Acceptable performance

In the future it will be difficult to avoid deterioration of certain characteristics such as viscosity, asphaltene and sediment contents, and cetane number. The users must employ more sophisticated technological means to obtain acceptable performance. Another approach could be to diversify the formulation of heavy fuel according to end use. Certain consuming plants require very high quality fuels while others can accept a lower quality. 

Biaxial Orientation. Many polymer films require orientation to achieve commercially acceptable performance (10). Orientation may be uniaxial (generally in the machine direction [MD]) or biaxial where the web is stretched or oriented in the two perpendicular planar axes. The biaxial orientation may be balanced or unbalanced depending on use, but most preferably is balanced. Further, this balance of properties may relate particularly to tensile properties, tear properties, optical birefringence, thermal shrinkage, or a combination of properties. A balanced film should be anisotropic, although this is difficult to achieve across the web of a flat oriented film. 

Very substantial advances have been made in terms of improvements in electrode stmctures and increases in the Pt utili2ation as illustrated in Figure 1. It appears that Pt loadings of less than 0.2 mg Pt/cm are adequate to obtain acceptable performance in PEFCs using pure H2 as the fuel (see Thin films). Whereas early electrodes contained 4 mg Pt/cm, the most recent developments in electrode fabrication have permitted Pt loadings to be reduced to 0.13 mg Pt/cm in a thin-film stmcture, while maintaining high performance. 

For high temperature fuel ceUs, there is stiU a strong need to develop lower cost materials for ceU components. In the case of SOFCs, improved fabrication processes and materials that permit acceptable performance in fuel ceUs at lower operating temperatures are also highly desirable. 

Cured amino resins are far too brittle to be used alone as surface coatings for metal or wood substrates, but in combination with other film formers (alkyds, polyesters, acryUcs, epoxies) a wide range of acceptable performance properties can be achieved. These combination binder coating formulations cure rapidly at slightly elevated temperatures, making them well suited for industrial baking appHcations. The amino resin content in the formulation is typically in the range of 10—50% of the total binder soHds. 

Additional definition of the operative mechanisms can obviate the need for the larger unit. It maybe possible to assess limitations in a smaller unit that has only a few injection points on the distributor. The unit could be used to evaluate distributor designs that permit a wide range of acceptable operating conditions. However, if the acceptable range proves smaller than desired, the larger pilot unit would then be needed to estabUsh acceptable performance. 

Tallow [61789-97-7] is the fat obtained as a by-product of beef, and to a lesser degree sheep processing, and is the most commonly utilized animal fat in the manufacturing of soaps. The high content of longer chain length fatty acids present in tallow fat necessitates the addition of other oils, such as coconut oil, in order to produce a bar with acceptable performance. 

In distillation towers, entrainment lowers the tray efficiency, and 1 pound of entrainment per 10 pounds of liquid is sometimes taken as the hmit for acceptable performance. However, the impact of entrainment on distiUation efficiency depends on the relative volatility of the component being considered. Entrainment has a minor impact on close separations when the difference between vapor and liquid concentration is smaU, but this factor can be dominant for systems where the liquid concentration is much higher than the vapor in equilibrium with it (i.e., when a component of the liquid has a very lowvolatiUty, as in an absorber). 

The case studies that follow have mainly come from live product development projects in industry. Whilst not all case studies require the methodology to predict an absolute capability, a common way of applying CA is by evaluating and comparing a number of design schemes and selecting the one with the most acceptable performance measure, either estimated Cp, assembly risk or failure cost. In some cases, commercial confidence precludes the inclusion of detailed drawings of the components used in the analyses. CA has been used in industry in a number of different ways. Some of these are discussed below ... 

Capital investment decisions are best made within the context of a life-cycle cost analysis. Life-cycle cost analysis focuses on the costs incurred over the life of the investment, assuming only candidate investments are considered that meet minimally acceptable performance standards in terms of the non-inonetary impacts of the investment. Using life-cycle analysis, the capital investment decision takes into account not just the initial acquisition or purchase cost, but maintenance, energy use, the expected life of the investment, and the opportunity cost of capital. When revenue considerations are prominent, an alternative method of analysis such as net benefit or net present value may be preferred. 

On the other hand the tower should be able to operate at changing vapor and liquid loads wthout serious upset. In this tjpe of tray the designer has a selection of holes, in this case For the top select 1,100 to 1,500 for the bottoms, select 1,300 to 1,750, and still expect acceptable performance. 

This number is in the range of acceptable performance for bottom section and should be punched. If performance indicates fewer holes are preferable, blanking strips can be added (or even added before the trays are installed). The top trays definitely require blanking of holes. 

Figure 11-13 is convenient for preparing an initial specification for competitive inquiry, as well as for summarizing the final accepted performance and specifications. In using the specification sheet, supplemental notes should he included to state ... 

The primary indicator of acceptable performance is the quality of the product delivered by the mixer. Although there is no direct way to measure this indicator, feedback from the quality assurance group should be used to verify that acceptable performance levels are attained. 

On occasion, results from one of the participating laboratories will fail to meet established acceptability criteria. In those cases, acceptance or rejection of the method is determined by the CVM based on overall method performance. For example, a method that has borderline but acceptable performance for both precision and accuracy at two of three participating laboratories and fails badly at a third laboratory would probably fail. A method that was a borderline failure in one laboratory but easily passed in the other laboratories could be accepted. 

Few laboratories have developed their own facilities for packing conventional and small bore columns, preferring to rely on commercial manufacturers for their needs. This is understandable since packed columns containing any common phase can be obtained at an acceptable cost and with a guarantee of acceptable performance and stability. Column packing generally requires access to equipment not readily available in all laboratories and... 

The treatment of recurrent disease depends on the time to recurrence. If the time to recurrence is less than 6 months, second-line therapy should be considered if the patient has an acceptable performance status (see Patient Care and Monitoring ). The most widely accepted second-line therapies in SCLC are topotecan alone or CAV [cyclophosphamide, doxorubicin (Adriamycin), vincristine]. Relapses occurring more than 6 months after treatment warrant a repeat of the initial regimen. Poor performance status patients (3—4) typically are treated with palliative care therapies. 

In addition to glass electrodes [159], the pH sensors incorporated in the catheter for esophageal pH monitoring were reported to be mostly antimony electrodes such as the Slimline from Medtronic Inc. [95, 158, 164], In a recent study, Pandolfino el al. [33] compared the accuracy of the Slimline antimony pH monitoring system to that of a conventional glass electrode catheter pH system during ambulatory conditions in 18 patients. They reported that the antimony electrodes had acceptable performance... 

Standards provide a base for a uniform system of accepted performance such as those found in engineering practice standards, material standards, and test standards. Hydrogen standards are typically written under a consensus process by technical committees (TC) representing a cross section of interested parties and issued in the United States, for example, by organizations such as the American Society of Mechanical Engineers (ASME) for pressure vessels, pipelines, and piping the Compressed Gas Association (CGA) for pressure vessel operation and maintenance and the Underwriters Laboratories (UL) for product certification. 

---