Poly Rubber Oxidation

IR Isoprene rubber poly (els-1,4-isoprene) PEO Poly(ethylene oxide) a-Alkoxy- >-hydroxy polyethylene oxide... [Pg.762]

Polycarbonate is blended with a number of polymers including PET, PBT, acrylonitrile-butadiene-styrene terpolymer (ABS) rubber, and styrene-maleic anhydride (SMA) copolymer. The blends have lower costs compared to polycarbonate and, in addition, show some property improvement. PET and PBT impart better chemical resistance and processability, ABS imparts improved processability, and SMA imparts better retention of properties on aging at high temperature. Poly(phenylene oxide) blended with high-impact polystyrene (HIPS) (polybutadiene-gra/f-polystyrene) has improved toughness and processability. The impact strength of polyamides is improved by blending with an ethylene copolymer or ABS rubber. [Pg.143]

Cooper et al. [21, 22] reported in detail the results of their laborious work on the adsorption of four proteins human serum albumin (HSA), fibrinogen (FGN), fibronectin (FN), and vitronectin (VN), on five biomaterials polyethylene (PE), silicone rubber (SR), Teflon-FEP (FEP), poly(tetramethylene oxide)-poly-urethane (PTMO-PU), and polyethylene oxide)-polyurethane(PEO-PU). Hard segments of these polyurethanes are composed of a methylene-bis(p-phenylisocyanate) (MDI) chain extended wih 1,4-butanediol. [Pg.13]

MC MDI MEKP MF MMA MPEG MPF NBR NDI NR OPET OPP OSA PA PAEK PAI PAN PB PBAN PBI PBN PBS PBT PC PCD PCT PCTFE PE PEC PEG PEI PEK PEN PES PET PF PFA PI PIBI PMDI PMMA PMP PO PP PPA PPC PPO PPS PPSU Methyl cellulose Methylene diphenylene diisocyanate Methyl ethyl ketone peroxide Melamine formaldehyde Methyl methacrylate Polyethylene glycol monomethyl ether Melamine-phenol-formaldehyde Nitrile butyl rubber Naphthalene diisocyanate Natural rubber Oriented polyethylene terephthalate Oriented polypropylene Olefin-modified styrene-acrylonitrile Polyamide Poly(aryl ether-ketone) Poly(amide-imide) Polyacrylonitrile Polybutylene Poly(butadiene-acrylonitrile) Polybenzimidazole Polybutylene naphthalate Poly(butadiene-styrene) Poly(butylene terephthalate) Polycarbonate Polycarbodiimide Poly(cyclohexylene-dimethylene terephthalate) Polychlorotrifluoroethylene Polyethylene Chlorinated polyethylene Poly(ethylene glycol) Poly(ether-imide) Poly(ether-ketone) Polyethylene naphthalate Polyether sulfone Polyethylene terephthalate Phenol-formaldehyde copolymer Perfluoroalkoxy resin Polyimide Poly(isobutylene), Butyl rubber Polymeric methylene diphenylene diisocyanate Poly(methyl methacrylate) Poly(methylpentene) Polyolefins Polypropylene Polyphthalamide Chlorinated polypropylene Poly(phenylene oxide) Poly(phenylene sulfide) Poly(phenylene sulfone)... [Pg.959]

PB PBI PBMA PBO PBT(H) PBTP PC PCHMA PCTFE PDAP PDMS PE PEHD PELD PEMD PEC PEEK PEG PEI PEK PEN PEO PES PET PF PI PIB PMA PMMA PMI PMP POB POM PP PPE PPP PPPE PPQ PPS PPSU PS PSU PTFE PTMT PU PUR Poly(n.butylene) Poly(benzimidazole) Poly(n.butyl methacrylate) Poly(benzoxazole) Poly(benzthiazole) Poly(butylene glycol terephthalate) Polycarbonate Poly(cyclohexyl methacrylate) Poly(chloro-trifluoro ethylene) Poly(diallyl phthalate) Poly(dimethyl siloxane) Polyethylene High density polyethylene Low density polyethylene Medium density polyethylene Chlorinated polyethylene Poly-ether-ether ketone poly(ethylene glycol) Poly-ether-imide Poly-ether ketone Poly(ethylene-2,6-naphthalene dicarboxylate) Poly(ethylene oxide) Poly-ether sulfone Poly(ethylene terephthalate) Phenol formaldehyde resin Polyimide Polyisobutylene Poly(methyl acrylate) Poly(methyl methacrylate) Poly(methacryl imide) Poly(methylpentene) Poly(hydroxy-benzoate) Polyoxymethylene = polyacetal = polyformaldehyde Polypropylene Poly (2,6-dimethyl-l,4-phenylene ether) = Poly(phenylene oxide) Polyp araphenylene Poly(2,6-diphenyl-l,4-phenylene ether) Poly(phenyl quinoxaline) Polyphenylene sulfide, polysulfide Polyphenylene sulfone Polystyrene Polysulfone Poly(tetrafluoroethylene) Poly(tetramethylene terephthalate) Polyurethane Polyurethane rubber... [Pg.939]

