Selectivity in reactors

Product safety regulations, 27 590-592 Product selectivity, in reactor technology, 27 338... 

M. Feinberg and P. EUison. General kinetic bounds on productivity and selectivity in reactor-separator systems of arbitrary design I. Principles. Ind. Eng. Chem. Res., 40fl4) 3181-3194, 2001. 

On the other hand, studying the influence of the surface material on the DMTM process in one [140] of a series of works, where a very high selectivity of methanol formation (P = 30 atm, T = 350 °C, tj- > 100 s) was observed, revealed no significant differences in the selectivity and yield of methanol in reactors with different surfaces, such as Pyrex, Teflon, stainless steel, silver, and copper. In these experiments, the selectivity of methanol formation on all surfaces reached values close to 90% or more, whereas the methanol yield was as high as 10.7%. However, the authors do not exclude the possibility of influence of the surface material on the temperature and reaction time. In particular, it was found that the maximum selectivity in reactors with metal surfaces was achieved at temperatures higher by nearly 50 °C. This is probably due to the fact that, at lower temperatures in the presence of a metal surface, the oxidation occurs mostly in the heterogeneous mode with the formation of mainly deep-oxidation products. 

The selection of reactor pressure for vapor-phase reversible reactions depends on whether there is a decrease or increase in the number of moles and whether there is a system of single or multiple reactions. 

In Chap. 2 the objective set was to maximize selectivity for a given conversion. This also will minimize waste generation in reactors for a given conversion. 

Increasing process yields of raw materials through improved selectivity in the reactor. 

Vanadium phosphoms oxide-based catalysts ate unstable in that they tend to lose phosphoms over time at reaction temperatures. Hot spots in fixed-bed reactors tend to accelerate this loss of phosphoms. This loss of phosphoms also produces a decrease in selectivity (70,136). Many steps have been taken, however, to aHeviate these problems and create an environment where the catalyst can operate at lower temperatures. For example, volatile organophosphoms compounds are fed to the reactor to mitigate the problem of phosphoms loss by the catalyst (137). The phosphoms feed also has the effect of controlling catalyst activity and thus improving catalyst selectivity in the reactor. The catalyst pack in the reactor may be stratified with an inert material (138,139). Stratification has the effect of reducing the extent of reaction pet unit volume and thus reducing the observed catalyst temperature (hot... 

The methyl a-hydroxyisobutyrate produced is dehydrated to MMA and water in two stages. First, the methyl a-hydroxyisobutyrate is vaporized and passed over a modified zeoHte catalyst at ca 240°C. A second reactor containing phosphoric acid is operated at ca 150°C to promote esterification of any methacrylic acid (MAA) formed in the first reactor (74,75). Methanol is co-fed to improve selectivity in each stage. Conversions of methyl a-hydroxyisobutyrate are greater than 99%, with selectivities to MMA near 96%. The reactor effluent is extracted with water to remove methanol and yield cmde MMA. This process has not yet been used on a commercial scale. 

Additional Selection Factors. System characteristics and physical and chemical properties can be principal considerations in reactor... 

Distributors in industrial units typically have large numbers of injection points of quite diverse design characteristics, some of which are depicted in Eigure 16 for fluidized-bed appHcations. Flow variations through these parallel paths can lead to poor flow distributions within a reactor, thus reducing product yields and selectivity. In some circumstances, undesirable side products can foul portions of the distributor and further upset flow patterns. Where this is important, or where the possibiHties and consequences are insufficiently understood and independent means caimot be employed to assure adequate distribution, the pilot plant must be sized to accommodate such a distributor. Spacing should be comparable to those distributors that are anticipated to be... 

One goal of catalyst designers is to constmct bench-scale reactors that allow determination of performance data truly indicative of performance in a full-scale commercial reactor. This has been accompHshed in a number of areas, but in general, larger pilot-scale reactors are preferred because they can be more fully instmmented and can provide better engineering data for ultimate scale-up. In reactor selection thought must be given to parameters such as space velocity, linear velocity, and the number of catalyst bodies per reactor diameter in order to properly model heat- and mass-transfer effects. 

The reactor has been successfully used in the case of forced precipitation of copper and calcium oxalates (Jongen etal., 1996 Vacassy etal., 1998 Donnet etal., 1999), calcium carbonate (Vacassy etal., 1998) and mixed yttrium-barium oxalates (Jongen etal., 1999). This process is also well adapted for studying the effects of the mixing conditions on the chemical selectivity in precipitation (Donnet etal., 2000). When using forced precipitation, the mixing step is of key importance (Schenk etal., 2001), since it affects the initial supersaturation level and hence the nucleation kinetics. A typical micromixer is shown in Figure 8.35. 

There is a steady flow of publication which contributes theories and information to help in the choice of catalysts, the improvement of their selectivity, or the improvement in reactor utilization through increase in... 

Catalytic reactors can roughly be classified as random and structured reactors. In random reactors, catalyst particles are located in a chaotic way in the reaction zone, no matter how carefully they are packed. It is not surprising that this results in a nonuniform fiow over the cross-section of the reaction zone, leading to a nonuniform access of reactants to the outer catalyst surface and, as a consequence, undesired concentration and temperature profiles. Not surprisingly, this leads, in general, to lower yield and selectivity. In structured reactors, the catalyst is of a well-defined spatial structure, which can be designed in more detail. The hydrodynamics can be simplified to essentially laminar, well-behaved uniform fiow, enabling full access of reactants to the catalytic surface at a low pressure drop. 

