Solid content

The solids content of an adhesive or sealant should be checked to ensure that formulation or dilution errors have not been made. Solids can refer to the nonvolatile component of the adhesive or the inorganic component of the adhesive. 

ASTM D 1489 offers a test method for determining the nonvolatile content of aqueous adhesives. The solids content (or conversely the volatile content) is a measurement of the actual nonvolatile materials that are contained within the formulation. Addition of solvent can be used to correct the viscosity of adhesives or sealants to account for variability in the manufacturing process or inconsistent base materials in the resin formulation. 

---

In practice, tliere are various ways by which ( ) can be detennined for a given sample, and tire results may be (slightly) different. In particular, for sterically stabilized particles, tire effective hard-sphere volume fraction will be different from tire value obtained from tire total solid content. 

Slurry or slip casting provides a relatively inexpensive way to fabricate unifonn-thickness, thin-wall, or large cross section shapes [4o, 44, 45, 46, 42 aiid 48]. For slip casting, a slurry is first poured into a porous mould. Capillary suction then draws the liquid from the slurry to fonn a higher solids content, close-packed, leather-hard cast on the inner surface of the mould. In a fixed time, a given wall thickness is fonned, after which the excess slurry is drained. 

Solution Polymers. Acryflc solution polymers are usually characterized by their composition, solids content, viscosity, molecular weight, glass-transition temperature, and solvent. The compositions of acryflc polymers are most readily determined by physicochemical methods such as spectroscopy, pyrolytic gas—liquid chromatography, and refractive index measurements (97,158). The solids content of acryflc polymers is determined by dilution followed by solvent evaporation to constant weight. Viscosities are most conveniently determined with a Brookfield viscometer, molecular weight by intrinsic viscosity (158), and glass-transition temperature by calorimetry. 

Evaporated milk is a Hquid product obtained by the partial removal of water only from milk. It has a minimum milk-fat content of 7.5 mol % and a minimum milk-solids content of 25.0 mol %. Evaporated skimmed milk is a Hquid product obtained by the partial removal of water only from skimmed milk. It has a minimum milk-solids content of 20.0 mol %. Sweetened condensed milk is a product obtained by the partial removal of water only from milk with the addition of sugars. It has a minimum milk-fat content of 8.0 mol % and a minimum milk-solids content of 28.0 mol %. Skimmed sweetened condensed milk is a product obtained by the partial removal of water only from skimmed milk with the addition of sugars. It has a minimum milk-solids content of 24.0 mol %. AH may contain food additives (qv) as stabilizers, in maximum amounts, including sodium, potassium, and calcium salts of hydrochloric acid at 2000 mg/kg singly citric acid, carbonic acid, orthophosphoric acid, and polyphosphoric acid at 3000 mg/kg in combination, expressed as anhydrous substances and in the evaporated milk carrageenin may be added at 150 mg/kg. 

Purity = sugar content as percent of total dissolved solids content. 

The second type of thin-film evaporator, termed a wiped-film evaporator, introduces feed material on a heated waU of a cylinder. Rotating wiper blades continuously spread the feed along the inner waU of the cylinder to maintain uniformity of thickness and to ensure contact with the heated surface. The volatile components are driven off and coUected on an internal chilled condenser surface. The condensate or distUlate is removed continuously. At the end of the process, the residual becomes dry and heavy and drops to the bottom of the unit for removal. The wiped-film evaporator is best suited for treatment of viscous or high-solids content feed. 

Typically, grape skin extract has a specific gravity of 1.13 g/mL at 20°C, a solids content of 28—32° Brix (=t3°), a pH of 3.0, and a color strength as anthocyanin of about 1.25% (as measured at 520 nm ia pH 3.0 citrate buffet). Grape skin extract is also available as spray-dried powders with color values three to four times those of the liquid. The properties and uses of grape skin extract ate similar to those of grape color extract. 

The usual measuring device for feed flow is a magnetic flowmeter, which is a volumetric device whose output F must be multiplied by density p to produce mass flowMo- For most aqueous solutions which are fed to evaporators, the product of density and the function of solid content appearing above is linear with density ... 

The physical properties of spray-dried materials are subject to considerable variation, depending on the direction of flow of the inlet gas and its temperature, the degree and uniformity of atomization, the solids content of the feed, the temperature of the feed, and the degree of aeration of the feed. The properties of the product usually of greatest interest are (1) particle size, (2) bulk density, and (3) dustiness. The particle size is a function of atomizer-operating conditions and also of the solids content, liquid viscosity, liquid density, and feed rate. In general, particle size increases with solids content, viscosity, density, and feed rate. 

Many larger installations also feature a batch stiU. Material to be separated may be high in solids content, or it might contain tars or resins that would plug or foul a continuous unit. Use of a batch unit can keep solids separated and permit convenient removal at the termination of the process. 

In some crystalhzation apphcations it is desirable to increase the solids content of the shiny within the body above the natural consis-tencw, which is that developed by equilibrium cooling of the incoming feed solution to the final temperature. This can be done by withdrawing a stream of mother liquor from the baffle zone, thereby thickening the shiny within the growing zone of the crystallizer. This mother liquor is also available for removal of fine ciystals for size control of the product. 

Density Gauges These are used to measure the density or suspended solids content of the feed and underflow streams. Gamma radiation devices are the most commonly used for automatic control, but ultrasonic devices are effective in the lower range of slurry density. Marcy pulp density scales are an effective manually operated device. A solids mass flow indication is usually obtained by combining a density gauge output with the output from a flowmeter. 

The value of tire heat transfer coefficient of die gas is dependent on die rate of flow of the gas, and on whether the gas is in streamline or turbulent flow. This factor depends on the flow rate of tire gas and on physical properties of the gas, namely the density and viscosity. In the application of models of chemical reactors in which gas-solid reactions are caiTied out, it is useful to define a dimensionless number criterion which can be used to determine the state of flow of the gas no matter what the physical dimensions of the reactor and its solid content. Such a criterion which is used is the Reynolds number of the gas. For example, the characteristic length in tire definition of this number when a gas is flowing along a mbe is the diameter of the tube. The value of the Reynolds number when the gas is in streamline, or linear flow, is less than about 2000, and above this number the gas is in mrbulent flow. For the flow... 

In addition, with high solid content of the cooling water and at high flow velocities, severe corrosive conditions exist which continuously destroy surface films. Cathodic protection alone is not sufficient. Additional measures must be undertaken to promote the formation of a surface film. This is possible with iron anodes because the anodically produced hydrated iron oxide promotes surface film formation on copper. 

Suifate (S04>-2 Adds to solids content of water, but, in itself, is not usually significant combines with calcium to form calcium sulfate scale Demineralization, distillation, reverse osmosis, electrodialysis... 

Conductivity Expressed as micromhos, specific conductance Conductivity is the result of ionizable solids in solution high conductivity can increase the corrosive characteristics of a water Any process which decreases dissolved solids content will decrease conductivity examples are demineralization, lime softening... 

Total solids contents 36% (including dry rubber eonlent... 

---