Blends of poly(3-hydroxyalkanoic acid)s (PHAs) with various natural and synthetic polymers have been reported as reviewed in Refs. [21,22]. By blending with synthetic polymers it is expected to control the biodegradability, to improve several properties, and to reduce the production cost of bacterially synthesized PHAs. The polymers investigated as the blending partners of PHAs include poly(ethylene oxide) [92, 93], poly(vinyl acetate) [94], poly(vinylidene fluoride) [95], ethylene propylene rubber [94, 96], po-ly(epichlorohydrin) [97, 98], poly(e-caprolactone) [99], aliphatic copolyesters of adipic acid/ethylene glycole/lactic acid [100] and of e-caprolactone/lactide... [Pg.805]

Polyblends with Soft Matrix. Polyblends in which both phases are soft are mixtures of different rubbers. Treads of automobile tires are made of polyblends of SBR with either natural rubber or cts-polybutadiene. Co vulcanization of EPDM with various rubbers is discussed in the chapter of M. E. Woods and T. R. Mass. Relaxation behavior of blends of EVA rubber with styrene/ethylene-butylene/styrene block copolymer and of poly (ethylene oxide) with ethylene oxide/propylene oxide/ethylene oxide block copolymer were studied by M. Shen, U. Mehra, L. Toy, and K. Biliyar. [Pg.13]

As was already stated (see Figure 6), the temperature dependence of the shift factor aT is a function of the elastomer phase content. The strong effect of the rubber content on the temperature dependence of the shift factor aT could be explained by an increase in free volume of the SAN resin induced by the elastomer phase, as was suggested by Prest and Porter (13) for polystyrene-poly (phenylene oxide) blends. In order to verify this hypothesis, log aT experimental data for SAN and relative blends were used to calculate the WLF parameters and, in turn, the free volumes (f0) at the reference temperature (T0) and the thermal expansion coefficients (a) by the equation ... [Pg.195]

Polymers Characterized by HT-GPC A number of polymers can be characterized by GPC in 1,2,4-trichlorobenzene at an elevated temperature polyethylene, polypropylene, poly(ethylene-vinyl acetate), poly(ethylene-methyl acrylate), polyethylene propylene diamine rubber, different types of butyl rubber, and poly(phenylene oxide). In Table 17.3 are presented some common polymers, as well... [Pg.360]

The ability of living polymers to resume growth with the addition of fresh monomer provides an excellent opportunity for the preparation of block copolymers. For example, if a living polymer with one active end from monomer A can initiate the polymerization of monomer B, then an A-AB-B type copolymer can be obtained (e.g., styrene-isoprene copolymer). If, however, both ends of polymer A are active, a copolymer of the type B-BA-AB-B results. Examples are the thermoplastic rubbers polysty-rene-polyisoprene-polystyrene and poly(ethylene oxide)-polystyrene-poly(ethylene oxide). In principle, for fixed amounts of two monomers that are capable of mutual formation of living polymers, a series of polymers with constant composition and molecular weight but of desired structural pattern can be produced by varying the fraction and order of addition of each monomer. [Pg.213]

The ability of poly(ethylene oxide) to reduce hydrodynamic drag has also led to its use in fluid-jet systems used for cutting soft goods, such as textiles, rubber, foam, cardboard, etc. In these systems specially designed nozzles produce a very-small-diameter water jet at a pressure of 30,000-60,000 psi (200-400 MPa). Although a plain water disperses significantly as it leaves the nozzle, with poly(ethylene oxide) addition the stream becomes more cohesive and maintains its very small diameter up to 4 in. (10 cm) firom the nozzle. [Pg.492]

Polyoxymethylene, polyformaldehyde Propylene oxide rubber Polypropylene Poly(phenylene ether) Poly(para-methylstyrene) Poly(phenylene oxide)... [Pg.126]

Typical polyurethanes use a diol extender such as 1,4 butane diol. The NH groups form hydrogen bonds with C=0 groups on neighbouring chains, inside very small, hard blocks. The soft blocks are crosslinked polyethers or polyesters. A typical polyether is poly(propylene oxide) —[—O—CH2— C(CH2)H—] pre-polymerised to a molecular mass Mn of about 6000, a degree of polymerisation n = 140. The PPO has a glass transition temperature of about —60 °C, so the crosslinked PPO is a rubber. This rubbery phase is connected, via the polyurethane molecules, to the crystalline phase. [Pg.115]

FrOlich et al. [ 140] investigated a system in which DGEBA was mixed with hydroxy-terminated poly(propylene oxide-block-ethylene oxide) as the rubber, with the nanoclay being a synthetic fluorohectorite treated with bis (2-hydroxyethyl) methyl tallow alkylammonium ions. The clay was first blended with rubber, before being dispersed into the reactive epoxy mixture. Modification of the rubber allowed variation in miscibility and differing morphologies and properties. If the rubber was miscible, the intercalated clay led to improved toughness. If the rubber is sufficiently modified, such as with... [Pg.73]

OPR Oxypropylene rubber [poly(propylene oxide) rubber]... [Pg.807]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...