Acrylonitrile-styrene copolymer AS

In a few instances, SAN is also addressed as acrylonitrile/styrene copolymer and abbreviated as AS. However, AS resins may actually target to acrylonitrile-butadiene-styrene resins. 

More recently, filled polyethers (so called polymer polyols ) have been introduced. These contain dispersed organic filler such as acrylonitrile-styrene copolymer or polyurea, some of which is grafted on to the polyether chain. Filled polyethers are used principally for flexible foams of high resilience. 

The term ABS was originally used as a general term to describe various blends and copolymers containing acrylonitrile, butadiene and styrene. Prominent among the earliest materials were physical blends of acrylonitrile-styrene copolymers (SAN) (which are glassy) and acrylonitrile-butadiene copolymers (which are rubbery). Such materials are now obsolete but are referred to briefly below, as Type 1 materials, since they do illustrate some basic principles. Today the term ABS usually refers to a product consisting of discrete cross-linked polybutadiene rubber particles that are grafted with SAN and embedded in a SAN matrix. 

The benzenoid C-l resonance of styrene units in acrylonitrile-styrene copolymers is particularly sensitive to the sequence of the chain relative configurations of triad sequences can be determined by quantitative evaluation of carbon-13 signals [524], Micro-structures of other vinyl polymers such as polystyrene [525], polypropylene oxide [526], and polyalkyl acrylates [527] have also been investigated by 13C NMR. 

Watanabe62) studied systematically the copolymerization of ra-methacryloyl-polyoxyethylenes, with monomers such as acrylonitrile, styrene, butyl methacrylate, and methacrylic acid. It should be mentioned that the macromonomers that he prepared are very short so that no difficulties were encountered to isolate the graft copolymers formed. There are many applications for these graft copolymers, e.g. as additives in polyacrylonitrile films and fibers they cause improved antistatic properties. They have been tested as varnishes, coatings, and wood dimensional stabilization agents. 

Acrylonitrile is used in the production of acrylic fibers, resins, and surface coating as an intermediate in the production of pharmaceuticals and dyes as a polymer modifier and as a fumigant. It may occur in fire-effluent gases because of pyroly-ses of polyacrylonitrile materials. Acrylonitrile was found to be released from the acrylonitrile-styrene copolymer and acrylonitrile-styrene-butadiene copolymer bottles when these bottles were filled wifh food-simulating solvents such as water, 4% acetic acid, 20% ethanol, and heptane and stored for 10 days to 5 months (Nakazawa et al. 1984). The release was greater with increasing temperature and was attributable to the residual acrylonitrile monomer in the polymeric materials. 

High density polyethylene (HDPE) Polycarbonate (PC) Polyvinyl chloride (PVC) Polystyrene (PS) Polyurethane (PUR) Polyurea + PUR Low density polyethylene ethyl + vinyl acetate (LDPE + EVA) Polyvinyl acetate (PVA) Acrylonitrile-styrene-butadiene (ABS) Acrylonitrile-styrene copolymer (AS) Styrene-butadiene-styrene (SBS) Polysiloxane Gelatin/arabic gum (G/AG)... 

Although the impact strength of acrylonitrile-styrene copolymers is higher than that of polystyrene, it is still sufficiently low to make it a limiting factor in many applications. Understandably, therefore, the addition of rubbery materials to acrylonitrile-styrene copolymers has been extensively investigated and as a result materials based on acrylonitrile, butadiene and styrene have become commercially available. Such materials are commonly referred to as ABS polymers. It should be noted that commercial ABS polymers are not random terpolymers of acrylonitrile, butadiene and styrene. 

The third process, stretch blow molding, utilizes biaxial orientation, which is possible with certain resins such as PET, PVC, polypropylene, and acrylonitrile-styrene copolymers. Because of the improved strength and stiffness, weight reduction is usually... 

A number of methods such as ultrasonics (137), radiation (138), and chemical techniques (139—141), including the use of polymer radicals, polymer ions, and organometaUic initiators, have been used to prepare acrylonitrile block copolymers (142). Block comonomers include styrene, methyl acrylate, methyl methacrylate, vinyl chloride, vinyl acetate, 4-vinylpyridine, acryUc acid, and -butyl isocyanate. 

Organic peroxides are used in the polymer industry as thermal sources of free radicals. They are used primarily to initiate the polymerisation and copolymerisation of vinyl and diene monomers, eg, ethylene, vinyl chloride, styrene, acryUc acid and esters, methacrylic acid and esters, vinyl acetate, acrylonitrile, and butadiene (see Initiators). They ate also used to cute or cross-link resins, eg, unsaturated polyester—styrene blends, thermoplastics such as polyethylene, elastomers such as ethylene—propylene copolymers and terpolymers and ethylene—vinyl acetate copolymer, and mbbets such as siUcone mbbet and styrene-butadiene mbbet. 

Styrene [100-42-5] (phenylethene, viaylben2ene, phenylethylene, styrol, cinnamene), CgH5CH=CH2, is the simplest and by far the most important member of a series of aromatic monomers. Also known commercially as styrene monomer (SM), styrene is produced in large quantities for polymerization. It is a versatile monomer extensively used for the manufacture of plastics, including crystalline polystyrene, mbber-modifted impact polystyrene, expandable polystyrene, acrylonitrile—butadiene—styrene copolymer (ABS), styrene—acrylonitrile resins (SAN), styrene—butadiene latex, styrene—butadiene mbber (qv) (SBR), and unsaturated polyester resins (see Acrylonithile polya rs Styrene plastics). 

Most of the surface sizes used in North America are modified styrene maleic anhydride (SMA) copolymers. Commercially available materials include Scripset (Monsanto/Hercules Inc.), Cypres (Cytec), Sursize (Akzo Nobel), MSA (Morton), NovaCote (Georgia Pacific), and HTl (Hopton Technologies). Styrene acrylate emulsions that are commonly used include Jetsize and Unibond (Akzo Nobel), Basoplast (BASF), and Cypres (Cytec). Other materials used as surface sizes include acrylonitrile acrylate copolymer (Basoplast, BASF), stearylated melamine resin (Sequapel, Sequa), polyurethane (Graphsize, Vining Chemicals), and diisobutylene maleic anhydride copolymers (Baysynthol, Bayer). 

---