Reinforcement glass fiber

Unfilled Flexible Mineral-filled Granular Glass-fiber- reinforced ... 

Fluorinated ethylene-propylene resin Poly(vinylidene fluoride) Ethylene-tetrafluoroethylene copolymer Ethylene- chlorotrifluoro- ethylene copolymer Cellulose- filled Glass-fiber- reinforced... 

Properties woodflour- and cellulose-filled Nitrile Unfilled Woodflour- filled Glass-fiber- reinforced Cellulose- filled Mineral- filled... 

Low viscosity 30% glass-fiber reinforced Poly(butylene terephthalate) Poly(ethylene terephthalate) ... 

Unfilled 30% glass-fiber-reinforced Unfilled 30% glass-fiber-reinforced... 

Low-density Medium-density High-density Ultra high-molecular-weight Glass-fiber- reinforced, high-density Ethylene-vinyl acetate copolymer... 

Properties Unfilled 20% glass-fiber- reinforced Unfilled 20% glass-fiber- reinforced Poly(ether sulfone) Poly(phenyl sulfone)... 

Poly(vinyl chloride) and poly(vinyl acetate) Poly(vinyl chloride), 15% glass-fiber-reinforced Chlorinated poly(vinyl chloride) Poly(vinyl butyral), flexible ... 

Glass-fiber-reinforced (increased stiffness and tensile strength) and mineral filled (reduced shrink and warp) grades also have been developed. 

The hand lay-up or spray-up process, used universally for the production of laminar composites incorporating glass fiber reinforcement, is most efficient for the manufacture of large parts, such as boats, bathtubs, tanks, architectural shapes, and recreational accessories. Resins intended for spray-up processes are usually modified with thixotropic additives, such as fumed siHca (1%), to reduce the risk of drainage when appHed over large vertical mold surfaces. Molds are also made from ERP for short-mn products usually surfaced with a tooling gel coat to provide consistent surface quaHty and appearance. 

The tensile and flexural properties as well as resistance to cracking in chemical environments can be substantially enhanced by the addition of fibrous reinforcements such as chopped glass fiber. Mechanical properties at room temperature for glass fiber-reinforced polysulfone and polyethersulfone are shown in Table 5. 

Table 5. Properties of Glass Fiber-Reinforced (GR) Polysulfone and Polyethersulfone...

Proprietary blend formulations based on polysulfone, polyethersulfone, and polyphenylsulfone are sold commercially by Amoco Corporation to meet various end use requirements. The blends based on polysulfone are sold under the MINDEL trademark. A glass fiber-reinforced blend based on PES is offered under the trade name RADEL AG-360. This offers most of the performance characteristics of 30% glass fiber-reinforced polyethersulfone but at a lower cost. Two blend product lines are offered based on PPSF. These are designated as the RADEL R-4000 and R-7000 series of products. The former is a lower cost alternative to RADEL R PPSF homopolymer offering most of the performance attributes unique to PPSF. The R-7000 series of resins have been formulated for use in aircraft interiors for civil air transport. They exhibit a very high degree of resistance to flammabihty and smoke release. 

Property ASTM method Unfilled Glass-fiber reinforced Mineral filled... 

Reinforced Thermoplastic Sheet. This process uses precombined sheets of thermoplastic resin and glass fiber reinforcement, cut into blanks to fit the weight and size requirements of the part to be molded. The blanks, preheated to a specified temperature, are loaded into the metal mold and the material flows under mol ding pressure to fiU the mold. The mold is kept closed under pressure until the temperature of the part has been reduced, the resin solidified, and demolding is possible. Cycle time, as with thermosetting resins, depends on the thickness of the part and the heat distortion temperature of the resin. Mol ding pressures are similar to SMC, 10—21 MPa (1500—3000 psi), depending on the size and complexity of the part. 

Some design factors, however, work against composites. For example, glass fiber-reinforced plastics generally have lower modulus (stiffness) than metals. Thickness and shape adjustments are requited where stiffness is a critical design requirement. With appropriate reinforcement, any modulus, even greater than that of metals, can be achieved. However, it may become expensive and uneconomical to do so. 

In the gas cleaning sections of spent acid or metaUurgical sulfuric acid plants, the weak acid scmbbing circuit is typicaUy handled by plastic or glass fiber reinforced plastic (ERP) pipe. The contaminants in weak acid usuaUy vary too greatly to aUow use of an economical aUoy. 

The avadabihty of PMDI also led to the development of polyurethane-modified isocyanurate (PUIR) foams by 1967. The PUIR foams have superior thermal stabiUty and combustibiUty characteristics, which extend the use temperature of insulation foams well above 150°C. The PUIR foams are used in pipe, vessel, and solar panel insulation glass-fiber-reinforced PUIR roofing panels having superior dimensional stabiUty have also been developed. More recently, inexpensive polyester polyols based on residues obtained in the production of dimethyl terephthalate (DMT) have been used in the formulation of rigid polyurethane and PUIR foams. 

Other. Vinyl acetate resins are useful as antishrinking agents for glass fiber-reinforced polyester mol ding resins (165). Poly(vinyl acetate)s are also used as binders for numerous materials, eg, fibers, leather (qv), asbestos, sawdust, sand, clay, etc, to form compositions that can be shaped with heat and pressure. Joint cements, taping compounds, caulks, and fillers are other uses. 

Sanitary ware, including tubs, showers, combined units, basins, and toilet tank, may be made of thermoformed ABS or acryHc sheet, molded glass-fiber-reinforced polyester, or cast acryHc resins. The glass-polyester type dominates the tub/shower market. It is possible to install the units as a two-component system, assembled in place. Gel coats may be of thermoformed decorative acryHc skins. To reduce the smoke generated by fire, methyl... 

Some of the common types of plastics that ate used ate thermoplastics, such as poly(phenylene sulfide) (PPS) (see Polymers containing sulfur), nylons, Hquid crystal polymer (LCP), the polyesters (qv) such as polyesters that ate 30% glass-fiber reinforced, and poly(ethylene terephthalate) (PET), and polyetherimide (PEI) and thermosets such as diaHyl phthalate and phenoHc resins (qv). Because of the wide variety of manufacturing processes and usage requirements, these materials ate available in several variations which have a range of physical properties. 

Rectifier housing with glass fiber-reinforced base, housing connection box, meter table, corrosion protection rectifier 10 A/20 V, terminal strips, cable terminal and wiring, completely installed DM 8500... 

---