Vinyl ethylene copolymer

Vinyl acetate-fatty acid vinyl ethylene copolymer... 

Low-density Medium-density High-density Ultra high-molecular-weight Glass-fiber- reinforced, high-density Ethylene-vinyl acetate copolymer... 

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

Perfluorinated ethylene—propylene copolymers, Tetrafluoroethylene—ethylene copolymers, Tetrafluoroethylene—perfluorovinyl ether copolymers, Poly(vinyl fluoride),... 

Ethylene vinyl acetate copolymer (EVA) forms a soft, tacky film with good water-vapor barrier but very poor gas-barrier properties. It is widely used as a low temperature initiation and broad-range, heat-sealing medium. The film also serves for lamination to other substrates for heat-sealing purposes. 

Thermoform able sheet may be mono- or multilayer with the latter produced by lamination or coextmsion. Multilayers are employed to incorporate high oxygen-barrier materials between stmctural or high water-vapor barrier plastics. Both ethylene vinyl alcohol copolymers and poly(vinyhdene chloride) (less often) are used as high oxygen-barrier interior layers with polystyrene or polypropylene as the stmctural layers, and polyolefin on the exterior for sealing. 

Hydrocarbon resins (qv) are prepared by copolymerization of vinyltoluene, styrene, and a-methylstyrene in the presence of a Eriedel-Crafts catalyst (AlCl ). These resins are compatible with wax and ethylene—vinyl acetate copolymer (197). 

Many synthetic latices exist (7,8) (see Elastomers, synthetic). They contain butadiene and styrene copolymers (elastomeric), styrene—butadiene copolymers (resinous), butadiene and acrylonitrile copolymers, butadiene with styrene and acrylonitrile, chloroprene copolymers, methacrylate and acrylate ester copolymers, vinyl acetate copolymers, vinyl and vinyUdene chloride copolymers, ethylene copolymers, fluorinated copolymers, acrylamide copolymers, styrene—acrolein copolymers, and pyrrole and pyrrole copolymers. Many of these latices also have carboxylated versions. 

Organic peroxides are used in the polymer industry as thermal sources of free radicals. They are used primarily to initiate the polymerisation and copolymerisation of vinyl and diene monomers, eg, ethylene, vinyl chloride, styrene, acryUc acid and esters, methacrylic acid and esters, vinyl acetate, acrylonitrile, and butadiene (see Initiators). They ate also used to cute or cross-link resins, eg, unsaturated polyester—styrene blends, thermoplastics such as polyethylene, elastomers such as ethylene—propylene copolymers and terpolymers and ethylene—vinyl acetate copolymer, and mbbets such as siUcone mbbet and styrene-butadiene mbbet. 

Fig. 10. Preparation and morphology of toughened PVC (a) secondary PVC grain (50—250 flm) (b) modified PVC with coherent primary grain (ca 1 -lm) (220). CPE = chlorinated polyethylene EVA = ethylene—vinyl acetate copolymers ABS = acrylonitrile—butadiene—styrene MBS = methyl...

Small amounts of TAIC together with DAP have been used to cure unsaturated polyesters in glass-reinforced thermo sets (131). It has been used with polyfunctional methacrylate esters in anaerobic adhesives (132). TAIC and vinyl acetate are copolymerized in aqueous suspension, and vinyl alcohol copolymer gels are made from the products (133). Electron cure of poly(ethylene terephthalate) moldings containing TAIC improves heat resistance and transparency (134). 

Pubhcations on curing polymers with TAIC include TEE—propylene copolymer (135), TEE—propylene—perfluoroaHyl ether (136), ethylene—chlorotrifluoroethylene copolymers (137), polyethylene (138), ethylene—vinyl acetate copolymers (139), polybutadienes (140), PVC (141), polyamide (142), polyester (143), poly(ethylene terephthalate) (144), sdoxane elastomers (145), maleimide polymers (146), and polyimide esters (147). 

Substituted amides (not of the alkanolamide variety) are sold to diverse low volume markets. They have some utility ki polymers such as polyethylene, ethylene-vinyl acetate copolymers, acryUc polymers, PVC, polyamides, and polyesters. They have been found effective as pharmaceutical processkig aids, defoamers (qv), antimicrobials, pesticides, kisect repellents, dispersion stabilizers, and corrosion inhibitors. 

