Standards preparation sheet

To aid the analyst in providing necessary documentation, -forms were developed which prompted analysts to enter the needed information. One such form is illustrated in Figure 1. The top sections of the "Standards Preparation Sheet" shown in the figure direct the analyst to provide a wide range of information deemed essential for maintaining an adequate audit trail. In addition, the information in the upper right hand corner instructs the analyst on the proper distribution of the multiple copies of the form. 

Users should be the prime participants in the preparation process so that the resultant documents reflect their needs and are fit for the intended purpose - hence the requirement that documents be reviewed as well as approved. You will need to be able to demonstrate that your documents have in fact been reviewed prior to issue. The presence of a signature on the front cover is not sufficient evidence. To demonstrate that documents have been reviewed you will need to show that nominated personnel have been issued with drafts for comment and that they have provided comments which have been considered by the approval authorities. A simple method is to employ a standard comment sheet on which reviewers can indicate their comments or signify that they have no comment. During the review process you may undertake several revisions. You may feel it necessary to retain these in case of dispute later, but there is no compulsion for you to do so, providing you have evidence that the review took place. You also need to show that the current issue has been reviewed so your comment sheet needs to indicate document issue status. 

The items may also be classified differently in cost sheets and cost standards prepared to monitor the performance of the operating plant. For this purpose the fixed-cost items should be those over which the plant supervision has no control, and the variable items those for which they can be held accountable. 

ASTM D3182, 1989(2001 )e 1. Standard practice for rubber - Materials, equipment and procedures for mixing standard compounds and preparing standard vulcanized sheets. 

Chromatograph the sugar standards and the unknown(s) on the prepared sheets using the solvent systems detailed above. Calculate the Rf values of the standards and hence determine which of the standard components are in the unknown mixture(s). Account for the different R values in the two systems. 

Film and sheeting materials test methods have been standardized by ASTM, DIN, and others. As with all materials, the test specimens must be carefiiUy prepared and conditioned. Thin-film specimens are vulnerable to nicks and tears which mar the results. Moisture and temperature can affect some materials. Common test methods are Hsted in Table 1. 

TSR 5. Within the Malaysian scheme SMR 5 is restricted to mbber derived from sheet material prepared by conventional processes, ie, ribbed smoked sheet (RSS), air-dried sheet (ADS), and unsmoked sheet (USS) and presented in small bale form. Other countries may source different raw materials, eg, Indonesia produces SIR 5 from thin latex coagulum (14). SMR 5 prepared by pressing dry-sheet material into standard bales must be identified by the type of sheet material, eg, SMR 5RSS, on the test certificate as well as on the wrapping. 

Construction Codes Rules for Construction of Pressure Vessels, Division 1, which is part of Section T11 of the ASME Boiler and Pressure Vessel Code (American Society of Mechanical Engineers), sei ves as a construction code by providing minimum standards. New editions of the code are usually issued every 3 years. Interim revisions are made semiannually in the form of addenda. Compliance with ASME Code requirements is mandatoiy in much of the United States and Canada. Originally these rules were not prepared for heat exchangers. However, the welded joint between tube sheet and shell of the fixed-tube-sheet heat exchanger is now included. A nonmandatoi y... 

The required notification must be provided at ieast annually In writing. Acceptable forms of notice are, for example, a letter, product labeling, and product literature distributed to customers. If you are required to prepare and distribute a Material Safety Data Sheet (MSDS) for the mixture under the Occupational Safety and Health Act (OSHA) Hazard Communication Standard, your section 313 notification may be attached to the MSDS or the MSDS may be modified to include the required information. (A sample letter and recommended text for inclusion in an MSDS appear on pages E-4 and E-5 of this appendix.)... 

Hazard communication to users of dangerous chemical substances and preparations is accomplished by labelling and by means of safety data sheets (SDS), which give more detailed information to industrial users. An SDS has to be provided on request to the public for non-industrial preparations. There is a standard EU 16-heading format (Table 5) specified in the SDS Directive (a. 8). 

Another continuing project on aqueous nonelectrolytes is the International Data Series B. The editor is Dr. J. A. Larkin of the National Physical Laboratory in England. It is published in the form of supplements of loose-leaf sheets and issued at irregular intervals of a few months. Each sheet is prepared and submitted by an author or authors. The data are presented in a standard format and must follow certain rules with regard to kind of properties, style, units, and kind of auxiliary information to be included. Standard table formats have been designed for each kind of property included. Each table is reviewed by an editor specially selected from an international panel. 

Test samples have been prepared from a 3 mm hot-rolled steel sheet which showed an intact mill scale (Degree A of Swedish Standards, SIS-055900), Thereafter they were shot blasted with S-280 to reach the ASa3 standard, prior to the application of the paint coating. Surface preparation B St 2 was obtained by wire brushing a steel sheet of Grade B obtained in turn by oxidation of Grade A sheet in a contaminant free atmosphere. In "Table I.", the characteristics of the paints used in this study are shown. 

---