Mercury sealed stirrer

Alternatively a mercury-sealed stirrer may be employed. Here again a short glass tube C is inserted through the cork of the flask to act as a collar for the stirrer. The tube C carries a short wide tube B which is either fused at its lower end to C, or is fixed to it by means of a cork as shown. The stirrer D carries a precisely similar tube E, the top of which however is now fixed to D the bore of the tube E allows it to fit easily within the annular space between the collar C and the tube B. Mercury... 

A 1500 ml. flask is fitted (preferably by means of a three-necked adaptor) with a rubber-sleeved or mercury-sealed stirrer (Fig. 20, p. 39), a reflux water-condenser, and a dropping-funnel cf. Fig. 23(c), p. 45, in which only a two-necked adaptor is shown or Fig. 23(G)). The dried zinc powder (20 g.) is placed in the flask, and a solution of 28 ml. of ethyl bromoacetate and 32 ml. of benzaldehyde in 40 ml. of dry benzene containing 5 ml. of dry ether is placed in the dropping-funnel. Approximately 10 ml. of this solution is run on to the zinc powder, and the mixture allowed to remain unstirred until (usually within a few minutes) a vigorous reaction occurs. (If no reaction occurs, warm the mixture on the water-bath until the reaction starts.) The stirrer is now started, and the rest of the solution allowed to run in drop-wise over a period of about 30 minutes so that the initial reaction is steadily maintained. The flask is then heated on a water-bath for 30 minutes with continuous stirring, and is then cooled in an ice-water bath. The well-stirred product is then hydrolysed by the addition of 120 ml. of 10% sulphuric acid. The mixture is transferred to a separating-funnel, the lower aqueous layer discarded, and the upper benzene layer then... 

Fit a three necked 250 ml. flask with a central rubber-sleeved or mercury-sealed stirrer, c/. Fig. 23(c), p. 45, where only two necks are shown, and with a thermometer the bulb of which reaches as near the bottom of the flask as the stirrer allows the third neck will carry at first a dropping-funnel and later a reflux condenser. Place 20 g. (19-5 ml.) of ethyl acetoacetate and 45 ml. of glacial acetic acid in the flask and by ice-water cooling adjust the temperature of the stirred mixture to 5 -7° maintain this temperature whilst adding a solution of 5 4 g. of sodium nitrite in 8 ml. of water slowly from the dropping-funnel during 15 minutes. Continue the stirring for 20-30 minutes, and then... 

Mercury-sealed stirrers are used in the following operations (1) simultaneous stirring and refluxing of a reaction mixture (2) stirring the contents of a closed vessel (3) agitation with prevention of the escape of a gas or vapour and (4) stirring in an inert atmosphere, such as... 

The mercury-sealed stirrer is of the Hershberg type made of tantalum wire. 

In a dry 500 ml. three-necked fiask, equipped with a mercury-sealed stirrer, a 100 ml. dropping funnel and a short fractionating column (1), place a mixture of 116 g. of anhydrous, finely-powered potassium fluoride (2) and 200 g. of dry ethylene glycol (3). Connect the fractionating... 

Place a mixture of 53 g. of A.R. lactic acid (85-88 per cent, acid), 75 g. (85-5 ml.) of commercial anhydrous isopropyl alcohol, 300 ml. of benzene and 20 g. of Zeo-Karb 225/H (1) in a 700 ml. bolt-head flask, equipped with an automatic water separator (e.g., a large modified Dean and Stark apparatus with a stopcock at the lower end, see Fig. Ill, 126, 1) carrying an efficient reflux condenser at its upper end, and a mercury-sealed stirrer (alternatively, the hquid-sealed stirrer shown in Fig. 11,7,11, c. may be used). Reflux the mixture, with stirring, on a steam bath for 5 hours or until water no longer collects in appreciable amount in the water separator run off the water from time to time. Filter off the resin at the pump and wash it with two 25 ml. portions of benzene. Shake the combined filtrate and washings with about 5 g. of precipit-ated calcium... 

Allyl cyanide. Into a 1 5 litre three-necked flask (1), provided with a mercury-sealed stirrer and two long double surface condensers, place 293 g. (210 ml.) of freshly-distilled allyl bromide, b.p. 70-71° (Section III, 35) and 226 g. of dry cuprous cyanide (Section 11,50,3, Method 1), Remove the mercury-sealed stirrer and replace it by a tightly fitting... 

