Floor adhesives

About 100 billion pounds of chemicals and polymers are made from ethylene each year. In fact, over 40% of all organic chemicals produced are based on ethylene. These ethylene-based materials are found in almost every conceivable application encountered in daily life, for example, containers, flooring, adhesives, pharmaceuticals, oil and gasoline additives, paints, surfactants, etc. [Pg.120]

Floor adhesive (water based) Nonane, decane, undecane, dimethyloctane, 2-methylnonane, dimethylbenzene... [Pg.853]

GEV EMICODE (2001) Labelling Scheme for Flooring Installation Products including flooring adhesives, primers and levelling compounds http //www.emicode.com/ gev-uk/gev.htm... [Pg.145]

Construction sealants Protective coatings Industrial flooring Adhesives for bonding wood Waterproofing systems... [Pg.17]

The possible sources for the most important chemical compounds identified in the European Audit project are presented in Table 5 [50]. The most important source of VOCs was materials, especially furnishings. The dominant VOCs detected in the majority of the buildings were solvents used in floor or wall coverings and pressed-wood products (carpets, PVC flooring, floor adhesives, wallpaper, particle board, etc.). [Pg.203]

In many applications of low molecular weight hydrocarbon resins, including flooring, adhesives, rubber compounds, inks, and coatings, the best performance is often associated with plasticizers that are marginal solvents rather than perfect ones. The difference between the resin parameter and the plasticizer parameter indicates the place of the system in the Flory-Huggins phase diagram. The separation of phases is responsible for the improved physical properties. While the difference of the parameters readily explains the behavior, the parameters for many industrial materials are not sufficiently well defined, and specific solubility tests must be used to control both resin and plasticizer. [Pg.139]

Tlhis study was made to reconcile the behavior of low molecular weight hydrocarbon resins and the behavior of their plasticizers with the solubility parameter and with the Flory-Huggins treatment of phase separation from polymer solutions. These resins are widely used industrially for coatings, floorings, adhesives, rubber compounds, and many other applications. Since they are usually hard and brittle, they are used with rubber, drying oils, plastics, or with plasticizers. [Pg.139]

The results of the calculations performed on the data for the contact cement and floor adhesive are displayed below in Tables 3 and 4. [Pg.22]

Tall resins colopho-nium derivatives Hotmelts, flooring adhesives Extender, tackifier... [Pg.433]

Uses Epoxy for high solids/100% solids coatings, flooring, adhesives, and civil engineering applies. [Pg.246]

Uses Curing agent for coatings, flooring, adhesives, grouts Properties Gardner 10 max. color dens. 8.1 Ib/gal vise. 900-2000 cP amine no. 580-620 EEW 66 gel time 45 min (100 g mass with Epon Resin 828)... [Pg.323]

Uses Epoxy curing agent for high-solids coatings, castings, flooring, adhesives... [Pg.376]

CAS 21645-51-2 EINECS/ELINCS 244-492-7 Uses Smoke suppressant, flame retardant, filler for PVC and XLPE wire/ cable insulation, SBR compds., epoxies, silicones, elastomers, neoprene foam, vinyl sheet flooring, adhesives, coatings, paints, polishes Pn rerties Superfine powd. 3.5 p avg. particle diam. sp.gr. 2.42 surf, area 8 m /g oil absorp. 32 brightness (TAPPI) 95 ref. index 1.57 hardness (Mohs) 2.5-3.5... [Pg.528]

Methoxy tripropylene glycol acrylate diluent, reactive fiber-reinforced composites Glycidyl ether 100 diluent, reactive floor adhesives N-Vinyl-2-caprolactam diluent, reactive flooring Butyl glycidyl ether... [Pg.5094]

WATER-BASED BINDER SYSTEMS FOR MODERN ENVIRONMENT-FRIENDLY FLOORING ADHESIVES... [Pg.59]

The development of an acrylate polymer emulsion for flooring adhesives, which fulfils the requirements of Emicode, which stipulates that products must be solvent-free and that emissions of individual carcinogenic compounds under standard conditions and 24 hours after application of a product are below defined limiting values, is described. The Tg, total solids content, viscosity and residual monomer content of this acrylic adhesive are tabulated along with the wet tack and shear strength of an optimised binder for flooring adhesives. (2000 World Adhesives Conference Exhibition - Feica)... [Pg.59]

Liquid epoxy resins (Diglycidyl ether of bisphenol A, DGEBA) 2.2 Coatings, castings, tooling, flooring, adhesives, composites... [Pg.2661]

Fig. 101 compares adhesives as per DIN 281 with low-modulus elastic parquet floor adhesives for their tensile shear strength and elongation. [Pg.461]

Figure 101 Position of parquet/timber floor adhesives in the stress-strain diagram.

Flooring adhesives are used for attaching floor coverings to a variety of substrates. The adhesives must develop a strong and durable bond between the floor covering and the substrate. They should not adversely affect coverings, supports and substrates, and after application, should remain odorless and have low emissions. Usually flooring adhesives are applied to the substrate by hand with trowels or sometimes rollers. [Pg.71]

Manufeicturers Comments -62% solids, <5% solvent. Heavy-duty flooring adhesive. Sprayable. Retains bitumen- and PVC-backed floor tiles. [Pg.70]

Manufacturers Comments Multi-purpose flooring adhesive. Manufacturers Comments RT cure. Bonding oily or wax coated as ... [Pg.83]

Manufacturers Comments RT cure. Heavy-duty flooring adhesive, e.g. factory, sports halls and airporte. Internal/external use. High peel and humidity resistance. [Pg.166]

Typical Use Flooring adhesive ruiiber, wood, metal, concrete. [Pg.166]

Manufacturers Comments RT curing. Interior flooring adhesive. ... [Pg.202]

Manufocturers Comments RT cine. High performance flooring adhesive. Internal and external use. High resistance to plasticisers. Impervious to water. High adhesion (peel and shear). [Pg.208]

Building and construction Assembly of structural panels (wood, metal, plastics and insulation materials), laminated panels, assembly of glazing systems, high-duty flooring, adhesive/sealants for woodwork and masonry. [Pg.247]

Manutocturers Comments 98% solids. Flooring adhesive (inc. heated Manutocturers Comments Solvent-free, >99% solids. Thixotropic. ... [Pg.264]

This application uses the vane spindle with a controlled stress rheometer. Vane spindles are useful for low shear measurement of very high-viscosity, near-solid materials. In this case, a heavy flooring adhesive served as the sample. [Pg.32]

Solvent cements of the neoprene or SBR type are used in automotive interiors to fasten roof linings, sound deadener pads, and rubber weatherstripping to doors or door openings. Hot melts of the polyamide type are used as carpet-to-floor adhesives and to anchor instrument gauge springs. [Pg.732]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...