Water separator

In a conventional gasoline containing hydrocarbons or even ethers, the presence of water is not a problem in fact, water is totally soluble up to about 50 ppm at ambient temperature. Beyond this value water separates without affecting the hydrocarbon phase and the water leg can be withdrawn if necessary. On the other hand, in the presence of alcohols (ethanol and especially methanol), trace amounts of water can cause a separation of two phases one is a mixture of water and alcohol, the other of hydrocarbons (Cox, 1979). 

For combined cycle turbines Single lubrication system Low pour point Extreme pressure and anti-wear properties Hydrolysis stability Water separation... 

Water separated from oil usually contains small amounts of oil which have to be removed before the water can be released to the environment. Specifications are getting tighter but standards ranging from 10-100 ppm (parts per million) oil in wafer before disposal are currently common. In most areas 40 ppm of oil in water is the legal requirement, i.e. 40 mg / litre. 

A fresh sample of dimethyl sulphate should be employed an old sample, or one that has been frequently exposed to the air, should be shaken with water, separated, dried over sodium sulphate, and distilled (b.p. 188"). 

In the Schotten-Baumann method of benzoylation, the hydroxyl- or amino-compound (or a salt of the latter) is dissolved or suspended in an excess of 10% aqueous sodium hydroxide solution, a small excess (about 10% more than the theoretical amount) of benzoyl chloride is then added and the mixture vigorously shaken. Benzoylation proceeds smoothly under these conditions, and the solid benzoyl compound, being insoluble in water, separates out. The sodium hydroxide then hydrolyses the excess of benzoyl chloride, giving sodium... 

Bromoform. Commercial bromoform should be shaken thoroughly with water, separated, dried over powdered anhydrous sodium sulphate and then fractionally distilled under reduced pressure using a water-condenser. It should be stored in a dark cupboard. It is an excellent solvent, has the advantage of a high Constant, and very seldom causes association of the solute. 

The success of this preparation depends upon the use of the apparatus (1) depicted in Fig.///, 57, 1, which permits of the automatic separation of the water produced in the reaction this will be termed a water-separator tube. Convenient dimensions for students preparations are indicated in the diagram. Determine the volume v of the tube up to the neck, i.e., between A and B, by adding water from a burette. The quantity of water which should be eliminated, assuming a quantitative conversion of the alcohol into the ether, may be computed from the equation ... 

Di-n-hexyl ether. Use 50 g. (61 ml.) of n-hexyl alcohol (b.p. 156-157°) and 6 g. (3-5 ml.) of concentrated sulphuric acid, and heat until the temperature rises to 180°. Pour the reaction mixture into water, separate the upper layer, wash it twice with 5 per cent, sodium hydroxide solution, then with water, and dry over anhydrous potassium carbonate. Distil from a 50 ml. Claisen flask, and collect the fractions of b.p. (i) 160-221° (17 g.), and (u) 221-223° (17 g.). Reflux fraction (i) with 4 g. of sodium and distil from the excess of sodium 9 - 5 g. of fairly prure n-hexyl ether, fraction (iii), are thus obtained. Combine fractions (ii) and (iii) and distil from a little sodium collect the pure n-hexyl ether (19 g.) at 221 - 5-223°. 

By refluxing a mixture of the acid (1 mol), alcohol (3-4 mols), dry benzene (375 ml.) and concentrated sulphuric acid (58-60 g.). The ester as formed passes into the benzene layer. Upon the addition of water, separating the benzene layer, and distilling the latter (after washing and dr3dng), benzene and alcohol pass over first, followed by the ester, for example ... 

