Films, water soluble

Water-Soluble Films. Water-soluble films can be produced from such polymers as poly(vinyl alcohol) (PVOH), methylceUulose, poly(ethylene oxide), or starch (qv) (see Cellulose ethers Polyethers Vinyl polymers). Water-soluble films are used for packaging and dispensing portions of detergents, bleaches, and dyes. A principal market is disposable laundry bags for hospital use. Disposal packaging for herbicides and insecticides is an emerging use. 

Water-soluble molecules are often incorporated into sustained release film coats as pore forming agents to increase coat permeability. Pore forming agents thus provide a simple and precise means of controlling drug release rates through an insoluble film. Water-soluble... 

Bag-in-a-box Plastic bag in corrugated cardboard and polyvinyl alcohol film (water soluble) in corrugated cardboard. 

Various forms of chitin-based products are available for medical applications, such as finely divided powder, nonwoven fabrics, porous beads, lyophilized soft fleeces or gels, gauges, laminated sheets, and transparent films. Water-soluble derivatives of chitin in isotonic saline can be administered intramuscularly or intravenously. Certainly, there is considerable biochemical evidence linking NAG with the metabolism of the hexamines, which are assumed to originate and cross-link wound collagen. 

The solubility of TG treated films was compared to that of non treated films (Fig 3). Films obtained with deamidated gluten were soluble at 78% in water, the addition of putrescine didn t modify the film solubility (Fig 3). The action of transglutaminase induced a decrease in the film water solubility. The highest insolubility was obtained for a ratio putrescine / glutamine of 0.18 mole/mole and could be related to the formation of polymers of high molecular weight. 

Major polymer applications sizing agents, binders, protective colloids, photographic papers, toners, film, water-soluble laundry bags, seed tapes, sanitary pads, belts, printing rolls, controlled drug delivery, membranes... 

Fig. 18.6 shows a PVA film (water-soluble)—bentonite—HOPE sheet composite to improve surface adsorption performance. Fig. 18.7 shows water permeability with PVA him laminating. This research is ongoing. 

One may rationalize emulsion type in terms of interfacial tensions. Bancroft [20] and later Clowes [21] proposed that the interfacial film of emulsion-stabilizing surfactant be regarded as duplex in nature, so that an inner and an outer interfacial tension could be discussed. On this basis, the type of emulsion formed (W/O vs. O/W) should be such that the inner surface is the one of higher surface tension. Thus sodium and other alkali metal soaps tend to stabilize O/W emulsions, and the explanation would be that, being more water- than oil-soluble, the film-water interfacial tension should be lower than the film-oil one. Conversely, with the relatively more oil-soluble metal soaps, the reverse should be true, and they should stabilize W/O emulsions, as in fact they do. An alternative statement, known as Bancroft s rule, is that the external phase will be that in which the emulsifying agent is the more soluble [20]. A related approach is discussed in Section XIV-5. 

Mixing fatty acids with fatty bases can dissolve films as the resulting complexes become water-soluble however, in some cases the mixed Langmuir film is stabilized [128]. The application of an electric field to a mixed lipid monolayer can drive phase separation [129]. 

Polyaniline (PANI) can be formed by electrochemical oxidation of aniline in aqueous acid, or by polymerization of aniline using an aqueous solution of ammonium thiosulfate and hydrochloric acid. This polymer is finding increasing use as a "transparent electrode" in semiconducting devices. To improve processibiHty, a large number of substituted polyanilines have been prepared. The sulfonated form of PANI is water soluble, and can be prepared by treatment of PANI with fuming sulfuric acid (31). A variety of other soluble substituted AJ-alkylsulfonic acid self-doped derivatives have been synthesized that possess moderate conductivity and allow facile preparation of spincoated thin films (32). 

Spray Drying. Spray-dry encapsulation processes (Fig. 7) consist of spraying an intimate mixture of core and shell material into a heated chamber where rapid desolvation occurs to thereby produce microcapsules (24,25). The first step in such processes is to form a concentrated solution of the carrier or shell material in the solvent from which spray drying is to be done. Any water- or solvent-soluble film-forming shell material can, in principle, be used. Water-soluble polymers such as gum arable, modified starch, and hydrolyzed gelatin are used most often. Solutions of these shell materials at 50 wt % soHds have sufficiently low viscosities that they stiU can be atomized without difficulty. It is not unusual to blend gum arable and modified starch with maltodextrins, sucrose, or sorbitol. 

PyCis usuaHy expressed in percentage, but the % sign is often omitted. Although many additives in the paint formulation are nonvolatile, they are often omitted from this calculation, because they represent a smaH fraction of the volume of a newly formed paint film and, in exterior paints, are often water-soluble materials leached out by rainfaH, and therefore wHl probably not factor into the long-term performance of the paint film. 

Aquatic Toxicity. The standard tests to measure the effect of substances on the aquatic environment are designed to deal with those that are reasonably soluble ia water. Unfortunately this is a disadvantage for the primary phthalates because they have a very low water solubiUty (ca 50 p.g/L) and this can lead to erroneous test results. The most common problem is seen ia toxicity tests on daphnia where the poorly water-soluble substance forms a thin film on the water surface within which the daphnia become entrapped and die. These deaths are clearly not due to the toxicity of the substance but due to unsuitable test design. 

Functional derivatives of polyethylene, particularly poly(vinyl alcohol) and poly(acryLic acid) and derivatives, have received attention because of their water-solubility and disposal iato the aqueous environment. Poly(vinyl alcohol) is used ia a wide variety of appHcations, including textiles, paper, plastic films, etc, and poly(acryLic acid) is widely used ia detergents as a builder, a super-absorbent for diapers and feminine hygiene products, for water treatment, ia thickeners, as pigment dispersant, etc (see Vinyl polymers, vinyl alcohol polymers). 

Films or membranes of silkworm silk have been produced by air-drying aqueous solutions prepared from the concentrated salts, followed by dialysis (11,28). The films, which are water soluble, generally contain silk in the silk I conformation with a significant content of random coil. Many different treatments have been used to modify these films to decrease their water solubiUty by converting silk I to silk II in a process found usehil for enzyme entrapment (28). Silk membranes have also been cast from fibroin solutions and characterized for permeation properties. Oxygen and water vapor transmission rates were dependent on the exposure conditions to methanol to faciUtate the conversion to silk II (29). Thin monolayer films have been formed from solubilized silkworm silk using Langmuir techniques to faciUtate stmctural characterization of the protein (30). ResolubiLized silkworm cocoon silk has been spun into fibers (31), as have recombinant silkworm silks (32). 

Water-borne adhesives are preferred because of restrictions on the use of solvents. Low viscosity prepolymers are emulsified in water, followed by chain extension with water-soluble glycols or diamines. As cross-linker PMDI can be used, which has a shelf life of 5 to 6 h in water. Water-borne polyurethane coatings are used for vacuum forming of PVC sheeting to ABS shells in automotive interior door panels, for the lamination of ABS/PVC film to treated polypropylene foam for use in automotive instmment panels, as metal primers for steering wheels, in flexible packaging lamination, as shoe sole adhesive, and as tie coats for polyurethane-coated fabrics. PMDI is also used as a binder for reconstituted wood products and as a foundry core binder. 

Ethylene oxide reacts with poly(vinyl alcohol) under normal ethoxylation conditions (135—142). The resulting products have properties that make them usehil as cold-water-soluble films. 

---