The selection of reactor type in the traditionally continuous bulk chemicals industry has always been dominated by considering the number and type of phases present, the relative importance of transport processes (both heat and mass transfer) and reaction kinetics plus the reaction network relating to required and undesired reactions and any aspects of catalyst deactivation. The opportunity for economic... 

While alkane metathesis is noteworthy, it affords lower homologues and especially methane, which cannot be used easily as a building block for basic chemicals. The reverse reaction, however, which would incorporate methane, would be much more valuable. Nonetheless, the free energy of this reaction is positive, and it is 8.2 kj/mol at 150 °C, which corresponds to an equihbrium conversion of 13%. On the other hand, thermodynamic calculation predicts that the conversion can be increased to 98% for a methane/propane ratio of 1250. The temperature and the contact time are also important parameters (kinetic), and optimal experimental conditions for a reaction carried in a continuous flow tubiflar reactor are as follows 300 mg of [(= SiO)2Ta - H], 1250/1 methane/propane mixture. Flow =1.5 mL/min, P = 50 bars and T = 250 °C [105]. After 1000 min, the steady state is reached, and 1.88 moles of ethane are produced per mole of propane consmned, which corresponds to a selectivity of 96% selectivity in the cross-metathesis reaction (Fig. 4). The overall reaction provides a route to the direct transformation of methane into more valuable hydrocarbon materials. 

In order to exemplify the potential of micro-channel reactors for thermal control, consider the oxidation of citraconic anhydride, which, for a specific catalyst material, has a pseudo-homogeneous reaction rate of 1.62 s at a temperature of 300 °C, corresponding to a reaction time-scale of 0.61 s. In a micro channel of 300 pm diameter filled with a mixture composed of N2/02/anhydride (79.9 20 0.1), the characteristic time-scale for heat exchange is 1.4 lO" s. In spite of an adiabatic temperature rise of 60 K related to such a reaction, the temperature increases by less than 0.5 K in the micro channel. Examples such as this show that micro reactors allow one to define temperature conditions very precisely due to fast removal and, in the case of endothermic reactions, addition of heat. On the one hand, this results in an increase in process safety, as discussed above. On the other hand, it allows a better definition of reaction conditions than with macroscopic equipment, thus allowing for a higher selectivity in chemical processes. 

Selectivity may also come from reducing the contribution of a side reaction, e.g. the reaction of a labile moiety on a molecule which itself undergoes a reaction. Here, control over the temperature, i.e. the avoidance of hot spots, is the key to increasing selectivity. In this respect, the oxidative dehydrogenation of an undisclosed methanol derivative to the corresponding aldehyde was investigated in the framework of the development of a large-scale chemical production process. A selectivity of 96% at 55% conversion was found for the micro reactor (390 °C), which exceeds the performance of laboratory pan-like (40% 50% 550 °C) and short shell-and-tube (85% 50% 450 °C) reactors [73,110,112,153,154]. 

Selection of Corrosion-Resistant Materials The concentrated sofutions of acids, alkalies, or salts, salt melts, and the like used as electrolytes in reactors as a rule are highly corrosive, particularly so at elevated temperatures. Hence, the design materials, both metallic and nonmetallic, should have a sufficiently high corrosion and chemical resistance. Low-alloy steels are a universal structural material for reactors with alkaline solutions, whereas for reactors with acidic solutions, high-alloy steels and other expensive materials must be used. Polymers, including highly stable fluoropolymers such as PTFE, become more and more common as structural materials for reactors. Corrosion problems are of particular importance, of course, when materials for nonconsumable electrodes (and especially anodes) are selected, which must be sufficiently stable and at the same time catalytically active. 

It is clear from the presented data that the yield and selectivity in a large semibatch reactor can be improved compared to those in a small batch reactor that has much better heat-transfer capability. This has been achieved by decreasing the rate of heat evolution, which has been obtained by lowering the instantaneous concentration of reactant A. The results also indicate that the dosing policy can have a very significant influence on reactor performance. 

As illustrated by the examples above, the possibility of removing the generated heat from the reaction zone decreases with an increase in reactor size. As proven above, it can happen that the temperature of the reaction mixture in a full-scale reactor becomes higher than in the laboratory flask reactor. If multiple chemical reactions of distinctly different temperature sensitivities take place, differences in yields and selectivities between small and large reactors will be observed. This has a large influence on safety also. The laboratory reactor might still show satisfactory performance, while the industrial reactor might even explode. 

If the process is carried out in a stirred batch reactor (SBR) or in a plug-flow reactor (PFR) the final product will always be the mixture of both products, i.e. the selectivity will be less than one. Contrary to this, the selectivity in a continuous stirred-tank reactor (CSTR) can approach one. A selectivity equal to one, however, can only be achieved in an infinite time. In order to reach a high selectivity the mean residence time must be very long, and, consequently, the productivity of the reactor will be very low. A compromise must be made between selectivity and productivity. This is always a choice based upon economics. 

In reactor 1 2,6-xylenol is condensed with propylene oxide in the presence of NaOH at elevated temperature and pressure. The reaction is reasonably selective. However, some isomers are also formed in minor proportions. Therefore, the crude DMFP is dissolved in the organic solvent / and crystallized in tank 2, separated from the mother liquor in centrifuge 3, and dried in drier 4. 

---