Place a mixture of 53 g. of A.R. lactic acid (85-88 per cent, acid), 75 g. (85-5 ml.) of commercial anhydrous isopropyl alcohol, 300 ml. of benzene and 20 g. of Zeo-Karb 225/H (1) in a 700 ml. bolt-head flask, equipped with an automatic water separator (e.g., a large modified Dean and Stark apparatus with a stopcock at the lower end, see Fig. Ill, 126, 1) carrying an efficient reflux condenser at its upper end, and a mercury-sealed stirrer (alternatively, the hquid-sealed stirrer shown in Fig. 11,7,11, c. may be used). Reflux the mixture, with stirring, on a steam bath for 5 hours or until water no longer collects in appreciable amount in the water separator run off the water from time to time. Filter off the resin at the pump and wash it with two 25 ml. portions of benzene. Shake the combined filtrate and washings with about 5 g. of precipit-ated calcium... 

Furfuryl acetate. Reflux a mixture of 39 2 g. (34-8 ml.) of redistilled furfuryl alcohol, 48 g. of glacial acetic acid, 150 ml. of benzene and 20 g. of Zeo-Karb 225/H in a 500 ml. bolt-head flask, using the apparatus described under iaoPropyl Lactate. After 3 hours, when the rate of collection of water in the water separator is extremely slow, allow to cool, separate the resin by suction filtration, and wash it with three 15 ml. portions of benzene. Remove the benzene, etc., from the combined filtrate and washings under reduced pressure (water pump) and then collect the crude ester at 74-90°/10 mm. a small sohd residue remains in the flask. Redistil the crude ester from a Claisen flask with fractionating side arm pure furfuryl acetate passes over at 79-80°/17 mm. The yield is 14 -5 g. 

Place 200 g, (250 ml.) of rectified spirit in a 1-litre round-bottomed flask fitted with a reflux condenser. Cool in ice and run in, slowly and with frequent shaking, 200 g. (109 ml.) of concentrated sulphuric acid. Add 83 g. (104 ml.) of -butyl cyanide (Section 111,113) to the mixture and reflux the whole for 10 hours. Allow to cool, pour the reaction mixture into ice water, separate the upper layer of ester and alcohol, and dry over anhydrous magnesium or calcium sulphate. Distil through a fractionating column and collect the ethyl n-valerate at 143-146°. A further amovmt of the pure ester may be obtained by redrying the fraction of low boiling point and redistilling. The yield is 110 g. 

Dissolve 57 g. of dry malonic acid in 92 5 ml. of dry P3rridine contained in a 500 ml. round-bottomed flask, cool the solution in ice, and add 57 g. (70 ml.) of freshly distilled n-heptaldehyde (oenanthol) with stirring or vigorous shaking. After a part of the aldehyde has been added, the mixture rapidly seta to a mass of crystals. Insert a cotton wool (or calcium chloride) tube into the mouth of the flask and allow the mixture to stand at room temperature for 60 hours with frequent shaking. Finally, warm the mixture on a water bath until the evolution of carbon dioxide ceases (about 8 hours) and then pour into an equal volume of water. Separate the oily layer and shake it with 150 ml. of 25 per cent hydrochloric acid to remove pyridine. Dissolve the product in benzene, wash with water, dry with anhydrous magnesium sulphate, and distil under reduced pressure. Collect the ap-nonenoic acid at 130-13272 mm. The yield is 62 g. 

Place 32 g. of potassium ethyl xanthate (Section 111,166) and 50 ml. of absolute ethyl alcohol in a 500 ml. round-bottomed flask provided with a double surface condenser. Add 32 g. (16-5 ml.) of ethyl iodide. No reaction appears to take place in the cold. Heat on a water bath for 3 hours a reaction sets in within 15 minutes and the yellow reaction mixture becomes white owing to the separation of potassium iodide. Add about 150 ml. of water, separate the lower layer, and wash it with water. Dry it with anhydrous calcium chloride or anhydrous calcium sulphate and distil from a 50 ml. Claisen flask. Collect the ethyl S-ethyl xanthate at 196-198°. The yield is 23 g. 

