Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Analytical methods elemental analysis

Among other methods for determining trace and toxic elements in the soil, there are also electro-chemical analytical methods, mainly polarogra-phy and in the case of nuclear analytical methods, activation analysis and radionuclide X-ray fluorescence analysis are employed. Mass spectrometry, laser emission spectral microanalysis and other instrumental methods can also be used. [Pg.696]

The absolute quantities of elements contained in both the soluble and insoluble fractions were determined by particle induced X-ray emission (PIXE) analytical method. PIXE analysis was performed with a proton beam of a 6 mm diameter and a 2.0 MeV energy from a Tandem Cockcroft accelerator installed at the Quantum Science and Engineering Center of Kyoto University. Beam intensities from 10 to 60 nA were employed, and the total dose was about 20 pC. An X-ray with an energy of up to 14.8 keV emitted from the target was detected by a Si (Li) detector with a resolution of 152 eV at 5.9 keV. The calibration method of PIXE was similar to that described elsewhere (Kasahara et al. 1993) and is described here briefly. The relationship of an X-ray yield and the mass thickness was measured first using the 18 single element standard samples prepared by a vacuum... [Pg.374]

As an analytical method activation analysis determines the concentration of an elemental component of a sample material by inducing radioactivity in an isotope, or isotopes, of that element by means of a nuclear particle bombardment. The detection and measurement of the... [Pg.347]

Typically, PIXE measurements are perfonned in a vacuum of around 10 Pa, although they can be perfonned in air with some limitations. Ion currents needed are typically a few nanoamperes and current is nonnally not a limiting factor in applying the teclmique with a particle accelerator. This beam current also nonnally leads to no significant damage to samples in the process of analysis, offering a non-destmctive analytical method sensitive to trace element concentration levels. [Pg.1843]

Perhaps the most common type of problem encountered in the analytical lab is a quantitative analysis. Examples of typical quantitative analyses include the elemental analysis of a newly synthesized compound, measuring the concentration of glucose in blood, or determining the difference between the bulk and surface concentrations of Cr in steel. Much of the analytical work in clinical, pharmaceutical, environmental, and industrial labs involves developing new methods for determining the concentration of targeted species in complex samples. Most of the examples in this text come from the area of quantitative analysis. [Pg.9]

There are many potential advantages to kinetic methods of analysis, perhaps the most important of which is the ability to use chemical reactions that are slow to reach equilibrium. In this chapter we examine three techniques that rely on measurements made while the analytical system is under kinetic rather than thermodynamic control chemical kinetic techniques, in which the rate of a chemical reaction is measured radiochemical techniques, in which a radioactive element s rate of nuclear decay is measured and flow injection analysis, in which the analyte is injected into a continuously flowing carrier stream, where its mixing and reaction with reagents in the stream are controlled by the kinetic processes of convection and diffusion. [Pg.622]

Analytical Methods. Most analytical methods use the oxidizing power of iodine for its deterrnination. The results are generaHy expressed as an equivalent concentration of elemental iodine. The choice of a method for the analysis of iodine depends on the concentration range to be deterrnined. [Pg.364]

Analytical Methods. Molybdenum contents in ore concentrates and technical oxide are most accurately deterrnined gravimetricaHy by precipitating lead molybdate. Molybdenum content is usually not determined on pure compounds or metal. Instead, spectrographic methods are used to measure impurity elements that must be controlled. Carbon and oxygen in metal products are measured by standard gas analysis methods. [Pg.463]

Chemical Properties. Elemental analysis, impurity content, and stoichiometry are determined by chemical or iastmmental analysis. The use of iastmmental analytical methods (qv) is increasing because these ate usually faster, can be automated, and can be used to determine very small concentrations of elements (see Trace AND RESIDUE ANALYSIS). Atomic absorption spectroscopy and x-ray fluorescence methods are the most useful iastmmental techniques ia determining chemical compositions of inorganic pigments. Chemical analysis of principal components is carried out to determine pigment stoichiometry. Analysis of trace elements is important. The presence of undesirable elements, such as heavy metals, even in small amounts, can make the pigment unusable for environmental reasons. [Pg.4]

Only slightly less accurate ( 0.3—0.5%) and more versatile in scale are other titration techniques. Plutonium maybe oxidized in aqueous solution to PuO " 2 using AgO, and then reduced to Pu" " by a known excess of Fe", which is back-titrated with Ce" ". Pu" " may be titrated complexometricaHy with EDTA and a colorimetric indicator such as Arsenazo(I), even in the presence of a large excess of UO " 2- Solution spectrophotometry (Figs. 4 and 5) can be utilized if the plutonium oxidation state is known or controlled. The spectrophotometric method is very sensitive if a colored complex such as Arsenazo(III) is used. Analytically usehil absorption maxima and molar absorption coefficients ( s) are given in Table 10. Laser photoacoustic spectroscopy has been developed for both elemental analysis and speciation (oxidation state) at concentrations of lO " — 10 M (118). Chemical extraction can also be used to enhance this technique. [Pg.200]

Comprehensive accounts of the various gravimetric, polarographic, spectrophotometric, and neutron activation analytical methods have been pubHshed (1,2,5,17,19,65—67). Sampling and analysis of biological materials and organic compounds is treated in References 60 and 68. Many analytical methods depend on the conversion of selenium in the sample to selenous acid, H2Se02, and reduction to elemental selenium when a gravimetric deterrnination is desired. [Pg.335]