Rosin, modified rosins, and derivatives are used in hot-melt adhesives. They are based primarily on ethylene—vinyl acetate copolymers. The rosin derivative is used in approximately a 1 1 1 concentration with the polymer and a wax. The resin provides specific adhesion to the substrates and reduces the viscosity at elevated temperatures, allowing the adhesive to be appHed as a molten material. 

Vinyl Acetate—Ethylene Copolymers. In these random copolymers, the ratio of ethylene to vinyl acetate (EVA) is varied from 30—60%. As the vinyl acetate content increases, the oil and heat resistance increases. With higher ethylene content the physical strength, tensile, and tear increases. The polymers are cured with peroxide. The main properties of these elastomers include heat resistance, moderate oil and solvent resistance, low compression set, good weather resistance, high damping, exceUent o2one resistance, and they can be easily colored (see Vinyl polymers, poly(VINYL acetate)). 

Materials are also blended with VDC copolymers to improve toughness (211—214). VinyHdene chloride copolymer blended with ethylene—vinyl acetate copolymers improves toughness and lowers heat-seal temperatures (215,216). Adhesion of a VDC copolymer coating to polyester can be achieved by blending the copolymer with a linear polyester resin (217). 

The nmr spectmm of PVAc iu carbon tetrachloride solution at 110°C shows absorptions at 4.86 5 (pentad) of the methine proton 1.78 5 (triad) of the methylene group and 1.98 5, 1.96 5, and 1.94 5, which are the resonances of the acetate methyls iu isotactic, heterotactic, and syndiotactic triads, respectively. Poly(vinyl acetate) produced by normal free-radical polymerization is completely atactic and noncrystalline. The nmr spectra of ethylene vinyl acetate copolymers have also been obtained (33). The ir spectra of the copolymers of vinyl acetate differ from that of the homopolymer depending on the identity of the comonomers and their proportion. 

Continuous emulsion copolymerization processes for vinyl acetate and vinyl acetate—ethylene copolymer have been reported (59—64). CycHc variations in the number of particles, conversion, and particle-size distribution have been studied. Control of these variations based on on-line measurements and the use of preformed latex seed particles has been discussed (61,62). 

The low vinyl acetate ethylene—vinyl acetate copolymers, ie, those containing 10—40 wt % vinyl acetate, are made by processes similar to those used to make low density polyethylene for which pressures are usually > 103 MPa (15,000 psi). A medium, ie, 45 wt % vinyl acetate copolymer with mbber-like properties is made by solution polymerisation in /-butyl alcohol at 34.5 MPa (5000 psi). The 70—95 wt % vinyl acetate emulsion copolymers are made in emulsion processes under ethylene pressures of 2.07—10.4 MPa (300—1500 psi). 

Poly(ethyl methacrylate) (PEMA) yields truly compatible blends with poly(vinyl acetate) up to 20% PEMA concentration (133). Synergistic improvement in material properties was observed. Poly(ethylene oxide) forms compatible homogeneous blends with poly(vinyl acetate) (134). The T of the blends and the crystaUizabiUty of the PEO depend on the composition. The miscibility window of poly(vinyl acetate) and its copolymers with alkyl acrylates can be broadened through the incorporation of acryUc acid as a third component (135). A description of compatible and incompatible blends of poly(vinyl acetate) and other copolymers has been compiled (136). Blends of poly(vinyl acetate) copolymers with urethanes can provide improved heat resistance to the product providing reduced creep rates in adhesives used for vinyl laminating (137). 

Special vinyl acetate copolymer paints have been developed with gready improved resistance to blistering or peeling when immersed in water. This property allows better cleaning and use in very humid environments. These lattices exhibit the water resistance of higher priced acryUc resins (150). VAc, vinyl chloride—ethylene terpolymers have been developed which provide the exterior resistance properties of vinyl chloride with the dexibiUty of the ethylene for exterior paint vehicles (151). 

In contrast to other polymers the resistance to water permeation is low due to the hydrolysis of the poly(vinyl acetate) (163,164). Ethylene copolymers have been developed which have improved water resistance and waterproofness. The polymer can be used in the latex form or in a spray-dried form which can be preblended in with the cement (qv) in the proper proportion. The compressive and tensile strength of concrete is improved by addition of PVAc emulsions to the water before mixing. A polymer-soHds-to-total-soHds ratio of ca 10 90 is best. The emulsions also aid adhesion between new and old concrete when patching or resurfacing. 

Ce = cellulosics, EVA = ethylene-vinyl acetate copolymers, F = foods, GAS = gasoline, LUB = lubricants, PA = polyamides, PES = polyesters,... 

---