Advantages, potential

The potential advantages of LPG concern essentially the environmental aspects. LPG s are simple mixtures of 3- and 4-carbon-atom hydrocarbons with few contaminants (very low sulfur content). LPG s contain no noxious additives such as lead and their exhaust emissions have little or no toxicity because aromatics are absent. This type of fuel also benefits often enough from a lower taxation. In spite of that, the use of LPG motor fuel remains static in France, if not on a slightly downward trend. There are several reasons for this situation little interest from automobile manufacturers, reluctance on the part of automobile customers, competition in the refining industry for other uses of and fractions, (alkylation, etherification, direct addition into the gasoline pool). However, in 1993 this subject seems to have received more interest (Hublin et al., 1993). 

Horizontal wells were drilled as far back as the 1950s, but have gained great popularity in the last decade, as lower oil prices have forced companies to strive for technologies which reduce the cost of oil and gas recovery. Horizontal wells have potential advantage over vertical or deviated wells for three main reasons ... 

A potential advantage of methods based on a series expansion of the free energy is that the convergence of the series is determined by the A dependence of the potential energy function meaning that the efficiency of the approach could be enhanced by a judicious choice of coupling scheme. 

There are many potential advantages to kinetic methods of analysis, perhaps the most important of which is the ability to use chemical reactions that are slow to reach equilibrium. In this chapter we examine three techniques that rely on measurements made while the analytical system is under kinetic rather than thermodynamic control chemical kinetic techniques, in which the rate of a chemical reaction is measured radiochemical techniques, in which a radioactive element s rate of nuclear decay is measured and flow injection analysis, in which the analyte is injected into a continuously flowing carrier stream, where its mixing and reaction with reagents in the stream are controlled by the kinetic processes of convection and diffusion. 

Hbls Process. Chemische Werke Huls AG has developed a process to produce soda ash and hydrochloric acid from salt via an amine—solvent system (12). A potential advantage of the Huls process is that, under some market conditions, hydrochloric acid may be more easily sold than either ammonium or calcium chloride. 

Chromium. Chromium offers a number of potential advantages for high temperature appHcations, including oxidation resistance, low density, and a melting point over 400°C higher than that of nickel. Nevertheless, all efforts to use chromium have been hindered by its extreme brittieness (58). 

Use of traveling wave tube (TWT) amplifiers at power levels of hundreds of watts has been proposed (54) for power appHcations, at least when the heating chamber is well shielded. The potential advantage is an improved uniformity of heating when a broad band of frequency is used, ie, excitation of many modes. Disadvantages are high cost and lower (<50%) efficiency of the TWT. 

Single-crystal siHcon can also be grown from various fluxes and by a combination of electrolysis and fluxes at temperatures weU below the melting point of pure siHcon (16). The main disadvantages are the inclusion of the flux in the crystal and the poor crystal quaHty. Potential advantages are a decrease in growth temperature and purification during electrolysis. 

In recent years, several wet milling operations have been initiated with obvious advantages in dust control and potential advantages in the separation of mineral contaminants from the fiber product. On the other hand, large-scale industrial wet classification methods are not in use at present. 

Numerical simulations offer several potential advantages over experimental methods for studying dynamic material behavior. For example, simulations allow nonintrusive investigation of material response at interior points of the sample. No gauges, wires, or other instrumentation are required to extract the information on the state of the material. The response at any of the discrete points in a numerical simulation can be monitored throughout the calculation simply by recording the material state at each time step of the calculation. Arbitrarily fine resolution in space and time is possible, limited only by the availability of computer memory and time. 

Potential advantages of this route are the ability to use a mixed feedstock and the fact that hydrochloric acid formed in one part of the process may be used in the other part. 

Artificial Neural Networks have the following potential advantages for intelligent control ... 

It is seen that the curves in Figure (24) become horizontal between 40°C and 45 °C as predicted by the theory. It is also clear that there is likely source of error when exploring the effect of solvent composition on retention and selectivity. It would be important when evaluating the effect of solvent composition on selectivity to do so over a range of temperatures. This would ensure that the true effect of solvent composition on selectivity was accurately disclosed. If the evaluation were carried out at or close to the temperature where the separation ratio remains constant and independent of solvent composition, the potential advantages that could be gained from an optimized solvent mixture would never be realized. 

Do you see the potential advantage of P2 over an end-of-pipe treatment option ... 

A potential advantage of the Schmidt reaction is illustrated by the conversion of progesterone to the 17j5-acetylamino derivative, without affecting the A-ring. A 35 % yield is obtained when 1 mole of sodium azide in polyphos-phoric acid is used. With excess azide the A-ring is transformed into an a,jS-unsaturated lactam ... 

THE WHY — CURRENT AND POTENTIAL ADVANTAGES OPPISER-REINFOReED OMPOSITtMATERIALS... 

The basic nature of composite materials was introduced in Chapter 1. An overall classification scheme was presented, and the mechanical behavior aspects of composite materials that differ from those of conventional materials were described in a qualitative fashion. The book was then restricted to laminated fiber-reinforced composite mafeffals. The basic definitions and how such materials are made were then treated. Finally, the current and potential advantages of composite materials were discussed along with some case histories that clearly reveal how composite materials are used in structures. 

With the advent of notebook computers, it is feasible to use interactive software to structure the data collection process at the workplace. There are many potential advantages with this approach. 

Thanks to their special properties and potential advantages, ionic liquids may be interesting solvents for biocatalytic reactions to solve some of the problems discussed above. After initial trials more than 15 years ago, in which ethylammonium nitrate was used in salt/water mixtures [29], results from the use of ionic liquids as pure solvent, as co-solvent, or for biphasic systems have recently been reported. The reaction systems are summarized in Tables 8.3-1 and 8.3-2, below. Table 8.3-1 compiles all biocatalytic systems except lipases, which are shown separately in 8.3-2. Some of the entries are discussed in more detail below. 

Potential advantages of both thermoplastics and cellu-losic materials combined with the economic and environmental viewpoint have lead to a promising utilization of both these materials in various forms of composites. Although various branches of cellulosic-thermoplastic composites industries are booming in recent years, their growth rate is very slow. In order to achieve the full potential of such valuable materials as various engineering materials and commodity products more incentives from academic, industrial, and governmental authorities are needed. 

In this process, resin is injected into a closed mold containing the reinforcement preform. The resin can be injected either under pressure [22] or under vacuum [23]. The potential advantages of this process are (I) low mold cost, (2) inserts can be incorporated, (3) low pressure requirements, (4) accurate fiber orientation, (5) automation possibilities, and (6) versatility. The resin formulation and process variables are selected so that no significant polymerization occurs until the mold cavity has been completely filled. This is achieved by the ad-... 

Despite a strong awareness of the potential advantages of district heating in the early nineteenth century, widespread adoption did not occur until technology was developed to handle the numerous problems associated with heat distribution. The Great... 

Other fusion reactions such as D plus "He" and D plus D (not to mention the II plus II of stars) require far more difficult physical conditions than D plus T, but offer potential advantages in reduced neutron production, and even larger reseiwes of potential energy in the case of D-D. 

---