This product is sufficiently pure for the preparation of phenylacetic acid and its ethyl ester, but it contains some benzyl tso-cyanide and usually develops an appreciable colour on standing. The following procedure removes the iso-cyanide and gives a stable water-white compound. Shake the once-distilled benzyl cyanide vigorously for 5 minutes with an equal volume of warm (60°) 60 per cent, sulphuric acid (prepared by adding 55 ml. of concentrated sulphuric acid to 100 ml. of water). Separate the benzyl cyanide, wash it with an equal volume of sa+urated sodium bicarbonate solution and then with an equal volume of half-saturated sodium chloride solution- Dry with anhydrous magnesium sulphate and distil under reduced pressure. The loss in washing is very small (compare n-Butyl Cyanide, Section 111,113, in which concentrated hydrochloric acid is employed). 

Place 75 g. (74 ml.) of benzyl cyanide (Section IV,160), 125 g. (153 ml.) of rectifled spirit and 150 g. (68 ml.) of concentrated sulphuric acid in a 750 ml. round-bottomed flask, fitted with an efficient reflux condenser. Reflux the mixture, which soon separates into Wo layers, gently for 8 hoius, cool and pour into 350 ml. of water. Separate the upper layer. Dissolve it in about 75 ml. of ether (1) in order to facilitate the separation of the layers in the subsequent washing process. Wash the ethereal solution carefully with concentrated sodium bicarbonate solution until effervescence ceases and then with water. Dry over 10 g. of anh3 drous magnesium sulphate for at least 30 minutes. Remove the solvent with the aid of the apparatus shown in Fig. II, 13, 4 and distil from an air bath (Fig. II, 5, 3). The ethyl phenylacetate passes over at 225-229° (mainly 228°) as a colourless liquid the yield is 90 g. Alternatively, the residue after removal of the ether may be distilled in a Claisen flask under diminished pressm (Fig. II, 20, 1) collect the ester at 116-lI8°/20 mm. 

The alcohol may be purified by conversion into the calcium chloride addition compound. Treat it with anhydrous calcium chloride much heat is evolved and the addition compound is formed. After several hours, remove any oil which has not reacted by washing with petroleum ether (b.p. 60-80°). Decompose the solid with ice water, separate the alcohol, dry and distil. 

Amino-5-methylthiazole. Suspend 76 g. of thiourea in 200 ml. of water in a 500 ml. three-necked flask equipped as in the preceding pre paration. Stir and add 92 -5 g. (80 ml.) of monochloroacetone (1) over a period of 30 minutes. The thiourea dissolves as the reaction proceeds and the temperature rises. Reflux the yellow solution for 2 hours. To the cold solution immersed in an ice bath add, with stirring, 200 g. of solid sodium hydroxide. Transfer to a separatory funnel, add a little ice water, separate the upper oil layer and extract the aqueous layer with three 100 ml. portions of ether. Dry the combined oil and ether extracts with anhydrous magnesium sulphate, remove the ether by distillation from a steam bath, and distil the residual oil under diminished pressure. Collect the 2-amino-5-methylthiazole at 130-133°/18 mm. it solidifies on coohng in ice to a solid, m.p. 44-45°. The yield is 84 g. 

The diethyl fumarate is readily prepared as follows. Reflux a mixture of 146 g. of fumaric acid (Section 111,143), 185 g. (236 ml.) of absolute ethanol, 450 ml. of boizene and 20 g. of concentrated sulphuric acid for 12 hours. Pour into a large volume of water, separate the benzene layer, wash successively with water, saturated lodium bicarbonate solution and water, dry with anhydrous magnesium sulphate, and remove the solvent on a steam bath. Distil the residue and collect the diethyl fumarate at 213-215° the yield is 150 g. 