Into a 2-litre, three-necked flask, fitted with a separatory funnel, a mechanical stirrer and a reflux condenser, place a hot solution of 200 g. of potassium hydroxide in 200 ml. of water. Stir the solution and add slowly 200 g. of ethyl n-butylmalonate (Section 111,154). A vigorous reaction occurs and the solution refluxes. When all the ester has been added, boil the solution gently for 2-3 hours, i.e., until hydrolysis is complete a test portion should dissolve completely in water. Dilute with 200 ml. of water and distil oflF 200 ml. of liquid in order to ensure the complete removal of the alcohol formed in the hydrolysis (1) it is best to connect the flask by means of a wide delivery tube to a condenser set for downward distillation (compare Fig. II, 41, 1 but with a mercury-sealed stirrer in the centre neck). Replace the separatory funnel and the reflux condenser. 

Pelargonic acid (n-Nonoic acid), CH3(CH2),COOH. Equip a 1-litre, three-necked flask with a reflux condenser, a mercury-sealed stirrer, a dropping funnel and a thermometer. Place 23 g. of sodium, cut in small pieces, in the flask, and add 500 ml. of anhydrous n-butyl alcohol (1) in two or three portions follow the experimental details given in Section 111,152 for the preparation of a solution of sodium ethoxide. When the sodium has reacted completely, allow the solution to cool to 70-80° and add 160 g. (152 ml.) of redistilled ethyl malonate rapidly and with stirring. Heat the solution to 80-90°, and place 182 5 g. (160 ml.) of n-heptyl bromide (compare experimental details in Section 111,37) in the dropping funnel. Add the bromide slowly at first until precipitation of sodium bromide commences, and subsequently at such a rate that the n-butyl alcohol refluxes gently. Reflux the mixture until it is neutral to moist litmus (about 1 hour). 

Into a 1500 ml. three-necked flask, equipped with a dropping funnel, a mercury-sealed stirrer and a double surface condenser (the last-named provided at its upper end with a guard tube filled witla a mixture of... 

Method 1 (from nitrobenzene). Support a 1 htre three-necked flask, equipped with a mercury-sealed stirrer and a reflux condenser, on a water bath, and place a solution of 65 g. of sodium hydroxide in 150 ml. of... 

Support a 1500 ml. three-necked flask, equipped with a mercury-sealed stirrer and a double surface reflux condenser, on a water bath, and place a solution of 84 g. of sodium hydroxide in 185 ml. of water, 50 g. (41-5 ml.) of nitrobenzene and 500 ml. of methyl alcohol in the flask. Add 70 g. of zinc powder (1), start the stirrer, and reflux for 10 hours. The solution gradually assumes the reddish colour of azobenzene and then on further... 

Equip a 1 Utre three-necked flask or a 1 litre bolt- head flask with a reflux condenser and a mercury-sealed stirrer. Dissolve 50-5 g. of commercial 2 4-dinitro-l-chlorobenzene in 250 ml. of rectified spirit in the flask, add the hydrazine solution, and reflux the mixture with stirring for an hour. Most of the condensation product separates during the first 10 minutes. Cool, filter with suction, and wash with 50 ml. of warm (60°) rectified spirit to remove unchanged dinitrochlorobenzene, and then with 50 ml. of hot water. The resulting 2 4-dinitrophenylhydrazine (30 g.) melts at 191-192° (decomp.), and is pure enough for most purposes. Distil oflF half the alcohol from the filtrate and thus obtain a less pure second crop (about 12 g.) recrystallise this from n-butyl alcohol (30 ml. per gram). If pure 2 4-dinitrophenylhydrazine is required, recrystallise the total yield from n-butyl alcohol or from dioxan (10 ml. per gram) this melts at 200° (decomp.). 

The mercury-sealed stirrer may be replaced by a Kyrides stirrer (Fig. II, 7, 12) formed from a P.V.C. gland and lubricated with a mixture of vaseline and light paraffin. The continuous passage of nitrogen may be dispensed with if a fairly wide tube dipping into a little mercury is connected to the top of the condenser the latter serves to retain the nitrogen atmosphere. 

The purified commercial di-n-butyl d-tartrate, m.p. 22°, may be used. It may be prepared by using the procedure described under i o-propyl lactate (Section 111,102). Place a mixture of 75 g. of d-tartaric acid, 10 g. of Zeo-Karb 225/H, 110 g. (136 ml.) of redistilled n-butyl alcohol and 150 ml. of sodium-dried benzene in a 1-litre three-necked flask equipped with a mercury-sealed stirrer, a double surface condenser and an automatic water separator (see Fig. Ill, 126,1). Reflux the mixture with stirring for 10 hours about 21 ml. of water collect in the water separator. FUter off the ion-exchange resin at the pump and wash it with two 30-40 ml. portions of hot benzene. Wash the combined filtrate and washings with two 75 ml. portions of saturated sodium bicarbonate solution, followed by lOu ml. of water, and dry over anhydrous magnesium sulphate. Remove the benzene by distillation under reduced pressure (water pump) and finally distil the residue. Collect the di-n-butyl d-tartrate at 150°/1 5 mm. The yield is 90 g. 

---