Monitoring the

Comparing the overall concentrations of these different carbons designated generally as structural patterns , measured before and after a process such as FCC or hydrocracking (see Chapter 10), enables the conversion to be monitored the simple knowledge of the percentage of condensed aromatic carbon of a feedstock gives an indication of its tendency to form coke. 

There always is a relation between fuel composition and that of hydrocarbon emissions to the atmosphere, whether it concerns hydrocarbon emissions from evaporative losses from the fuel system, or from exhaust gases. This is the reason that environmental protection regulations include monitoring the composition of motor and heating fuels. We will describe here the regulations already in existence and the work currently underway in this area with its possible effects on refining. 

As subsea production systems are remote from the host production facility there must be some type of system in place which allows personnel on the host facility to control and monitor the operation of the unmanned subsea system. 

Sensors on the tree allow the control module to transmit data such as tubing head pressure, tubing head temperature, annulus pressure and production choke setting. Data from the downhole gauge is also received by the control module. With current subsea systems more and more data is being recorded and transmitted to the host facility. This allows operations staff to continuously monitor the performance of the subsea system. 

A more sophisticated and increasingly popular method of on-condItion maintenance is to monitor the performance of equipment on-line. For example, a piece of rotating equipment such as a turbine may be monitored for vibration and mechanical performance (speed, inlet and outlet pressure, throughput). If a base-line performance is established, then deviations from this may indicate that the turbine has a mechanical problem which will reduce its performance or lead to failure. This would be used to alert the operators that some form of repair is required. 

A programme of monitoring the reservoir is carried out, in which me asurements are made and data are gathered. Figure 14.2 indicates some of the tools used to gather data, the information which they yield, and the way In which the information is fed back to update the models and then used to refine the ongoing reservoir development strategy. 

Some specific examples of the use of data gathered while monitoring the reservoir will now be discussed. 

Monitoring the resenro/rpressure will also indicate whether the desired reservoir depletion policy is being achieved. For example, if the development plan was intended to maintain reservoir pressure at a chosen level by water injection, measurements of the pressure in key wells would show whether all areas are receiving the required pressure support. 

Due to the fact, that AE by its peculiarities can be used to prevent catastrophic failure of structures and control the application of load, the higher risk of a pneumatic pressure test can be reduced significantly by the monitoring the structure during the loading by AE. 

The first 3 items of the above list (waveguides, transducers and preamplifiers) are located at or near to the component(s) to be monitored. The other items must be installed in the control room area, mounted into a single instrumentation rack (fig. 4). 

The accuracy of the presented methods was verified using test pipes with various diameters and wall thickness of which the wall thickness was measured independently using a slide-rule. Both on film and on the monitor the wall thickness could be determined within an accuracy of ca. 0.2 - 0.3 mm. 

The investigations show that the microfocus high speed radioscopy system is suitable for monitoring the hard particle transport during laser beam dispersing. It is possible to observe and analyse the processes inside the molten bath with the presented test equipment. As a consequence a basis for correlation with the results of a simulation is available. 

The fish block will be moved through the X-ray beam and the resulting image is studied on the high resolution monitor. The operator has the ability to judge a block as acceptable, rejectable or downgrade able via push-button. 

Shearography monitors the speckular 2D interference pattern of an unpolished surface illuminated by a coherent light source, and is therefore a metliod that lends itself to the testing of industrial materials. Small surface, or near-surface defects may produce localised strain on... 

In order that the data acquisition system can obtain information about the spatial location and orientation of the probe, a four-channel incremental encoder interface board is installed. Three channels are used to define position in three-dimensional space, while the fourth monitors the skew of the probe (skew is defined as rotation about an axis normal to the probe face). Although six measurements are required to completely define the location and orientation, it is assumed that the probe remains in contact with the inspection surface. 

The status bar displays information about the current status of the acquisition system the position of each of the four axes of the probe position monitor the maximum amplitude of the signal within the gate for both the coupling channel and the signal (flaw detection) channel and the current operating mode of the system, which may be record-... 

Ultrasonic reflections out of the weld volume are documented in a top and side view together with the area of weld volume scanned. A new coupling monitoring system ensures 100% coupling reliability. Furthermore the systems does not require any mechanics to monitor the probe position as the position data is monitored by airborne sound sensors. 

The scan mode display is divided into a number of windows, that display the data recorded from the active inspections. In addition, the A-scan data from the ultrasonic probes can be displayed in probe monitor windows, for monitoring the signal quality. Figure 7 shows the scan mode display for simultaneous recording of two P-scan inspections (displayed in the same presentation window) and a T-scan inspection together with 3 probe monitor windows. 

Insufficient information about the properties, layout pattern of small defects, potential for their growth in time, usually leads either to an unjustified rejection (repair) or to underestimation of the importance of the defect and, as aconsequence, construction failure. Use of automated computerised means of control allows safe service of the old constructions, periodically repeating the UT and monitoring the development of discontinuities in the metal. The main idea of such policy is periodical UT of development of discontinuities or, in a more general form, monitoring of the metal condition. 

The encircling probe was characterised with its mirror in water. As we did not own very tiny hydrophone, we used a reflector with hemispherical tip with a radius of curvature of 2 mm (see figure 3c). As a result, it was possible to monitor the beam at the tube entrance and to measure the position of the beam at the desired angle relatively to the angular 0° position. A few acoustic apertures were verified. They were selected on an homogeneous criteria a good one with less than 2 dB of relative sensitivity variations, medium one would be 4 dB and a bad one with more than 6 dB. 

The porosity content in composite material is known to influence the strength of the material. It is therefore of interest to monitor the porosity contents Anting manufacturing. 

For the purpose of enviromnent monitoring the infrared (IR) detectors are widely used, they allow to determine the concentration of contaminants, aerosols and etc. at the distance up to 10 km. 

The user inspectorate must fulfil the same technical criteria as the notified body. In addition, it must be organisationally identifiable and demonstrate its impartiality. It must not engage in any activities that might conflict with its independence of judgement and integrity. Given that the authorisation of user inspectorates to carry out conformity assessment is an innovation for technical harmonisation at Union level, the Commission shall monitor the application of this measure and evaluate its effects three years after the coming into force of the directive. 

Sample scan data is a good way to archive the results of an inspection. The inspection could be re-visited later to see how the eddy-current response has changed over time. Random audits of the quality of inspection detection could be monitored. The inspection could also be reviewed if new information becomes known, say from inspection conducted using alternate methods. 

Gas flaring in offshore installations and oil refineries represents a source of loss of energy making it important to operators and authorities to monitor the amounts of flared gas. In some countries the flare gas is subject to CO2 tax. Flow metering systems are installed on some but not all flare systems. 

---