Linear butadiene-styrene

LDPE = low density polyethylene LLDPE = linear low density polyethylene HDPE = high density polyethylene PP = polypropylene PVC = polyvinyl chloride PS = polystyrene ABS = polyacrylonitrile-butadiene-styrene. 

More recently Fina Chemicals have introduced linear SBS materials (Finaclear) in which the butadiene is present both in block form and in a mixed butadiene-styrene block. Thus comparing typical materials with a total styrene content of about 75% by weight, the amount of rubbery segment in the total molecule is somewhat higher. As a result it is claimed that when blended with polystyrene the linear block copolymers give polymers with a higher impact strength but without loss of clarity. 

Linear triblock copolymers of the type styrene-butadiene-styrene (SBS) and styrene-isoprene-styrene (SIS) are produced commercially by anionic polymerization through sequential addition of monomers in the reaction chamber [10] as shown below ... 

Improvement in the processing and vulcanized qualities of a range of systems have been reported over the past decades. Modification of natural rubber, due to work in the British Rubber Producers Research Association, yields some of the most striking applications of microgel. A detailed study at the MV Lomonosov Institute of Fine Chemical Technology, in Moscow, on the effect of microgels on mechanical properties of cis-polyisoprene and butadiene-styrene rubbers extensively illustrates the properties of blends from latex combination of microgel and conventional or linear systems.(31)... 

Asaparene Linear block styrene copolymer with butadiene Asahi... 

Stearon Linear block styrene-butadiene copolymers Firestone... 

Upon irradiation, 1,4 polybutadienes and poly(butadiene-styrene) form free radicals relatively readily, and their concentration has been found to increase linearly proportional to dose up to approximately 100 Mrad (1,000 kGy). ... 

Order-disorder transitions and spinodals were computed for linear multi block copolymers with differing sequence distributions by Fredrickson et al. (1992). This type of copolymer includes polyurethanes, styrene-butadiene rubber, high impact polystyrene (HIPS) and acrylonitrile-butadiene-styrene (ABS) block copolymers. Thus the theory is applicable to a broad range of industrial thermoplastic elastomers and polyurethanes. The parameter... 

Here n is the average refractive index, k is Boltzman s constant, and T is absolute temperature (13). If a polyblend were to form a homogeneous network, the stress would be distributed equally between network chains of different composition. Assuming that the size of the statistical segments of the component polymers remains unaffected by the mixing process, the stress-optical coefficient would simply be additive by composition. Since the stress-optical coefficient of butadiene-styrene copolymers, at constant vinyl content, is a linear function of composition (Figure 9), a homogeneous blend of such polymers would be expected to exhibit the same stress-optical coefficient as a copolymer of the same styrene content. Actually, all blends examined show an elevation of Ka which increases with the breadth of the composition distribution (Table III). Such an elevation can be justified if the blends have a two- or multiphase domain structure in which the phases differ in modulus. If we consider the domains to be coupled either in series or in parallel (the true situation will be intermediate), then it is easily shown that... 

By definition, thermoplastics have limitations at elevated temperatures. It is in this particular property that fibrous glass can lead to remarkable improvements. However, a sharp division exists for reinforced thermoplastics. The various reinforced thermoplastics can be put in two groups relative to DTUL. These consist of amorphous and crystalline or semicrystalline polymers. The amorphous polymers such as styrene-acrylonitrile, polystyrene, polycarbonate, poly (vinyl chloride), and acrylo-nitrile-butadiene-styrene are generally limited to modest DTUL improvements, usually on the order of 20°F with 20% glass. However, crystalline polymers such as the nylons, linear polyethylene, polypropyl-... 

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... 

Fig. 1. US total sales and captive use of selected thermoplastic resins by major market for 2001. Major market volumes are derived from plastic resins sales and captive use data as compiled by VERIS Consulting, LLC and reported by the American Plastics Council s Plastic Industry Producers Statistics Group. Selected thermoplastics are low-density polyethylene, linear low-density polyethylene, high-density polyethylene, polypropylene, nylon, polyvinyl chloride, thermoplastic polyester, engineering resins, acrylonitrile-butadiene-styrene, styrene-acrylonitrile, other styrenics, polystyrene, and styrene butadiene latexes. (Data from ref. 25.)...

In regard to linear copolymers, the most common ones are ethylene-propylene, styrene-butadiene, acrylonitrile-butadiene, and acrylonitrile-butadiene-styrene [195], These materials are... 

LDPE, Low density polyethylene LLDPE, Linear low density polyethylene HDPE, High density polyethylene PP, Polypropylene PVC, Polyvinyl chloride GPS, General purpose polystyrene HIPS, High impact polystyrene SAN, Styrene acrylonitrile ABS, Acrylonitrile butadiene styrene PC, Polycarbonate PA, Polyamide PET, Polyethylene terephthalate. 

Includes high-, low-, and linear low-density polyethylene includes acrylonitrile-butadiene-styrene. SOURCE Statistics Canada. 

PP, polypropylene PS, polystyrene HDPE, high-density poylethylene EVA, ethylene vinyl acetate ABS, acrylonitrile-butadiene-styrene SMA, styrene maleic anhydride LDPE, low-density polyethylene LLDPE, linear low-density polyethylene. (From Ref. f)... 

Kerns, M.L. Henning, S.K. Synthesis and rheological characterization of branched versus linear solution styrene-butadiene rubber. Rubber Chem. Technol. 2002, 75, 299-308. http //www.dow.com/. 

Linear low-density polyethylene (LLDPE) and PS resins were the same as described previously (Chapter 21). The various block copolymers that were used as compatibilizers have also been described (I). A series of crystalline copolymers (Q series) was prepared by hydrogenation of diblock and triblock copolymers of styrene and butadiene [styrene-hydrogenated butadiene (SEB) and styrene-hydrogenated butadiene—styrene (SEBS)J (1). Triblock copolymers of styrene and butadiene [styrene-butadiene-styrene (SBS)] and a noncrystalline hydrogenated block copolymer (SEBS) (Kraton) were supplied by Shell Chemical Co. Diblock copolymers of styrene and butadiene [styrene-butadiene (SB) (Vector)] were obtained from Dexco Polymers. The characteristics of the resins are given in Table I. 

Fig. 7. Plots of oxygen uptake against time [333] (a) linear, polymers that show no induction period but absorb oxygen at a relatively constant rate (polymethylmethacrylate, polystyrene, polycarbonate) (b) autoretardant, polymers that exhibit no induction period but initially absorb oxygen at a relatively rapid rate, followed by a slower steady rate (polyethylene, polypropylene, nylons) (c) polymers that display autocatalytic behaviour (the modified acrylics, acrylonitrile—butadiene—styrene copolymer) (d) polymers that can be considered a combination of autocatalytic and autoretardant, (c) and (d) can be considered as autocatalytic, since the processes usually become autoretardant in the later stages of oxidation.

When a mixture of styrene and acrylonitrile is polymerized in the presence of a polybutadiene latex by an emulsion radical process, an acrylonitrile-butadiene-styrene (ABS) copolymer is obtained. This ABS copolymer is actually a mixture of (a) a graft copolymer which contains some of the styrene/acrylonitrile (ST/AN) copolymer chemically bound to the polybutadiene backbone, and (b) a random copolymer, conventionally designated as a linear copolymer, which is not bound to the polybutadiene backbone but which consists of the portion of the styrene/acrylonitrile monomer that has polymerized separately. 

---