Zeohte catalysts

In 1993, UOP commercialized an improved Pt-based catalyst, 1-210. This catalyst is based on a molecular sieve, but not an alurninosihcate zeoHte. UOP claims that yields ate about 10% better than those for 1-9 catalyst. EB to xylenes conversion is about 22—25% with a Cg aromatics per pass loss of about 1.2—1.5%. As discussed below, UOP s Isomar process can also use zeoHte catalysts which convert EB to benzene rather than to xylenes. UOP has hcensed over 40 Isomar units. 

Mobil s High Temperature Isomerization (MHTI) process, which was introduced in 1981, uses Pt on an acidic ZSM-5 zeoHte catalyst to isomerize the xylenes and hydrodealkylate EB to benzene and ethane (126). This process is particularly suited for unextracted feeds containing Cg aHphatics, because this catalyst is capable of cracking them to light paraffins. Reaction occurs in the vapor phase to produce a PX concentration slightly higher than equiHbrium, ie, 102—104% of equiHbrium. EB conversion is about 40—65%, with xylene losses of about 2%. Reaction conditions ate temperature of 427—460°C, pressure of 1480—1825 kPa, WHSV of 10—12, and a H2/hydtocatbon molar ratio of 1.5—2 1. Compared to the MVPI process, the MHTI process has lower xylene losses and lower formation of heavy aromatics. 

Mobil MTG and MTO Process. Methanol from any source can be converted to gasoline range hydrocarbons using the Mobil MTG process. This process takes advantage of the shape selective activity of ZSM-5 zeoHte catalyst to limit the size of hydrocarbons in the product. The pore size and cavity dimensions favor the production of C-5—C-10 hydrocarbons. The first step in the conversion is the acid-catalyzed dehydration of methanol to form dimethyl ether. The ether subsequendy is converted to light olefins, then heavier olefins, paraffins, and aromatics. In practice the ether formation and hydrocarbon formation reactions may be performed in separate stages to faciHtate heat removal. 

The production of ketene by this method has no significant environmental impact. The off-gases from the ketene furnace are either circulated to the furnace and burned to save energy or led to a flare system. The reaction can also be carried out at 350—550°C in the presence of alkaH-exchanged zeoHte catalysts (54). Small quantities of ketene are prepared by pyrolysis of acetone [67-64-1] at 500—700°C in a commercially available ketene lamp (55,56). 

The methyl a-hydroxyisobutyrate produced is dehydrated to MMA and water in two stages. First, the methyl a-hydroxyisobutyrate is vaporized and passed over a modified zeoHte catalyst at ca 240°C. A second reactor containing phosphoric acid is operated at ca 150°C to promote esterification of any methacrylic acid (MAA) formed in the first reactor (74,75). Methanol is co-fed to improve selectivity in each stage. Conversions of methyl a-hydroxyisobutyrate are greater than 99%, with selectivities to MMA near 96%. The reactor effluent is extracted with water to remove methanol and yield cmde MMA. This process has not yet been used on a commercial scale. 

Dispersed Metals. Bifimctional zeoHte catalysts, principally zeoHte Y, are used in commercial processes such as hydrocracking. These are acidic zeoHtes containing dispersed metals such as platinum or palladium. The metals are introduced by cation exchange of the ammine complexes, foUowed by a reductive decomposition (21) ... 

Vapor-Phase Processes. Although vapor-phase alkylation has been practiced since the early 1940s, it could not compete with Hquid-phase processes until the 1970s when the Mobil—Badger vapor-phase ethylbenzene process was introduced (Eig. 4). The process is based on Mobil s ZSM-5 zeohte catalyst (38,52,53). The nonpoUuting and noncorrosive nature of the process is one of its major advantages over the AlCl hquid-phase system. 

The Xylene Plus process of ARGO Technology, Inc. (95,96) and the FINA T2BX process (97) also use a fixed-bed catalyst in the vapor phase for transalkylation of toluene to produce xylenes and benzene. The Mobil low temperature disproportionation (LTD) process employs a zeoHte catalyst for transalkylation of toluene in the Hquid phase at 260—315°C in the absence of hydrogen (98). 

