG yields ate >90% (65). The oxidation with air has been reported, and a practical process was developed with palladium—carbon or platinum—carbon as catalyst (66,67). The electrolytic oxidation with nickel salts as the catalyst has also... 

Polymer Gasoline. Refinery trends tend to favor alkylation over polymerisation. Unlike the alkylation process, polymerisation does not require isobutane. The catalyst is usually phosphoric acid impregnated on kieselghur pellets. Polymerisation of butylenes is not an attractive alternative to alkylation unless isobutane is unavailable. The motor octane number of polymer gasoline is also low, and there is considerable shrinkage ia product volume. The only commercial unit to be built ia recent years is at Sasol ia South Africa. The commercial process was developed by UOP ia the 1940s (104). 

Oxychlorination of methane can yield significant amounts of methylene chloride. A number of patents were obtained by Lummus in the mid-1970s on a high temperature, molten salt oxychlorination process (22,23). Catalyst development work has continued and generally consists of mixtures of Cu, Ni, Cr, or Fe promoted with an alkah metal (24—27). There are no industrial examples of this process at the present time. 

In the 1930s, the Raschig Co. in Germany developed a different chlorobenzene-phenol process in which steam with a calcium phosphate catalyst was used to hydrolyze chlorobenzene to produce phenol (qv) and HCl (6). The recovered HCl reacts with air and benzene over a copper catalyst (Deacon Catalyst) to produce chlorobenzene and water (7,8). In the United States, a similar process was developed by the BakeHte Division of Union Carbide Corp., which operated for many years. The Durez Co. Hcensed the Raschig process and built a plant in the United States which was later taken over by the Hooker Chemical Corp. who made significant process improvements. 

Liquefaction. Liquefaction of coal to oil was first accompHshed in 1914. Hydrogen was placed with a paste of coal, heavy oil, and a small amount of iron oxide catalyst at 450° and 20 MPa (200 atm) in stirred autoclaves. This process was developed by the I. G. Earbenindustrie AG to give commercial quaUty gasoline as the principal product. Twelve hydrogenation plants were operated during World War II to make Hquid fuels (see CoAL... 

Advances in catalysis will result in the development of high yield, low waste manufacturing processes. Catalysts frequently allow the use of less reactive raw materials and intermediates, and less severe processing conditions. High yields and improved... 

Eor most gas process environments-refineries, catalyst development sites, research and development and plant laboratories-a knowledge of the exact composition of the... 

---