Methyl crotonate. Purify commercial crotonic acid by distiUing 100 g. from a 100 ml. Claisen flask attached to an air condenser use an air bath (Fig. II, 5, 3). The pure acid passes over at 180-182° and crystallises out on cooling, m.p. 72-73° the recovery is about 90 per cent. Place 75 g. of absolute methyl alcohol, 5 g. (2 -7 ml.) of concentrated sulphuric acid and 50 g. of pure crotonic acid in a 500 ml. round-bottomed flask and heat under reflux for 12 hours. Add water, separate the precipitated ester and dissolve it in ether wash with dilute sodium carbonate solution until effervescence ceases, dry with anhydrous magnesium sulphate, and remove the ether on a water bath. Distil and collect the methyl crotoiiato at 118-120° the yield is 40 g. 

Introduce a solution of 100 g. of sodium bisulphite in 200 ml. of water and continue the stirring, preferably for 10 hours with exclusion of air. A thick precipitate separates after a few minutes. Collect the bisulphite compound by suction filtration, wash it with ether until colourless, and then decompose it in a flask with a lukewarm solution of 125 g. of sodium carbonate in 150 ml. of water. Separate the ketone layer, extract the aqueous layer with four 30 ml. portions of ether, dry the combined organic layers over anhydrous magnesium sulphate, remove the ether at atmospheric pressure, and distil the residual oil under reduced pressure from a Qaisen flask with fractionating side arm (Fig. II, 24, 5). Collect the cyclo-heptanone at 64r-65°/12 mm. the yield is 23 g. 

The purified commercial di-n-butyl d-tartrate, m.p. 22°, may be used. It may be prepared by using the procedure described under i o-propyl lactate (Section 111,102). Place a mixture of 75 g. of d-tartaric acid, 10 g. of Zeo-Karb 225/H, 110 g. (136 ml.) of redistilled n-butyl alcohol and 150 ml. of sodium-dried benzene in a 1-litre three-necked flask equipped with a mercury-sealed stirrer, a double surface condenser and an automatic water separator (see Fig. Ill, 126,1). Reflux the mixture with stirring for 10 hours about 21 ml. of water collect in the water separator. FUter off the ion-exchange resin at the pump and wash it with two 30-40 ml. portions of hot benzene. Wash the combined filtrate and washings with two 75 ml. portions of saturated sodium bicarbonate solution, followed by lOu ml. of water, and dry over anhydrous magnesium sulphate. Remove the benzene by distillation under reduced pressure (water pump) and finally distil the residue. Collect the di-n-butyl d-tartrate at 150°/1 5 mm. The yield is 90 g. 

Many solutions of common nonionic surfactants and water separate into two phases when heated above a certain temperature (the cloud point), and some investigators call the phase of greater surfactant concentration, a microemulsion. Thus, there is not even universal agreement that a microemulsion must contain oil. 

Fig. 6. Adsorption capacity of various dessicants vs years of service in dehydrating high pressure natural gas (39). a, Alumin a H-151, gas 27° C and 123 kPa, from oil and water separators b, siUca gel, gas 38° C and 145 kPa, from oil absorption plant c, sorbead, 136-kPa gas from absorption plant ...

In the United States, the Clean Air Act of 1970 imposed limitations on composition of new fuels, and as such methanol-containing fuels were required to obtain Environmental Protection Agency (EPA) waivers. Upon enactment of the Clean Air Act Amendments of 1977, EPA set for waiver unleaded fuels containing 2 wt % maximum oxygenates excluding methanol (0.3 vol % maximum). Questions regarding methanol s influence on emissions, water separation, and fuel system components were raised (80). 

When the recycle soot in the feedstock is too viscous to be pumped at temperatures below 93°C, the water—carbon slurry is first contacted with naphtha carbon—naphtha agglomerates are removed from the water slurry and mixed with additional naphtha. The resultant carbon—naphtha mixture is combined with the hot gasification feedstock which may be as viscous as deasphalter pitch. The feedstock carbon—naphtha mixture is heated and flashed, and then fed to a naphtha stripper where naphtha is recovered for recycle to the carbon—water separation step. The carbon remains dispersed in the hot feedstock leaving the bottom of the naphtha stripper column and is recycled to the gasification reactor. 

---