The selective alkylation of toluene with methanol to produce -xylene as a predominant isomer can be achieved over shape-selective catalysts (99—101). With a modified ZSM-5 zeoHte catalyst, more than 99% -xylene in xylene isomers can be produced at 550°C. This -xylene concentration exceeds the equiHbrium concentration of 23% (99). The selective synthesis of -xylene using relatively low cost toluene is economically attractive however, this technology was not commercialized as of 1991. 

DMN can be produced by alkylating naphthalene or 2-methylnaphthalene at 250—450°C over ZeoHte catalysts (102,103). However, no commercial technology by this synthetic route had been developed as of 1991, primarily because of low catalytic selectivity. 

Two catalysts have emerged as commercially viable. The Mobil—Badger ethylbenzene process, which has been in commercial use since 1980, employs a ZeoHte catalyst and operates in the gas phase. A Hquid-phase ethylbenzene process joindy Hcensed by Lummus and UOP uses a Y-type ZeoHte catalyst developed by Unocal. This Hquid-phase process was commercialized in 1990. The same Y-type ZeoHte catalyst used for the production of ethylbenzene is being offered for the production of cumene but has not yet been commercialized. 

Methylphenol. This phenol, commonly known as o-cresol, is produced synthetically by the gas phase alkylation of phenol with methanol using modified alumina catalysis or it may be recovered from naturally occurring petroleum streams and coal tars. Most is produced synthetically. Reaction of phenol with methanol using modified zeoHte catalysts is a concerted dehydration of the methanol and alkylation of the aromatic ring. 2-Methylphenol [95-48-7] is available in 55-gal dmms (208-L) and in bulk quantities in tank wagons and railcars. 

In recent years alkylations have been accompHshed with acidic zeoHte catalysts, most nobably ZSM-5. A ZSM-5 ethylbenzene process was commercialized joiatiy by Mobil Co. and Badger America ia 1976 (24). The vapor-phase reaction occurs at temperatures above 370°C over a fixed bed of catalyst at 1.4—2.8 MPa (200—400 psi) with high ethylene space velocities. A typical molar ethylene to benzene ratio is about 1—1.2. The conversion to ethylbenzene is quantitative. The principal advantages of zeoHte-based routes are easy recovery of products, elimination of corrosive or environmentally unacceptable by-products, high product yields and selectivities, and high process heat recovery (25,26). 

ABB Lummus Crest Inc. and Unocal Corp. have Hcensed a benzene alkylation process usiag a proprietary zeoHte catalyst. Unlike the Mobil-Badger process, the Unocal-Lummus process is suitable for either ethylbenzene or cumene manufacture (27,28). 

A completely new approach for BTX production has emerged in recent years. It converts to paraffins into aromatics using a modified ZSM-5 zeoHte catalyst which contains gallium (19). An example of this approach, the Cyclar process, has been in commercial operation by British Petroleum at Grangemouth, Scotiand since August 1990 (20). It uses C —feed and employs UOP s CCR technology to compensate for rapid catalyst coking. 

Alkylation. Ethylbenzene [100-41 -4] the precursor of styrene, is produced from benzene and ethylene. The ethylation of benzene is conducted either ia the Hquid phase ia the preseace of a Eriedel-Crafts catalyst (AlCl, BE, EeCl ) or ia the vapor phase with a suitable catalyst. The Moasanto/Lummus process uses an aluminum chloride catalyst that yields more than 99% ethylbenzene (13). More recently, Lummus and Union Oil commercialized a zeoHte catalyst process for Hquid-phase alkylation (14). Badger and Mobil also have a vapor-phase alkylation process usiag zeoHte catalysts (15). Almost all ethylbenzene produced is used for the manufacture of styrene [100-42-5] which is obtained by dehydrogenation ia the preseace of a suitable catalyst at 550—640°C and relatively low pressure, <0.1 MPa (<1 atm). 

