Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Performance and support

Harness JR, Automation of high-throughput synthesis, Automated laboratory workstations designed to perform and support combinatorial chemistry, In Chaiken IM, Janda KD, eds., Molecular Diversity and Combinatorial Chemistry Libraries and Drug Discovery, ACS Conference Proceedings Series, Washington, DC, American Chemical Society, pp. 188-198, 1996. [Pg.342]

Analysis (TGA) of the HF/SbFj dissolution products has been performed and supports the AnF4-2SbF5 + 2(H30" ) (SbFg) formulation for both U and Th systems. A typical TGA run is shown in fig. 8. Equations (7)-(ll) indicate the possible - through by no means certain - processes occurring during the stepwise thermal decomposition of the uranium salt,... [Pg.520]

In order to demonstrate the importance of all methods described in previous section, the RAM analysis performed to assess the Boiler system in decommissioning phase will be carried out. The main objective is to define the critical equipment in terms of performance and support decision about which one must to be taken place for a new one. [Pg.231]

The Cymru supplier association was therefore formed from a wide variety of companies, in terms of both size and industry sector. In a marked break with the past, Cymru kicked off the association with an inaugural meeting that presented confidential product development and market information. The aim of the association was to promote best practice, improve overall supply chain performance and support product development. This was to be achieved by self-help teams committed to sharing knowledge and experience in an open and cooperative manner. Many suppliers were concerned that the association was being formed as a disguise for margin reduction, and were reassured when Cymru insisted that the main task was cost reduction. More open communications and an emphasis on mutual cost reduction were seen by suppliers as essential foundations for the new association. [Pg.279]

An ongoing evaluation is essential to ensure that the expectation in the framework are being meet. OE employs internal and external assessment processes to gage the degree to which expectations are being achieved. Such evaluations provide evaluations to determine areas for further improvements both in performance and supportive management... [Pg.184]

Chemical processes will in the future need to be designed as part of a sustainable industrial development which retains the capacity of ecosystems to support industrial activity and life. This book therefore places a high emphasis on waste minimization and energy efficiency in the context of good economic performance and good health and safety practices. [Pg.473]

There are at least four different classification systems for cemented carbides (7,12). The U.S. system is based on relative performance the U.K. system is based on properties, and the former USSR system on composition the fourth system, widely used in Europe and supported by the ISO, is based on apphcation and chip form. In this article, the U.S. system and the ISO system are briefly reviewed. [Pg.204]

Mobile ions, such as sodium or potassium, tend to migrate to thep-n junction of the IC device where they acquire an electron, and deposit as the corresponding metal on the p-n junction this consequendy destroys the device. Furthermore, mobile ions also support leakage currents between biased device features, which degrade device performance and ultimately destroy the devices by electrochemical processes such as metal conductor dissolution. [Pg.188]

Quantitative risk analysis (QRA) is a powerful analysis approach used to help manage risk and improve safety in many industries. When properly performed with appropriate respect for its theoretical and practical limitations, QRA provides a rational basis for evaluating process safety and comparing improvement alternatives. However, QRA is not a panacea that can solve all problems, make decisions for a manager, or substitute for existing safety assurance and loss prevention activities. Even when QRA is preferred, qualitative results, which always form the foundation for QRA, should be used to verify and support any conclusions drawn from QRA. [Pg.79]

This work was performed at Sandia National Laboratories and supported by the U.S. Department of Energy under Contract DE-AC04-76DP00789. [Pg.323]

The most straightforward way of proof testing the equipment would be to reproduce site conditions completely. Under such conditions, the testing would easily establish if the compressor performance requirements are met and if the driver and support systems function as intended and are adequate for the purpose. [Pg.407]

A risk assessment analyses systems at two levels. The first level defines the functions the system must perform to respond successfully to an accident. The second level identifies the hardware for the systems use. The hardware identification (in the top event statement) describes minimum system operability and system boundaries (interfaces). Experience shows that the interfaces between a frontline system and its support systems are important to the system cs aluaiion and require a formal search to document the interactions. Such is facilitated by a failure modes and effect analysis (FMEA). Table S.4.4-2 is an example of an interaction FMEA for the interlace and support requirements for system operation. [Pg.106]

As part of developing the PSM implementation plan (Chapter 5), you and the team identified benefits unique to the approach you selected, using them to help win management s approval. For example, your plan may focus on priority elements because the assessment you conducted suggests that this method will yield the greatest overall improvement in safety performance. And, as part of the pilot test described in this chapter, you focused on facility-specific benefits to enlist the support of local management and staff. [Pg.162]

The integration program was most likely supported by senior management because they saw opportunities to improve performance that is, better end-of-pipe performance and more efficient management. In most cases, improvements in end-of-pipe performance will take a considerable time to become evident. Measuring efficiency improvements and leading indicators of improved end-of-pipe performance must start as early as possible. [Pg.122]

This chapter illustrates the improvements in SEC column technology and modern applications of SEC separations. The better understanding of SEC column design and separation parameters described in the theoretical sections of this chapter will help the reader fine-tune his or her own work. The same is true for column performance tests, which should be applied regularly, especially after a column purchase. In order to obtain reproducible results, it is recommended to choose column manufacturers who can assure constant quality and performance and to invest in knowledgeable, well-trained support personnel and experienced application chemists. [Pg.298]


See other pages where Performance and support is mentioned: [Pg.100]    [Pg.128]    [Pg.28]    [Pg.332]    [Pg.168]    [Pg.130]    [Pg.327]    [Pg.226]    [Pg.458]    [Pg.621]    [Pg.100]    [Pg.128]    [Pg.28]    [Pg.332]    [Pg.168]    [Pg.130]    [Pg.327]    [Pg.226]    [Pg.458]    [Pg.621]    [Pg.102]    [Pg.55]    [Pg.139]    [Pg.140]    [Pg.245]    [Pg.336]    [Pg.10]    [Pg.519]    [Pg.67]    [Pg.399]    [Pg.436]    [Pg.223]    [Pg.379]    [Pg.169]    [Pg.775]    [Pg.1738]    [Pg.64]    [Pg.239]    [Pg.3]    [Pg.13]    [Pg.362]    [Pg.159]   
See also in sourсe #XX -- [ Pg.499 , Pg.503 , Pg.507 , Pg.510 , Pg.512 , Pg.515 , Pg.527 , Pg.531 , Pg.536 ]




SEARCH



© 2024 chempedia.info