Chemical industry categories

The effluent standards require two levels of treatment best practicable control technology (BPCT) and best available control technology (BACT). New standards covering additional industries are stiU being issued. Of special concern to the chemical industry are the following Hsted categories ... 

In general, DOT safety regulations fall into two categories. The first pertains to qualifications and hours of service of carrier employees and the safety of transport operations and equipment. The second, of special concern to the chemical industry, pertains to the transportation of hazardous materials and related commodities. 

The sources, amounts, and composition of injected hazardous wastes are a matter of record, because the Resource Conservation and Recovery Act (RCRA)5,14 requires hazardous waste to be manifested (i.e., a record noting the generator of the waste, its composition or characteristics, and its volume must follow the waste load from its source to its ultimate disposal site). The sources and amounts of injected hazardous waste can be determined, therefore, based on these records. Table 20.2 shows the estimated volume of deep-well-injected wastes by industrial category.3 More than 11 billion gallons of hazardous waste were injected in 1983. Organic chemicals (51%) and petroleum-refining and petrochemical products (25%) accounted for three-quarters of the volume of injected wastes that... 

Previous production of pentachlorophenol, as well as the bleaching process in pulp and paper mills, has been shown to be a major source. Changes in industrial processes have resulted in a reduction of PCDD/PCDFs concentration in products. Whereas in the past the chemical industry and, to a lesser extent, the pulp and paper industry were considered to be the main sources of PCDD/PCDFs (and also the cause of many of today s contaminated sites in several industrialized countries), today s dioxin input is mainly due to thermal processes. There is still a considerable focus on waste incineration but, owing to requirements for dioxin reduction in stack gases set by several national authorities, the importance of this category has declined during the last years. Examples can be seen especially in the European emission inventories... 

There are no occupational exposure limits for many hazardous substances which may require control of inhalation exposures. The necessary data and other resources required for setting such limits is restricted and unlikely to match the potential demand. A hazard categorisation scheme was, therefore, developed for application within the chemical industry. The scheme used readily-available information on toxicological endpoints to place hazardous substances into a limited range of hazard categories, expressed as Occupational Exposure Bands. These Bands could be used as a basis for risk assessment and the selection of appropriate control regimes. 10 refs. EUROPEAN COMMUNITY EUROPEAN UNION UK WESTERN EUROPE... 

E.H. Hurst s overview introduced several themes pursued by other chemical industry speakers. The Dow Chemical Company s E.H. Blair analyzed the problem of setting priorities for testing the 55,000 existing chemicals listed in the TSCA inventory for their effects on health and the environment. Resources for such testing are not unlimited. A systematic classification was made of these substances by production volume. The 9.5% of these substances which account for 99.9% of reported production were divided further into categories such as organic, inorganic, and polymeric. 

We use sidebar 3.2, an outline of the major categories of the chemical industry, to identify the nation s vulnerabilities to terrorist attack on our chemical infrastructure. Virtually all chemical use, storage, and manufacturing in the United States fits into one of these categories. 

Disulfoton is regulated by the Clean Water Effluent Guidelines as state in Title 40, Sections 400-475, of the Code of Federal Regulations. The point source category for which disulfoton has a specific Regulatory Limitation is the organic pesticide chemicals industry (EPA 1978a). 

The data required for the risk assessment in relation to human health can be categorized as data on the identity of the substance, its physico-chemical and toxicological properties, and on exposure. The minimum data set required for a risk assessment depends on the chemical use category (industrial chemical, pesticide, biocide, food additive, food contact material, etc.), the regulation involved, and the goal of the risk assessment. This chapter will focus on the data used in the hazard assessment. 

The products offered by the fine-chemical industry fall into two broad categories (1) exclusives and standard or (2) catalog products. Serviceintensive exclusives , provided mostly through contract research or custom manufacturing arrangements, prevail in business with life science companies standards prevail in other target markets. 

The category Enzymes as industrial catalysts , including the starch-processing, antibiotics and the fine-chemicals industry, is covered in chapter 4. 

The use of solvents in the chemical industry and in the chemical-related industries is ubiquitous. Beyond chemical industries, solvent use has become an integral part of life in the twenty-first century. In 1991, the production of the 25 most commonly used solvents was more than 26 million tons per year. According to EPCRA section 313 data, of the chemicals and chemical categories tracked by the program in 1994, five of the top 10 chemicals released or disposed of were solvents, and included methanol, toluene, xylene, methyl ethyl ketone, and dichloromethane. The total quantity of these chemicals released or disposed of was over 687 million pounds, which accounts for 27% of the total quantity of TRl-listed chemicals released and disposed of in that year (Sullivan, 1997). 

Materials that have had prior human use/exposure in food and cosmetics, or from the chemical industry, can be categorized as essentially new excipients. Such previous exposure is likely to be of help for oral and topical use excipient development. Excipients that have had established medicinal product use but are being used by a different dose route and/or chemically modified to enhance their properties are also likely to belong to this category. 

The management challenges in each of these major categories differ considerably. In Chapter 3 we will return to these and describe the potential strategic choices for the chemical industry. 

The CWA has established discharge requirements for 129 individual toxic pollutants (VOCs, pesticides, metals and corrosives), known as priority pollutants, and conventional pollutants for 34 industrial categories (EPA, 1998b). Appendix 2 lists these pollutants, which are either individual chemicals or groups of chemicals of a similar nature. Aquatic toxicity testing and temperature measurements also often included into NPDES permits. 

The selective oxidation of organic molecules is one of the most important processes used in the chemical industry. Its reactions fall into two broad categories (i) gas-phase oxidation of hydrocarbons (alkanes, alkenes) to oxygenated products and (ii) further oxidation of molecules containing one or more oxygen atoms (mainly in the liquid phase). 

---