Physical strength

Railroads also require coarse and fine aggregate of physical strength and durabiHty similar to concrete and roadstone for road beds. Railroads prefer gradation of 19—63.5 mm as coarse aggregate. 

Refractories are materials that resist the action of hot environments by containing heat energy and hot or molten materials (1). There is no weU-estabhshed line of demarcation between those materials that are and those that are not refractory. The abiUty to withstand temperatures above 1100°C without softening has, however, been cited as a practical requirement of industrial refractory materials (see Ceramics). The type of refractories used in any particular apphcation depends on the critical requirements of the process. For example, processes that demand resistance to gaseous orHquid corrosion require low permeabihty, high physical strength, and abrasion resistance. Conditions that demand low thermal conductivity may require entirely different refractories. Combinations of several refractories are generally employed. 

Nittile mbber is much like SBR in its physical properties. It can be compounded for physical strength and abrasion resistance using traditional fillers such as carbon black, siUca, and reinforcing clays. The primary benefit of the polymer is its oil and solvent resistance. At a medium ACN content of 34% the swell in IRM 903 oil at 70°C is typically 25—30%. Nitrile mbber processes on conventional mbber equipment and can be compression, transfer, or injection molded. It can also be extmded easily. 

Vinyl Acetate—Ethylene Copolymers. In these random copolymers, the ratio of ethylene to vinyl acetate (EVA) is varied from 30—60%. As the vinyl acetate content increases, the oil and heat resistance increases. With higher ethylene content the physical strength, tensile, and tear increases. The polymers are cured with peroxide. The main properties of these elastomers include heat resistance, moderate oil and solvent resistance, low compression set, good weather resistance, high damping, exceUent o2one resistance, and they can be easily colored (see Vinyl polymers, poly(VINYL acetate)). 

Reactants must diffuse through the network of pores of a catalyst particle to reach the internal area, and the products must diffuse back. The optimum porosity of a catalyst particle is deterrnined by tradeoffs making the pores smaller increases the surface area and thereby increases the activity of the catalyst, but this gain is offset by the increased resistance to transport in the smaller pores increasing the pore volume to create larger pores for faster transport is compensated by a loss of physical strength. A simple quantitative development (46—48) follows for a first-order, isothermal, irreversible catalytic reaction in a spherical, porous catalyst particle. 

Transition aluminas are good catalyst supports because they are inexpensive and have good physical properties. They are mechanically stable, stable at relatively high temperatures even under hydrothermal conditions, ie, in the presence of steam, and easily formed in processes such as extmsion into shapes that have good physical strength such as cylinders. Transition aluminas can be prepared with a wide range of surface areas, pore volumes, and pore size distributions. 

Binders. To create needed physical strength in catalysts, materials called binders are added (51) they bond the catalyst. A common binder material is a clay mineral such as kaolinite. The clay is added to the mixture of microparticles as they are formed into the desired particle shape, for example, by extmsion. Then the support is heated to remove water and possibly burnout material and then subjected to a high temperature, possibly 1500°C, to cause vitrification of the clay this is a conversion of the clay into a glasslike form that spreads over the microparticles of the support and binds them together. 

Unfilled Tooth Restorative Resins. UnfiUed reskis were some of the first polymer materials iatroduced to repak defects ki anterior teeth where aesthetics were of concern. They have been completely replaced by the fiUed composite reskis that have overcome the problems of poor color StabUity, low physical strength, high volume shrinkage, high thermal expansion, and low abrasion resistance commonly associated with unfiUed reskis. 

Another significant end-use for polyamines is in preparation of paper wet-strength resins. These are polyamide, modified formaldehyde, and polyamine resins used to improve the physical strength of tissue, toweling, and packaging paper products. The cationic formaldehyde resins include both urea—formaldehyde and melamine—formaldehyde types (248,249). Cationic functionaHty is imparted by incorporation of DETA, TETA, and/or TEPA in... 

Various methods are used for evaluatiag the quaflty, ie, physical strength and ensyme dust formation, of the granulate. In the elutriation process, a sample of product is fluidised ia a glass tube with a perforated bottom plate for 40 miautes. Dust from the sample is collected oa a filter and the ensyme activity measured. An acceptable dust level is when less than 5—10 ppm of the activity of the sample has been collected. In the so-called Heubach method, 20 g of granulate is elutriated. During the elutriation, four steel balls are rotated ia the bed ia order to evaluate the impact of attritioa oa the dust release of the ensyme. The dust is collected oa a filter and measured. The acceptable dust level is very low. 

Perfhioroalko] (Teflon) (PFA) was introduced in 1972 and is a fully fluorinated polymer that is melt-processible with better melt flow and molding properties than the FEP. The PFA has excellent resistance to chemicals. It can withstand acids as well as caustic materials. PFA has better mechanical properties than FEP above 300°F (149°C) and can be used up to 500°F (260°C) for some applications. The low physical strength and high cost of this polymer limit use for some applications. 

---