Passivity passive film

Corrosion protection of metals can take many fonns, one of which is passivation. As mentioned above, passivation is the fonnation of a thin protective film (most commonly oxide or hydrated oxide) on a metallic surface. Certain metals that are prone to passivation will fonn a thin oxide film that displaces the electrode potential of the metal by +0.5-2.0 V. The film severely hinders the difflision rate of metal ions from the electrode to tire solid-gas or solid-liquid interface, thus providing corrosion resistance. This decreased corrosion rate is best illustrated by anodic polarization curves, which are constructed by measuring the net current from an electrode into solution (the corrosion current) under an applied voltage. For passivable metals, the current will increase steadily with increasing voltage in the so-called active region until the passivating film fonns, at which point the current will rapidly decrease. This behaviour is characteristic of metals that are susceptible to passivation. 

Stimming U 1986 Photoeleotroohemioal studies of passive films Eleotroohim. Aota 31 415... 

In tenns of an electrochemical treatment, passivation of a surface represents a significant deviation from ideal electrode behaviour. As mentioned above, for a metal immersed in an electrolyte, the conditions can be such as predicted by the Pourbaix diagram that fonnation of a second-phase film—usually an insoluble surface oxide film—is favoured compared with dissolution (solvation) of the oxidized anion. Depending on the quality of the oxide film, the fonnation of a surface layer can retard further dissolution and virtually stop it after some time. Such surface layers are called passive films. This type of film provides the comparably high chemical stability of many important constmction materials such as aluminium or stainless steels. 

Highly protective layers can also fonn in gaseous environments at ambient temperatures by a redox reaction similar to that in an aqueous electrolyte, i.e. by oxygen reduction combined with metal oxidation. The thickness of spontaneously fonned oxide films is typically in the range of 1-3 nm, i.e., of similar thickness to electrochemical passive films. Substantially thicker anodic films can be fonned on so-called valve metals (Ti, Ta, Zr,. ..), which allow the application of anodizing potentials (high electric fields) without dielectric breakdown. 

The protective quality of the passive film is detennined by the ion transfer tlirough the film as well as the stability of the film with respect to dissolution. The dissolution of passive oxide films can occur either chemically or electrochemically. The latter case takes place if an oxidized or reduced component of the passive film is more soluble in the electrolyte than the original component. An example of this is the oxidative dissolution of CrjO ... 

From polarization curves the protectiveness of a passive film in a certain environment can be estimated from the passive current density in figure C2.8.4 which reflects the layer s resistance to ion transport tlirough the film, and chemical dissolution of the film. It is clear that a variety of factors can influence ion transport tlirough the film, such as the film s chemical composition, stmcture, number of grain boundaries and the extent of flaws and pores. The protectiveness and stability of passive films has, for instance, been based on percolation arguments [67, 681, stmctural arguments [69], ion/defect mobility [56, 57] and charge distribution [70, 71]. 

To illustrate some of the different approaches, let us consider passive films grown on Fe-Cr alloys. It has been established since 1911 [72] that an increase of Cr in the alloy increases the stability of the oxide film against dissolution. 

This example illustrates that exact infonnation on the chemistry and stmcture of the passive film is necessary to clarify the mechanisms relevant to stability and protectiveness of passive films. 

As outlined above, electron transfer through the passive film can also be cmcial for passivation and thus for the corrosion behaviour of a metal. Therefore, interest has grown in studies of the electronic properties of passive films. Many passive films are of a semiconductive nature [92, 93, 94, 95, 96, 97, 98, 99, 100, 101, 102 and 1031 and therefore can be investigated with teclmiques borrowed from semiconductor electrochemistry—most typically photoelectrochemistry and capacitance measurements of the Mott-Schottky type [104]. Generally it is found that many passive films cannot be described as ideal but rather as amorjDhous or highly defective semiconductors which often exlribit doping levels close to degeneracy [105]. 

Films, anodic oxide Films, passivating Films, plastic Film theory Film wrappers Filter Filter aid Filter aids Filter fabrics Filtering centrifuges Filter media Filters... 

The following mechanisms in corrosion behavior have been affected by implantation and have been reviewed (119) (/) expansion of the passive range of potential, (2) enhancement of resistance to localized breakdown of passive film, (J) formation of amorphous surface alloy to eliminate grain boundaries and stabilize an amorphous passive film, (4) shift open circuit (corrosion) potential into passive range of potential, (5) reduce/eliminate attack at second-phase particles, and (6) inhibit cathodic kinetics. 

The occurrence of pitting seems to stem from the differential stabiUty of the passive film that forms on the titanium alloy. This film does not break down uniformly even when the electrolytes are fluoride and bromide based. The pitting can be so severe that special measures are needed to counteract it. 

