Spindle

Automated Magnetic Particle Testing of Truck Spindles. 

Resinoid-bonded wheels find wide use in heavy-duty snagging operations where large amounts of metal must be removed quickly, in cutting-off operations, portable disk grinding (as for weld-beads), roU grinding, and vertical spindle disk grinding. 

In false twist texturing (FTT), shown schematically in Figure 7, a device twists yam upstream of its location as the threadline passes across a heater, and the yam untwists downstream from the device and is wound up. If the yam is not heated downstream from the twist device, it has bulk and high elasticity (stretch). If the yam is heated downstream from the twist device, it has bulk, but much less stretch. FTT machines initially used two steps to sequentially draw and texture. Later machines combined those steps to simultaneously draw and texture (92). Initial machines used pin spindles as the false twist device. Texturing speeds were about 150 m/min and slowly increased to about 300 m/min. As POY quaUty and stmctural stabiUty improved, new... 

The mode of action has not yet been elucidated but the manufacturer states that it probably behaves like the herbicide triflurolin and its congeners. These materials inhibit cell division by binding to tubuHn thereby internipting micro-tubule development. This, in turn, stops spindle fiber formation essential to mitosis and cell division. Experiments with C-labeled Prime+ show that it is acutely toxic to fish with estimated LC q (96 h) of less than 100 ppb for rainbow trout and bluegiU. sunfish. However, channel catfish did not exhibit any toxic response at the maximum attainable water concentration (10). 

The Rockwed testing machine is thus a framework permitting stable support of the workpiece on one side and means to impress the indenter under specified load on the other. A dial indicator attached to the indenter spindle is used to read directly the depth of indentation in hardness numbers. 

The influences of herbicides on cell division fall into two classes, ie, dismption of the mitotic sequence and inhibition of mitotic entry from interphase (G, S, G2). If ceU-cycle analyses indicate increases in abnormal mitotic figures, combined with decreases in one or more of the normal mitotic stages, the effect is upon mitosis. Mitotic effects usually involve the microtubules of the spindle apparatus in the form of spindle depolymerization, blocked tubulin synthesis, or inhibited microtubule polymerization (163). Alkaloids such as colchicine [64-86-8J,viahla.stiae [865-21-4] and vincristine [57-22-7] dismpt microtubule function (164). Colchicine prevents microtubule formation and promotes disassembly of those already present. Vinblastine and vincristine also bind to free tubulin molecules, precipitating crystalline tubulin in the cytoplasm. The capacities of these dmgs to interfere with mitotic spindles, blocking cell division, makes them useful in cancer treatment. 

DCPA inhibits the growth of grass species by dismpting the mitotic sequence, probably at entry (190). DCPA influences spindle formation and function (181) and causes root-tip swelling (182) and britde shoot tissue (191). It has been reported that DCPA, like colchicine and vinblastine, attests mitosis at prometaphase and is associated with formation of polymorphic nuclei after mitotic arrest (192). Pronamide also inhibits root growth by dismpting the mitotic sequence in a manner similar to the effect of colchicine and the dinitroanilines (193,194). Cinmethylin and bensuhde prevent mitotic entry by unknown mechanisms (194). 

Because of the very small bearing clearances in gas bearings, dust particles, moisture, and wear debris (from starting and stopping) should be kept to a minimum. Gas bearings have been used in precision spindles, gyroscopes, motor and turbine-driven circulators, compressors, fans, Brayton cycle turbomachinery, environmental simulation tables, and memory dmms. 

Slurry Viscosity. Viscosities of magnesium hydroxide slurries are determined by the Brookfield Viscometer in which viscosity is measured using various combinations of spindles and spindle speeds, or other common methods of viscometry. Viscosity decreases with increasing rate of shear. Fluids, such as magnesium hydroxide slurry, that exhibit this type of rheological behavior are termed pseudoplastic. The viscosities obtained can be correlated with product or process parameters. Details of viscosity deterrnination for slurries are well covered in the Hterature (85,86). 

Power consumption during metal cutting can be estimated from forces acting on a tool during the cutting. This can be measured on a dynamometer. In cutting operations the power consumption, P, at the spindle, in watts, is approximately equal to... 

With several springs, which function as torque gauges, and a number of spindles, viscosities can be measured up to 10 mPa-s with the Brookfield viscometer. The shear rates depend on the model and the sensor system they are ca 0.1 100 for the disk spindles, <132 for concentric cylinders, and <1500 for the cone—plate forlow viscosity samples. Viscosities at very low (ca 10 — 1 )) shear rates can be measured with the concentric... 

The Nametre Rotary B rotational viscometer measures torque in terms of the current needed to drive the d-c motor at a given speed while a material is under test. The standard sensors are coaxial cylinders or Brookfield disk-type spindles, but a cone—plate system is also available. The viscosity range for the coaxial cylinder sensors is 5 to 5 x 1(T mPa-s, and the maximum shear rate is 200. ... 

Density. Measurement of density is widely used in the sugar industry to determine the sugar concentration of symps, Hquors, juices, and molasses. The instmment used is called a hydrometer or a spindle. When it is graduated in sucrose concentration (percent sucrose by weight), it is called a Brix hydrometer or a Brix spindle. Brix is defined as the percent of dry substance by hydrometry, using an instmment or table caUbrated in terms of percent sucrose by weight in water solution. Hydrometers are also graduated in °BaumH, stiU in use in some industries. The relationship between °BaumH and density, ing/cm, is °Baumn Baum e = 145(1 — 1/d). 

Although spindles are caUbrated for pure sucrose, other components are normally present in sugar that contribute to the density, such as ash and invert. Because the densities of these components are not much different from that of sucrose, the spindle value is considered a measure of total dissolved substances. 

Once the plant is ready, the cotton is mechanically harvested with either a spindle picker or cotton stripper. The spindle picker selectively harvests seed cotton from open boUs. The unopened boUs are left on the plant and can be picked at a later date. The spindle picker uses a rotating tapered barbed spindle to remove the cotton from the bur (seed case). The seed cotton is wrapped around the spindle, pulled from the bur, removed from the spindle with a mbber doffer, and then transferred to a basket. 

---