Caustic potash/soda

Hydrazine is generally obtained by reaction in the aqueous phase. It is subsequently concentrated by successive evaporations and rectifications and then, in order to eliminate the water to the maximum extent, one of the methods most recently employed consists in using the dehydrating power of alkaline or alkaline-earth substances, such as caustic soda, potash, or alkaline-earth oxides (quicklime of barium oxide). It is then separated from the dehydrating agent by distillation. 

Biodiesel fuel can be produced from jatropha oil using a fairly simple chemical reaction known as trans-esterification. In this process, the oil reacts with a simple alcohol (methanol/ethanol) in the presence of a catalyst (caustic soda/potash) and, under specified conditions such as a temperature of 65°C and normal atmospheric pressure, yields a mixture of methyl or ethyl esters which is the biodiesel. This fuel... 

Aqueous caustic soda/potash Bromine (at red heat) X X... 

General Chemical Co. Developed by Joseph. A mixture of caustic soda, potash, and vanadium pentoxide added to wet mix of fine kieselguhr, potassium sulfate, and tragacanth gum. Dilute sulfuric acid added to neutralize alkalis. Mixture evaporated before granulation and extrusion. Calcined 600°C. 

Caulks Caustic Caustic baryta Caustic extraction Caustic fusion Caustic magnesia Caustic potash Caustic soda... 

Electrolytic plant producing caustic soda, caustic potash, chlorine, and hydrogen from brine. 

Chlorine Caustic Soda Chlorine Caustic Potash ) Chlorine Sodium Soda Ash ) Chlorine Magnesium Chlorine, Caustic Soda Caustic Potash... 

In a caustic scmbbing system, caustic potash, KOH, is preferred to caustic soda, NaOH, because of the higher solubiUty of the resulting potassium fluoride. Adequate solution contact and residence time must be provided in the scmb tower to ensure complete neutralization of the intermediate oxygen difluoride, OF2. Gas residence times of at least one minute and caustic concentrations in excess of 5% are recommended to prevent OF2 emission from the scmb tower. 

Acids such as sulfuric, hydrochloric, nitric, and especially hydrofluoric as well as strong alkaUes such as caustic soda and caustic potash are extremely corrosive to animal and vegetable tissue. Extreme caution must be taken to prevent skin contact, inhalation, or ingestion. Violent reactions may occur when dissolving or diluting many of these chemicals with water. 

Manufacture, Shipment, and Analysis. In the United States, sodium and potassium thiocyanates are made by adding caustic soda or potash to ammonium thiocyanate, followed by evaporation of the ammonia and water. The products are sold either as 50—55 wt % aqueous solutions, in the case of sodium thiocyanate, or as the crystalline soHds with one grade containing 5 wt % water and a higher assay grade containing a maximum of 2 wt % water. In Europe, the thiocyanates may be made by direct sulfurization of the corresponding cyanide. The acute LD q (rat, oral) of sodium thiocyanate is 764 mg/kg, accompanied by convulsions and respiratory failure LD q (mouse, oral) is 362 mg/kg. The lowest pubhshed toxic dose for potassium thiocyanate is 80—428 mg/kg, with hallucinations, convulsions, or muscular weakness. The acute LD q (rat, oral) for potassium thiocyanate is 854 mg/kg, with convulsions and respiratory failure. 

Inorga.nicNIa.teria.ls. These include acids (sulfuric, nitric, hydrochloric, and phosphoric), bases (caustic soda, caustic potash, soda ash, sodium carbonate, ammonia, and lime), salts (sodium chloride, sodium nitrite, and sodium sulfide) and other substances such as chlorine, bromine, phosphoms chlorides, and sulfur chlorides. The important point is that there is a significant usage of at least one inorganic material in all processes, and the overall toimage used by, and therefore the cost to, the dye industry is high. 

Ammonium hydroxide Potassium hydroxide (caustic potash) Quaternary ammonium hydroxides Sodium hydroxide (caustic soda)... 

Alkali Ammonia Biocides Sodium hydroxide (caustic soda) Potassium hydroxide (caustic potash) Calcium oxide (lime) Calcium hydroxide Sodium, potassium and calcium carbonates Ammonia (q.v.)... 

Evaporators have performed successfully in a number of industrial applications. Typical materials that are processed in evaporators include Caustic Soda, Caustic Potash, Sodium Carbonate, Sodium Dichromate, Sodium Nitrate, Ammonium Nitrate, Phosphoric Acid Superacid, Potash, Urea, Glue, Glycerine,... 

