Polyvinyl adsorption

Direct measurements on metals such as iron, nickel and stainless steel have shown that adsorption occurs from acid solutions of inhibitors such as iodide ions, carbon monoxide and organic compounds such as amines , thioureas , sulphoxides , sulphidesand mer-captans. These studies have shown that the efficiency of inhibition (expressed as the relative reduction in corrosion rate) can be qualitatively related to the amount of adsorbed inhibitor on the metal surface. However, no detailed quantitative correlation has yet been achieved between these parameters. There is some evidence that adsorption of inhibitor species at low surface coverage d (for complete surface coverage 0=1) may be more effective in producing inhibition than adsorption at high surface coverage. In particular, the adsorption of polyvinyl pyridine on iron in hydrochloric acid at 0 < 0 -1 monolayer has been found to produce an 80% reduction in corrosion rate . 

Hydrophilic interaction chromatography on Asahipak NH2P or Excel-pak CHA-P44 with pulsed amperometric detection has been used to fractionate malto-oligosaccharides.266 The Asahipak NH2P is a polyvinyl alcohol support with a polyamine bonded phase, and the Excelpak is a sulfonated polystyrene in the Zn+2 form. Amine adsorption of sialic acid-containing oligosaccharides was performed on a Micropak AX-5 column (Varian) using acetonitrile-water-acetic acid-triethylamine.267... 

A colloidal suspension of conductive vanadium pentoxide [130] can be used to perform intercalation, adsorption or encapsulation of electroactive molecules or biomolecules for electrodes or biosensor realization [131]. Encapsulation of glucose oxidase in nanocomposite films made with polyvinyl alcohol and V205 sol-gel matrix or in ferrocene intercalated V2Os sol-gel [132] were envisaged to prepare glucose biosensors. 

Adsorption-Desorption Behavior of Polyvinyl Alcohol on Polystyrene Latex Particles... 

The adsorption of fully and partially hydrolyzed (88%) polyvinyl alcohol (PVA) on 190-1lOOnm monodisperse polystyrene latex particles was investigated. The effect of molecular weight was investigated for 190 nm-size particles using the serum replacement adsorption and desorption methods. The adsorption density at the adsorption-isotherm plateau followed the relationships for the fully hydrolyzed... 

Polymer adsorption is important in the flocculation and stabilization of colloidal sols and has been reviewed by Vincent et al. (1) and Tadros (2). Polyvinyl alcohol (PVA) has been used in these studies because of its practical application in textiles, adhesives, and coatings. The adsorption of PVA has been studied on silver iodide by Fleer (3) and Koopal (4), and on polystyrene (PS) latex particles by Garvey (5). The adsorption isotherms reported by these workers extend up to 600 ppm PVA. The adsorption at... 

The determination of adsorption isotherms at liquid-solid interfaces involves a mass balance on the amount of polymer added to the dispersion, which requires the separation of the liquid phase from the particle phase. Centrifugation is often used for this separation, under the assumption that the adsorption-desorption equilibrium does not change during this process. Serum replacement (6) allows the separation of the liquid phase without assumptions as to the configuration of the adsorbed polymer molecules. This method has been used to determine the adsorption isotherms of anionic and nonionic emulsifiers on various types of latex particles (7,8). This paper describes the adsorption of fully and partially hydrolyzed PVA on different-size PS latex particles. PS latex was chosen over polyvinyl acetate (PVAc) latex because of its well-characterized surface PVAc latexes will be studied later. 

Traditionally, ultrafilters have been manufactured from cellulose acetate or cellulose nitrate. Several other materials, such as polyvinyl chloride and polycarbonate, are now also used in membrane manufacture. Such plastic-type membranes exhibit enhanced chemical and physical stability when compared with cellulose-based ultrafiltration membranes. An important prerequisite in manufacturing ultrafilters is that the material utilized exhibits low protein adsorptive properties. 

Fig. 4.16 provides an illustration of the adsorption of a neutral polymer, polyvinyl alcohol, on a polar surface, and the resulting effects on the double layer properties. Adsorption of anionic polymers on negative surfaces - especially in the presence of Ca2+ or Mg2+ which may act as coordinating links between the surface and functional groups of the polymer - is not uncommon (Tipping and Cooke, 1982). 

Amiodarone adsorbs to polyvinyl chloride (PVC) tubing, and the clinical trial dose administration schedule was designed to account for this adsorption. Clinical trials were conducted using PVC tubing therefore its use is recommended. The concentrations and rates of infusion provided in Administration and Dosage reflect doses identified in these studies. It is important that the recommended infusion regimen be followed closely. 

Chiellini E, Corti A, Politi B, Solaro R (2000) Adsorption/desorption of polyvinyl alcohol on solid substrates and relevant biodegradation. J Polym Environ 8 67-79... 

