Plastics additives plasticizers

Focus on Plastics Additives Plastics News Japan... 

The aromatic extracts have been used in the paint industry to partially replace linseed oil. They are still used for producing printer s ink. In addition, they are finding a variety of applications as plasticizers in the rubber industry or for the manufacture of plastics such as PVC. 

In addition, on the basis of analogous specimens, the accumulation of damage and plastic deformation of metal structure were simulated. These results provide the possibility to obtain the prediction charts of the metal work s residual resource. 

The properties of the piezocomposite material mentioned above offer special benefits when the transducer is coupled to a material of low acoustic impedance. This especially applies to probes having plastic delay lines or wedges and to immersion and medical probes. These probes with piezocomposite elements can be designed to have not only a high sensitivity but also at the same time an excellent resolution and, in addition, the effort required for the probe s mechanical damping can be reduced. 

Atomistically detailed models account for all atoms. The force field contains additive contributions specified in tenns of bond lengtlis, bond angles, torsional angles and possible crosstenns. It also includes non-bonded contributions as tire sum of van der Waals interactions, often described by Lennard-Jones potentials, and Coulomb interactions. Atomistic simulations are successfully used to predict tire transport properties of small molecules in glassy polymers, to calculate elastic moduli and to study plastic defonnation and local motion in quasi-static simulations [fy7, ( ]. The atomistic models are also useful to interiDret scattering data [fyl] and NMR measurements [70] in tenns of local order. 

Commercially produced elastic materials have a number of additives. Fillers, such as carbon black, increase tensile strength and elasticity by forming weak cross links between chains. This also makes a material stilfer and increases toughness. Plasticizers may be added to soften the material. Determining the effect of additives is generally done experimentally, although mesoscale methods have the potential to simulate this. 

After the addition of the propyne the thermometer-gas outlet combination was replaced with a "cold finger" filled with dry-ice and acetone. The top of this reflux condenser was connected via a plastic tube with a cold trap (-75°C) containing 50 ml of dry THF. The cooling bath was removed and the conversion of propyne started... 

A suspension of 0.40 mol of sodium amide in 300 ml of liquid ammonia was prepared as described in Chapter II, Exp. 11. To the suspension was added with swirling a mixture of 0.25 mol of CHgCeC-S-Ph (see Chapter IV, Exp. 14) and 40 ml of THE in about 2 min (note 1). Swirling was continued after the addition. Three minutes later (note 1) the stopper with glass tube was placed on the flask. The brown solution was forced through the glass tube and the plastic tube, connected to it under 400 g of finely crushed ice, which was contained in a 3-1 conical flask (see Chapter I, Fig. 3, and accompanying description of this operation). The flask was placed for... 

Results obtained for two mixed plastics are summarized in Table 4. A balance exists between process temperature, plastics feed rate, and product yields (67). For example, lower temperatures increase wax formation due to incomplete depolymerization. Slower feed rates and increased residence times reduce wax formation and increase the yield of Hquids. The data summarized in Table 4 illustrate that the addition of PET to a HDPE PP PS mixture changes the performance of the Conrad process. Compared to the reference HDPE PP PS mixture, increased amounts of soHds ate formed. These are 95% terephthahc acid and 5% mono- and bis-hydroxyethyl esters. At higher temperatures, apparentiy enough water remains to promote decarboxylation. 

Commercially, urea is produced by the direct dehydration of ammonium carbamate, NH2COONH4, at elevated temperature and pressure. Ammonium carbamate is obtained by direct reaction of ammonia and carbon dioxide. The two reactions are usually carried out simultaneously in a high pressure reactor. Recendy, urea has been used commercially as a catde-feed supplement (see Feeds and feed additives). Other important appHcations are the manufacture of resins (see Amino resins and plastics), glues, solvents, and some medicinals. Urea is classified as a nontoxic compound. 

Urea is also used as feed supplement for mminants, where it assists in the utilization of protein. Urea is one of the raw materials for urea—formaldehyde resins. Urea (with ammonia) pyrolyzes at high temperature and pressure to form melamine plastics (see also Cyanamides). Urea is used in the preparation of lysine, an amino acid widely used in poultry feed (see Amino acids Feeds and feed additives, petfoods). It also is used in some pesticides. 

Phenol—formaldehyde (PF) was the first of the synthetic adhesives developed. By combining phenol with formaldehyde, which has exceptional cross-linking abiHties with many chemicals and materials, and a small amount of sodium hydroxide, a resin was obtained. The first resins soHdified as they cooled, and it was discovered that if it was ground to a powder with a small amount of additional formaldehyde and the appHcation of more heat, the mixture would Hquify and then convert to a permanently hard material. Upon combination of the powdered resin mixture with a filler material such as wood flour, the result then being placed in a mold and pressed under heat and pressure, a hard, durable, black plastic material was found to result. For many years these resulting products were called BakeHte, the trade name of the inventor. BakeHte products are still produced today, but this use accounts for only a small portion of the PF resins used. 

The important solvent and plasticizer intermediate, 2-ethylhexanol, is manufactured from -butyraldehyde by aldol addition in an alkaline medium at 80-130°C and 300-1010 kPa (3-10 atm). 

---