Probes ultrasonic

Parameters of ultrasonic probe wideband angle beam probe with the frequency of 1.1-3.9MHz. 

Special Inspection Problems Solved by Means of Matched Ultrasonic Probe Design. 

The scan mode display is divided into a number of windows, that display the data recorded from the active inspections. In addition, the A-scan data from the ultrasonic probes can be displayed in probe monitor windows, for monitoring the signal quality. Figure 7 shows the scan mode display for simultaneous recording of two P-scan inspections (displayed in the same presentation window) and a T-scan inspection together with 3 probe monitor windows. 

Airborne Ultrasonic Probes Design, Fabrication, Application. 

Based upon a piezoelectric 1-3-composite material, air-bome ultrasonic probes for frequencies up to 2 MHz were developped. These probes are characterized by a bandwidth larger than 50 % as well as a signal-to-noise ratio higher than 100 dB. Applications are the thickness measurement of thin powder layers, the inspection of sandwich structures, the detection of surface near cracks in metals or ceramics by generation/reception of Rayleigh waves and the inspection of plates by Lamb waves. 

In wide sectors of industry there is a growing need of inspection methods which go without liquid coupling media. The excitation of bulk and surface waves by means of air-coupled ultrasonic probes is therefore an attractive tool for NDE. This is tme e.g. for the rapid scanning of large composite structures in the aerospace industry [1]. In other cases, the use of liquid couplants is prohibitive like the thickness measurement of powder layers. 

The air-coupled ultrasonic probes are essentially built up by the piezo-composite plate and a front side matching layer, made of air bubbles filled plastic materials. By using a thermoplastic material as matrix material of the composite, the transducer can easily be shaped by heating up, forming and cooling down to realize focusing transducers. Because of the low... 

Intelligent vehicles have been developed with arrays of ultrasonic probes for pipeline inspection — one commercial version contains 512 ultrasonic sensors. 

On a laboratory scale, generally an ultrasonic probe (horn) and an ultrasonic cleaner are used. The ultrasonic field in an ultrasonic cleaner is not homogeneous. Sonication extraction uses ultrasonic frequencies to disrupt or detach the target analyte from the matrix. Horn type sonic probes operate at pulsed powers of 400-600 W in the sample solvent container. Ultrasonic extraction works by agitating the solution and producing cavitation in the... 

In the preceding chapters many aspects of sonochemistry and its application have already been discussed in details and now to conclude, few experiments are being discussed here to make the beginners in the field of sonochemistry, especially the undergraduate students, to ride on the sound wave and begin their journey of sonochemistry with some of these experiments, which can be conveniently carried out with an ultrasonic cleaning bath (Fig. 15.1) or an ultrasonic probe (Fig. 15.2) of 20 kHz, available commercially abundantly. 

Methodology The ultrasonic probe is used for the experiment which allows relatively more acoustic energy directly into the system. Indicators were sonicated for different durations and the absorbance was recorded using UV-vis spectrophotometer. The values, however, given in the table below give qualitative idea of the degradation of indicators. 

The connection between the use of ultrasound for the machining and drilling of hard materials (see below) and dentistry is clear since tooth enamel is a very hard material. In the dentist s surgery a new instrument has been introduced which is essentially a small ultrasonic probe operating at 25 kHz with a variety of attachments. Although... 

In many syntheses activation is not effected by sonochemical preparation of the metal alone but rather by sonication of a mixture of the metal and an organic reagent(s). The first example was published many years ago by Renaud, who reported the beneficial role of sonication in the preparation of organo-lithium, magnesium, and mercury compounds [86]. For many years, these important findings were not followed up but nowadays this approach is very common in sonochemistry. In another early example an ultrasonic probe (25 kHz) was used to accelerate the preparation of radical anions [87]. Unusually for this synthesis of benzoquinoline sodium species (5) the metal was used in the form of a cube attached to the horn and preparation times in diethyl ether were reduced from 48 h (reflux using sodium wire) to 45 min using ultrasound. 

A similar combination of ultrasound and photocatalysis has also been reported to destroy 2,4,6-trichlorophenol in aqueous solution [39]. An ultrasonic probe (22 kHz) with a uv light source (15 W) was used to examine the effect of changing such operating conditions as ultrasonic intensity, reaction temperature and uv transmission. The experiments involved using 2,4,6-trichlorophenol (100 ppm) and TiOj (0.1 g L ) and showed that the degradation rates increased with the temperature of the solution. The cumulative effect was more pronounced at lower ultrasonic intensities with little additional benefit derived at increased ultrasonic powers. 

In sediment and soil samples, the isomers of cresol are determined by transferring a small portion of the solid sample (1 g) to a vial and adding methylene chloride. The contaminants are extracted from the sample with the aid of an ultrasonic probe. The methylene chloride extract is filtered, concentrated, and subjected to GC/MS analysis for quantitation. 

Deionized water (720 g), sodium lauryl sulfate (4.3 g), dioctanoyl peroxide (40 g), and acetone (133 g) were emulsified using an ultrasonic probe for 10 minutes. The step 1 polystyrene seed (48.0 g seed, 578 g latex) was added to the emulsion together with lauryl sulfate (0.8 g) and acetone (29.6 g). The mixture was transferred to a flask and left to agitate at approximately 25°C for 48 hours. Acetone was then removed and the solution added to a 5-liter double-walled glass reactor. The temperature was increased to 40°C while styrene (336 g) and divinyl benzene (0.88 g) were added drop-wise over approximately 60 minutes. After 4 hours the mixture was treated with deionized water (1200 g), potassium iodide (1.28 g), and polyvinyl pyrrolidone (18.48 g) with the temperature increased to 70°C. The polymerization continued for 6 hours at 70°C and 1 hour at 90°C. Styrene-based oligomer particles with a diameter of 1.7 pm and with a narrow size distribution were obtained. 

By coupling an ultrasonic probe with a microwave reactor and propagating the ultrasound waves into the reactor via decalin introduced into their double jacket design, Chemat et al. studied the esterification of acetic acid with propanol and the pyrolysis of urea to afford a mixture of cyanuric acid, ameline and amelide (Scheme 9.19)136. Improved results were claimed compared to those obtained under conventional and microwave heating. The MW-US technique was also used to study the esterification of stearic acid with butanol and for sample preparation in chemical analysis137,138. 

---