In most cases, CVD reactions are activated thermally, but in some cases, notably in exothermic chemical transport reactions, the substrate temperature is held below that of the feed material to obtain deposition. Other means of activation are available (7), eg, deposition at lower substrate temperatures is obtained by electric-discharge plasma activation. In some cases, unique materials are produced by plasma-assisted CVD (PACVD), such as amorphous siHcon from silane where 10—35 mol % hydrogen remains bonded in the soHd deposit. Except for the problem of large amounts of energy consumption in its formation, this material is of interest for thin-film solar cells. Passivating films of Si02 or Si02 Si N deposited by PACVD are of interest in the semiconductor industry (see Semiconductors). 

The heat-transfer quaUties of titanium are characterized by the coefficient of thermal conductivity. Even though the coefficient is low, heat transfer in service approaches that of admiralty brass (thermal conductivity seven times greater) because titanium s greater strength permits thinner-walled equipment, relative absence of corrosion scale, erosion—corrosion resistance that allows higher operating velocities, and the inherently passive film. 

Precipitating (cathodic) inhibitors are simply chemicals that form insoluble precipitates that can coat and protect the surface precipitated films are not as tenacious as passive films and take longer to repair after a system upset. 

Liquid Cathode Cells. Liquid cathode cells were discovered at almost the same time as the successful soHd cathode cells. A strongly oxidising hquid such as SO2, was deterrnined to be suitable for direct contact with the strongly reducing lithium, because an excellent passivating film forms... 

Chlorides, which are ubiquitous in nature, play an important role in the corrosion of metals. Chlorides and other anions also play an important role in locali2ed corrosion, ie, the breakdown of the insoluble protective reaction product films, eg, passive films, that prevent corrosion of the underlying metal. A variety of mechanisms attempting to explain the role of chloride in general and in locali2ed corrosion have been proposed (23—25). 

The stainless steels contain appreciable amounts of Cr, Ni, or both. The straight chrome steels, types 410, 416, and 430, contain about 12, 13, and 16 wt % Cr respectively. The chrome—nickel steels include type 301 (18 wt % Cr and 9 wt % Ni), type 304 (19 wt % Cr and 10 wt % Ni), and type 316 (19 wt % Cr and 12 wt % Ni). Additionally, type 316 contains 2—3 wt % Mo which gready improves resistance to crevice corrosion in seawater as well as general corrosion resistance. AH of the stainless steels offer exceptional improvement in atmospheric conditions. The corrosion resistance results from the formation of a passive film and, for this reason, these materials are susceptible to pitting corrosion and to crevice corrosion. For example, type 304 stainless has very good resistance to moving seawater but does pit in stagnant seawater. 

Films Once corrosion has started, its further progress very often is controlled by the nature of films, such as passive films, that may form or accumulate on the metallic surface. The classical example is the thin oxide tilm that forms on stainless steels. 

Short-time tests also can give misleading results on alloys that form passive films, such as stainless steels. With Borderline conditions, a prolonged test may be needed to permit breakdown of the passive film and subsequently more rapid attack. Consequently, tests run for long periods are considerably more reahstic than those conducted for short durations. This statement must be quahfied by stating that corrosion should not proceed to the point at which the original specimen size or the exposed area is drastic y reduced or the metal is perforated. 

Use and Uimitations of Electrochemical Techniques A major caution must be noted as to the general, indiscriminate use of all electrochemical tests, especially the use of AC and EIS test techniques, for the study of corrosion systems. AC and EIS techniques are apphcable for the evaluation of very thin films or deposits that are uniform, constant, and stable—for example, thin-film protective coatings. Sometimes, researchers do not recognize the dynamic nature of some passive films, corrosion produc ts, or deposits from other sources nor do they even consider the possibility of a change in the surface conditions during the course of their experiment. As an example, it is note-... 

Sihcon irons are very resistant to oxidizing and reducing environments, and resistance depends on the formation of a passive film. These irons are widely used in siilfuric acid service, since they are unaffec ted by siilfuric at all strengths, even up to the boihng point. 

Generally, pitting corrosion only occurs on passivated metals when the passive film is destroyed locally. In most cases chloride ions cause this local attack at potentials U > U q. Bromide ions also act in the same way [51], The critical potential for pitting corrosion UpQ is called the pitting potential. It has the same significance as in Eqs. (2-39) and (2-48). 

Fatigue life can be slightly lengthened by anodic protection or by passivation. In acids even passive stainless CrNi steels suffer corrosion fatigue [104]. Resistance can occur if the passive film itself has a fatigue strength (e.g., in neutral waters [105]). 

---