Controls, operator

For an effective control operation, the transducer with orthogonal coils has been coupled to a SFT 6000N control equipment, the results being sampled and quantized on 12 bits, stored and post-processed. 

This big increase in speed has not been without cost. The everyday machine codes and high-level languages (Fortran, Pascal, C, etc.) used to control operations in a standard computer are inappropriate for parallel processing, which needs its own instruction set and has led to the development of special languages for use with the transputer. 

G. W. Gupton Jr., HHAC Controls, Operation and Maintenance, Fairmont Press, Lilbum, Ga., 1987. 

The various fumigants often exhibit considerable specificity toward insect pests, as shown in Table 8. The proper choice for any control operation is determined not only by the effectiveness of the gas but by cost safety to humans, animals, and plants flammabdity penetratabdity effect on seed germination and reactivity with furnishings. The fumigants may be used individually or in combination. Carbon tetrachloride has been incorporated with carbon disulfide, ethylene dichloride, or ethylene dibromide to decrease flammability, and carbon dioxide is used with ethylene oxide for the same purpose. 

The electric furnace is an alternative to the reverberatory furnace in environmentally sensitive areas where electricity costs are not too high. The electric furnace is versatile, produces small volumes of effluent gases, and the SO2 concentration can be easily controlled. Operating costs, however, are high. 

Improvements in the abiUty to control operating conditions and in contractor designs have allowed a steady reduction in the number of purification steps required. The THORP faciUty, commissioned as of 1994 in the U.K., uses only a single purification step. 

Fig. 20. Example of constraint control operating window for a distillation column, where (-----) is the vessel pressure limit, and ( ) represents constant...

D. A. Kuemmel and R. M. H2csPo-, Accident Analysis of Ice Control Operations, presented at the Third International Symposium on Snow Removal and Ice Control Technology, Minneapolis, Minn., 1992. 

Most sulfonation plants monitor and control operations by computer. Sulfur-buming catalytic SO -generating equipment may require a 1—2 h stabilization period on startup. The unit can be kept in a standby position by maintaining heat to the unit when it is off-line. Liquid SO -based sulfonation plants do not require such a stabilization period and hence are more flexible to operate than sulfur-buming sulfonation plants. 

Computer Control. The use of computer systems to control the operation of submerged arc furnaces, including calcium carbide, has been successfully demonstrated in the United States (see Expert systems Process control). Operations direcdy under control are mix batching, electrode position and sHp control, carbide gas yield, power control, and cooling water systems. Improvements in energy usage, operating time, and product quaHty are obtained. 

The processing type refers to how the copper circuits are fabricated. These classes differ in stabiHty, ease of regeneration and control, operating... 

Multiloop Controllers The multiloop controller is a DCS network device that uses a single 32-bit microprocessor to provide control functions to many process loops. The controller operates independent of the other devices on the DCS network andTcan support From 20 to 500 loops. Data acquisition capability for up to 1000 analog and discrete I/O channels or more can also be provided by this controller. 

The speed control operates the governing valve to maintain steam flow commensurate with load demand while holding speed essentially constant. For sudden load changes there will be a short-time overshoot, and a special case is the instantaneous loss of load, load dump at full load. The usual specification states that the overshoot on load dump must not exceed 9 to 10 percent of rated speed. The settled speed rise will of course be equal to the regulation, 4 or 6 percent for a NEMA Class C or B governor and less than I percent for Class D. 

Basic process control system (BPCS) loops are needed to control operating parameters like reactor temperature and pressure. This involves monitoring and manipulation of process variables. The batch process, however, is discontinuous. This adds a new dimension to batch control because of frequent start-ups and shutdowns. During these transient states, control-tuning parameters such as controller gain may have to be adjusted for optimum dynamic response. 

Manual mode control operation is very common leading to increased potential for human error. 

The problem could be maintenance, operation, or design, or a combination of any or all these factors. In all honesty, you should never. see this set of evidence marks because it indicates a lack of control. Now because the mechanic cannot control operational problems or design problems, the first phase to correct this situation is to control the mechanical maintenance factors, like alignment, proper bolting and torque. sequences, be sure shafts are straight and round, and dynamically balance all rotary components. Reinstall the pump and wait for the next failure. Once the maintenance factors are under control, there should appear a clear vision and path to resolve any operational and/or design weaknesses. 

The components of a quality assurance program are designed to serve the two functions just mentioned—control and assessment. Quality control operations are defined by operational procedures, specifications, calibration procedures, and standards and contain the following components ... 

Startup description. When the unit is prepared to start, the Ready to Start lamp will be lit. With local control, operating one of the following push buttons will initiate a start ... 

Environmental management system documentation Document control Operational control Emergency preparedness and response Checking and corrective action... 

Process Detailed Design Detailed specification based on concept design Minimize number of possible leak paths Make plant friendly to control, operate, and maintain Avoid or simplify hazardous activities such as sampling, loading and unloading Process conceptual design and codes/standards and procedures Experience on past projects/designs... 

A process waste heat boiler was damaged when the control operator inadvertently closed the cooling water valve when he intended to open it. The manual control knob turned in the opposite direction from most of the other valves in the plant—the L, cooling water valve was air to close—most control valves were air... 

In all such laboratory studies, plant conditions and compositions should be employed as far as possible. Agglomeration rates tend to increase with the level of supersaturation, suspension density and particle size (each of which will, of course, be related but the effects may exhibit maxima). Thus, agglomeration may often be reduced by operation at low levels of supersaturation e.g. by controlled operation of a batch crystallization or precipitation, and the prudent use of seeding. Agglomeration is generally more predominant in precipitation in which supersaturation levels are often very high rather than in crystallization in which the supersaturation levels are comparatively low. 

Formerly known as Chemical Manufacturers Association (CMA). A trade association of chemical manufacturers, representing more than 90 percent of the production for basic industrial chemicals in the US. Administers research in areas significant to chemical manufacturing such as air and water pollution control operates Chemical Transportation Emergency Center (CHEMTREC) to control and report chemical accidents. ACC is organized by industrial groups and also by issue groups that sen>e as coordinators and advocators in their fields of specializations. 

Human Factors Engineering/Ergonomics approach (control of error by design, audit, and feedback of operational experience) Occupational/process safety Manual/control operations Routine operation Task analysis Job design Workplace design Interface design Physical environment evaluation Workload analysis Infrequent... 

Astley, J., Shepherd, A., Whitfield, D. (1990). A Review of UK and International I owledge and Practice in the Selection of Process Control Operators. In E. J. Lovesey (Ed.), Ergonomics Setting Standards for the 90 s. Contemporary Ergonomics, 1990. London Taylor and Francis. 

Manual (for seasonal changes only) or automatic pitch control operated by air-motor on fan blades. 

Using the basic performance data given in Table 4-110 for the 6-f--in. outside diameter turbine motor with 212 stages, determine the stall torque, maximum horsepower and pressure drop for this motor if only one motor section with 106 stages were to be used for a deviation control operation. Assume the same circulation flow rate of 400 gal/min, but a mud weight of 14 Ib/gal is to be used. 

---