Solute adsorption can be minimized most effectively by capillary wall coating, thereby decreasing the free energy of hydrophobic or ionic interactions. Coating can be achieved either by covalently bonded organic modifiers, e.g., polyacrylamides, sulfonic acids, polyethylene glycols, maltose, and polyvinyl pyrolidinone, or by dynamic deactivation (i.e., addition of... 

Wang, P. L., Udeani, G O. and Johnston, T. P. (1995), Inhibition of granulocyte colony stimulating factor (c-csf) adsorption to polyvinyl chloride using a nonionic surfactant, Int. I. Pharm., 114,177-184. 

It appears from these data that adsorption to hydrophilic surfaces would be a viable strategy. Other research produced a similar conclusion. Waugh et al. showed that prothrombin (another member of the coagulation cascade) binds more strongly to polymethyl methacrylate than glass, ("hating showed that plasma proteins bind more strongly to polyvinyl chloride than a hydrophilic dialysis membrane. 

While initial aging did cause some loss in volume resistivity, it was no more severe in unstabilized than in stabilized compositions. The most startling effect was the marked increase in volume resistivity under severe aging conditions. This may be due to volatilization loss of DOP or cross-linking of polyvinyl chloride, both of which could reduce migration of ionic impurities, or it may involve adsorption of ionic impurities by the dark-colored, conjugated, polyene structure which forms by loss of hydrogen chloride. In any case it deserves further study. 

Recent investigations have shown that the behavior and interactions of surfactants in a polyvinyl acetate latex are quite different and complex compared to that in a polystyrene latex (1, 2). Surfactant adsorption at the fairly polar vinyl acetate latex surface is generally weak (3,4) and at times shows a complex adsorption isotherm (2). Earlier work (5,6) has also shown that anionic surfactants adsorb on polyvinyl acetate, then slowly penetrate into the particle leading to the formation of a poly-electroyte type solubilized polymer-surfactant complex. Such a solubilization process is generally accompanied by an increase in viscosity. The first objective of this work is to better under-stand the effects of type and structure of surfactants on the solubilization phenomena in vinyl acetate and vinyl acetate-butyl acrylate copolymer latexes. 

It is well known (3,5,6) that sodium lauryl sulfate interacts with some polymers such as polyvinyl acetate causing solubilization of the insoluble polymer leading to an increase in viscosity. In Figure 3, viscosity of the homopolymer and 70/30 VA/BA at various NaLS/polymer ratio is shown. It is seen that the viscosity of the 2% latex dispersion increases with increase in NaLS/polymer ratio. Similar visoosity data for the 85/15 VA/BA was intermediate between the homopolymer and 70/30 VA/BA latexes. Surfactants that showed a normal saturation type adsorption behavior did not show any significant visoosity increase of the latex. 

The most popular thin layer is silica gel, and it is estimated that about 90% of TLC separations are performed on standard TLC silica plates a common size is 20 cm square and 250 g,m thick. Binders, in amounts up to 15%, are usually used to produce a stable layer and good adherence to the backing plate, but plates can be made without binders. Calcium sulfate (gypsum, designated with a G in the name, e.g., silica gel G) and polyvinyl alcohol (PVA) are most common. The PVA plates are very stable and will withstand rather rough handling. While it is not difficult to make one s own plates, most laboratories prefer commercially prepared plates, especially those made with PVA. It must not be forgotten, however, that both binders will modify the adsorption properties of the silica and can produce somewhat different separations. 

Dyeing of Heparin on PVPyr. The transparent films of polyvinyl-pyridine permit demonstration of the presence of heparin, and some judgment of the uniformity of adsorption, by staining with a basic dye such as toluidine blue or azure A, which combine with heparin to form... 

Journal of Materials Science. Materials in Medicine 14, No.10, Oct.2003, p.905-12 BLOOD RESPONSE TO PLASTICIZED POLYVINYL CHLORIDE. DEPENDENCE OF FIBRINOGEN ADSORPTION ON PLASTICIZER SELECTION AND SURFACE PLASTICIZER LEVEL... 

PLASTICISED POLYVINYL CHLORIDE. DEPENDENCE OF FIBRINOGEN ADSORPTION ON PLASTICISER SELECTION AND SURFACE PLASTICISER LEVEL... 

Quite similar results have been reported by van Vliet [226]. He found that the equilibrium thickness of foam films from aqueous solutions of polyvinyl alcohol at low pressure is much larger than twice the adsorption layer thickness measured by ellipsometry. The core thickness is again several times the radius of gyration of the polymer molecules in... 

The stabilising action of the adsorption layers from high molecular substances (protective colloids) is related to the decrease in the forces of molecular attraction. Hence, films from aqueous solution of polyvinyl alcohol obtained between drops of cyclohexane have thickness of 80 nm and respectively, a very low attraction force, in contrast to black films [513]. Along with that the adsorption layers from such compounds possess visco-elasticity properties with modulus of elasticity 104 N m"2, impeding the film thinning and drop coalescence [503]. 

---