Nitro-filter cloths are composed of cellulose nitrate, which is an ester of cellulose. Any chemical compound that will saponify the ester will destroy the cloth. Caustic soda or potash in strengths of 2% at 70° C or over alkali sulfides, polysulfides and sulfohydrates or mixtures of ethyl alcohol and ether, ethyl, amyl and butyl acetates, pyridine, ferrous sulfates, and other reducing agents are detrimental to the cloth. 

Note The detection is not affected if the dipping solution exhibits a slight opalescent turbidity. Fast blue salt BB [18] or fast blue salt RR [18,19] can be employed in the reagent in place of fast blue salt B. It is occasionally preferable not to apply spray solutions I and II separately but to work directly with a 0.1% solution of fast blue salt B in caustic soda solution (c=l—2mol/l) [13, 15] or in 0.5% methanolic caustic potash [3]. 

It is often possible to increase the detection sensitivity in visible light by exposing the dipped or sprayed chromatogram to ammonia vapors it can also be sprayed with caustic soda or potash solution. When this is done the fluorescence intensity is reduced on silica gel layers and increased on RP ones. 

CATALOX , aluminum oxide, 37 Catalysts Chemicals Division, 211 Catechol, 37 Caustic potash, 37 Caustic soda, 37... 

The amino-acids are not acted on by a hot solution of caustic alkali, but on fusion with caustic soda or potash, yield the amine and CO, ... 

The spectacular success (in 1807) of Humphry Davy, then aged 29 y, in isolating metallic potassium by electrolysis of molten caustic potash (KOH) is too well known to need repeating in detail." Globules of molten sodium were similarly prepared by him a few days later from molten caustic soda. Earlier experiments with aqueous solutions had been unsuccessful because of the great reactivity of these new elements. The names chosen by Davy reflect the sources of the elements. 

Thymol forms a soluble compound with alkalis, and can be extracted from the oils in which it occurs by shaking with a 5 per cent, solution of caustic soda or potash. 

After the furfurel has all been added and the reaction has subsided, the residue is cooled, diluted with water, made strongly alkaline and distilled until all volatile substances are removed. The distillate is then made acid with formic acid and distilled with steam as long as nonbasic substances are carried over by the steam. The residue is then made strongly basic with caustic soda and the volatile amines again distilled with steem. The distillate is then treated with strong alkali and then extracted with ether to extract the base. The extract is dried by the addition of caustic potash, the ether removed and the residual amine purified by distillation. Furfuryl dimethyl amine boils over the range 145°C to 150°C. 

B.5 parts of 1 -azaphenothiazine carboxylic acid chloride and 14 parts of piperidino-ethoxy-ethanol were introduced into 100 parts of chlorobenzene and the mixture boiled under reflux for 5 minutes. After cooling off the precipitated hydrochloride salt of piperidino-ethoxy-ethanol was filtered off on a suction filter. Water was added to the filtrate and the pH thereof adjusted to 5 to 6 with dilute HCI. The aqueous phase was then removed, a caustic soda solution added thereto and then extracted with ether. The ethyl extract waswashed with water, then dried with potash and the ether distilled off. 9.4 parts of the piperidino-ethoxy-ethyi ester of 1 -azaphenothiazine carboxylic acid were obtained. This product was dissolved in 20 parts of isopropanol and the solution neutralized with isopropanolic HCI. The monohydrochloride which precipitated out after recrystallization from isopropanol had a melting point of 160°Cto 161°C. 

In this section, chemical resistance will be divided into three parts, viz. acid, alkali (including detergents) and water (including atmosphere). Normally an enamel is formulated to withstand one of the corrosive agents more specifically than another, although vitreous enamel as a general finish has good all round resistance, with a few exceptions such as hydrofluoric acid and fused or hot concentrated solutions of caustic soda or potash. 

Sodium hydroxide (NaOH) (caustic soda) Potassium hydroxide (KOH) (caustic potash) Calcium hydroxide (Ca(OH)2) (slaked lime) Ammonium hydroxide (NH4OH) (aqueous ammonia solution) White deliquescent solid. Sticks, flakes, pellets. Dissolution in water is highly exothermic. Strongly basic. Severe hazard to skin tissue White deliquescent solid. Sticks, flakes, pellets. Dissolution In water is highly exothermic. Strongly basic. Severe hazard to skin tissue White powder soluble in water yielding lime water. Alkaline Weakly alkaline. Emits ammonia gas. Severe eye irritant... 

---