The complex of the following destmctive and nondestmctive analytical methods was used for studying the composition of sponges inductively coupled plasma mass-spectrometry (ICP-MS), X-ray fluorescence (XRF), electron probe microanalysis (EPMA), and atomic absorption spectrometry (AAS). Techniques of sample preparation were developed for each method and their metrological characteristics were defined. Relative standard deviations for all the elements did not exceed 0.25 within detection limit. The accuracy of techniques elaborated was checked with the method of additions and control methods of analysis. [Pg.223]

If the secondary ion component is indeed negligible, the measured SNMS ion currents will depend only on the ionizing mode, on the atomic properties of the sputtered atoms, and on the composition of the sputtered sample. Matrix characteristics will have no effect on the relative ion currents. SNMS analysis also provides essentially complete coverage, with almost all elements measured with equal facility. All elements in a chemically complex sample or thin-film structure will be measured, with no incompleteness due to insensitivity to an important constituent element. Properly implemented SNMS promises to be a near-universal analytical method for solids analysis. [Pg.573]

If the critical impurities are known, then only a selected list of elements need to be examined, with some improvement in the cost effectiveness of the analysis. However, the list of elements to be included in the qualification analysis is often historical and related to the limitations of the analytical methods previously used for qualification rather than for technological reasons related to the end use of the metal. As a result, problems in application can arise for no obvious reason. The time and cost of extending the impurity list for GDMS analysis to include essentially all elements is minimal, considering the additional information gained. [Pg.621]

Because of the complex nature of the discharge conditions, GD-OES is a comparative analytical method and standard reference materials must be used to establish a unique relationship between the measured line intensities and the elemental concentration. In quantitative bulk analysis, which has been developed to very high standards, calibration is performed with a set of calibration samples of composition similar to the unknown samples. Normally, a major element is used as reference and the internal standard method is applied. This approach is not generally applicable in depth-profile analysis, because the different layers encountered in a depth profile of ten comprise widely different types of material which means that a common reference element is not available. [Pg.225]

Table 8 shows results obtained from the application of various bulk and surface analysis methods to lithium metal at rest or after cyclization experiments, as well as at inert and carbon electrodes after cathodic polarization. The analytical methods include elemental analysis, X-ray photoelectron spectroscopy (XPS or ESCA), energy-dispersive analysis of X-rays (X-ray mi-... [Pg.481]

In this chapter we have limited ourselves to the most common techniques in catalyst characterization. Of course, there are several other methods available, such as nuclear magnetic resonance (NMR), which is very useful in the study of zeolites, electron spin resonance (ESR) and Raman spectroscopy, which may be of interest for certain oxide catalysts. Also, all of the more generic tools from analytical chemistry, such as elemental analysis, UV-vis spectroscopy, atomic absorption, calorimetry, thermogravimetry, etc. are often used on a routine basis. [Pg.166]

In contrast to the well-established methods for identifying and quantifying naturally occurring chlorophylls, very few reports concern quantitative analysis of chlorophyllin copper complexes in color additives and in foodstuffs. Analytical methods proposed are based on spectral properties, elemental analysis, chromatographic separation, and molecular structure elucidation or a combination of these procedures. [Pg.442]

Since we are interested in evaluating structure-activity relationships (see Sect. 2.2), it is important to combine several analytical methods to allow a characterization at a molecular level for example, elemental analysis, IR, and advanced NMR spectroscopies, EXAFS and chemical reactivity studies. [Pg.169]

The apphed pretreatment techniques were digestion with a combination of acids in the pressurized or atmospheric mode, programmed dry ashing, microwave digestion and irradiation with thermal neutrons. The analytical methods of final determination, at least four different for each element, covered all modern plasma techniques, various AAS modes, voltammetry, instrumental and radiochemical neutron activation analysis and isotope dilution MS. Each participating laboratory was requested to make a minimum of five independent rephcate determinations of each element on at least two different bottles on different days. Moreover, a series of different steps was undertaken in order to ensure that no substantial systematic errors were left undetected. [Pg.65]

How critically interdependent matrix and analytical methods can be is illustrated in the example of the analysis of a soil sample. Table 7.1 shows the method dependent certified values for some common trace elements. The soil had been subjected to a multi-national, multi-laboratory comparison on a number of occasions (Houba et al. 1995) which provided extensive data. The data was subjected to a rigorous statistical program, developed for the USEPA by Kadafar (1982). This process allowed the calculation of certified values for a wide range of inorganic analytes. Uniquely, for the soil there are certified values for four very different sample preparation methods, as follows ... [Pg.239]

Although elemental analysis (i.e. the determination of elements ranging from H to U) in a polymeric material is very common practice in the polymer industry, among polymer processors, research and application laboratories, and end-users, the analytical methods and protocols used are widely different and are not harmonised within the EC, let alone worldwide. Among the currently established 344 ISO methods for plastics, there are no ISO-approved methods available for... [Pg.587]


See other pages where Analytical methods elemental analysis is mentioned: [Pg.249]    [Pg.260]    [Pg.249]    [Pg.260]    [Pg.365]    [Pg.330]    [Pg.1530]    [Pg.277]    [Pg.50]    [Pg.276]    [Pg.116]    [Pg.419]    [Pg.243]    [Pg.52]    [Pg.71]    [Pg.118]    [Pg.133]    [Pg.347]    [Pg.622]    [Pg.33]    [Pg.84]    [Pg.285]    [Pg.4]    [Pg.61]    [Pg.66]    [Pg.218]    [Pg.223]    [Pg.227]    [Pg.45]    [Pg.35]    [Pg.588]   


SEARCH



Analytical Analyses

Element analytical methods

© 2024 chempedia.info