ZeoHte catalysts and adsorbents are widely accepted in industry. Commercial adsorbents based on synthetic aluminosihcates zeolite A and X became available in 1948 [4]. Zeolite Y as FCC catalyst became commercially available in 1964 [5]. 

As described in the previous section, the silica-alumina catalyst covered with the silicalite membrane showed exceUent p-xylene selectivity in disproportionation of toluene [37] at the expense of activity, because the thickness of the sihcahte-1 membrane was large (40 pm), limiting the diffusion of the products. In addition, the catalytic activity of silica-alumina was not so high. To solve these problems, Miyamoto et al. [41 -43] have developed a novel composite zeohte catalyst consisting of a zeolite crystal with an inactive thin layer. In Miyamoto s study [41], a sihcahte-1 layer was grown on proton-exchanged ZSM-5 crystals (silicalite/H-ZSM-5) [42]. The silicalite/H-ZSM-5 catalysts showed excellent para-selectivity of >99.9%, compared to the 63.1% for the uncoated sample, and independent of the toluene conversion. 

The reason for the high selectivity of zeohte catalysts is the fact that the catalytic reaction typically takes place inside the pore systems of the zeohtes. The selectivity in zeohte catalysis is therefore closely associated to the unique pore properties of zeohtes. Their micropores have a defined pore diameter, which is different from all other porous materials showing generally a more or less broad pore size distribution. Therefore, minute differences in the sizes of molecules are sufficient to exclude one molecule and allow access of another one that is just a little smaller to the pore system. The high selectivity of zeolite catalysts can be explained by three major effects [14] reactant selectivity, product selectivity, and selectivity owing to restricted size of a transition state (see Figure 4.11). 

Many procedures that are used in zeolite catalyst and adsorbent manufacture are common to other manufactured products. The unit operahons and equipment that are used can therefore be found throughout the catalyst and adsorbent manufacturing industries. There are a number of books and monographs that outhne equipment and manufacturing procedures that are relevant to zeoHte catalysts and adsorbents [65-68]. 

ISAL A hydrotreating process for removing sulfur and nitrogen compounds from petroleum fractions without reducing their octane values. Developed by Intevep SA, the research and technology arm of Venezuela s state petroleum company PDVSA. A proprietary zeohte catalyst first saturates the olefins and then isomerizes them to higher octane-value compounds. 

Q-Max A process for making cumene from benzene and propylene by catalytic alkylation using a proprietary regenerable zeohte catalyst. Developed by UOP and first installed in 1996 by JLM Chemicals in Illinois. 

In principle, the same rules hold true when zeolitic alkylation catalysts are used. A detailed study of the influence of PO and OSV on the performance of zeohte H-BEA in a backmix reactor was reported by de Jong et al. 80). The authors developed a simple model of the kinetics, which predicted catalyst lifetimes as a function of P/O and OSV. Catalyst lifetime (which is equivalent to the catalyst productivity, the reciprocal of acid consumption) increased with increasing P/O ratio and decreasing OSV. Furthermore, the authors persuasively demonstrated the superiority of a backmix reactor over a plug flow reactor. Qualitatively similar results were obtained by Taylor and Sherwood (222) employing a USY zeohte catalyst in a backmix reactor. The authors stressed the detrimental effect of unreacted alkene on the catalyst lifetime and product quality. Feller et al. (89) tested LaX zeohtes in a backmix reactor and found the catalyst productivity to be nearly independent of the OSV within the examined OSV range. At higher values of OSV, the catalyst life was shorter, but in this shorter time the same total amount of product was produced. The P/O ratio had only a moderate influence on the catalyst performance. 

Catalysis. Various forms of zeohte Y find uses in industrial catalytic processes. These have already been listed in Table 31 and account for the second highest annual tomiage use of synthetic zeolites (approx 60 000 metric toimes). This continues to increase as zeohte catalysts aid the shift to unleaded gasoline and to the use of cheaper feedstocks. 

---