System sensor

To realize a process integrated quality control the conception shown in fig. 2 was followed. The casting process which is influenced by process parameters like thermal economy, alloy composition or black wash will be pursued with particulary to the problematic nature adjusted sensoring systems. On basic factors orientated sensoring systems like microfocus radioscopy, and tomography will be employed and correlated with sensoring systems which can be applicated under industrial conditions. 

The contribution that Hocking wished to make was to refine the sensor system and the instrumentation paekage so as to be able to incorporate the necessary functionality within a lightweight portable battery operated instrument. This implied a lower power level and very low-noise instrumentation. We aimed also for a low cost instrument able to operate for several hours from fully charged batteries and able to operate at a pull speed of 500mm/second. 

Selected sensor systems are moved over long cracks of different widths. The output signals are pre-calculated by using eq.(6). Measured and pre-calculated data are compared in 4.2.3.. 

Figure 6 Measured output signals of different sensor systems...

Fig. 6 shows the output signals of the three different sensor systems described in chapter 3. The pot-core coil from chapter 4.2.1. is used for the measurement of the inductance with the... 

So, a comparison of different types of magnetic field sensors is possible by using the impulse response function. High amplitude and small width of this bell-formed function represent a high local resolution and a high signal-to-noise-characteristic of a sensor system. On the other hand the impulse response can be used for calculation of an unknown output. In a next step it will be shown a solution of an inverse eddy-current testing problem. 

Due to its importance the impulse-pulse response function could be named. .contrast function". A similar function called Green s function is well known from the linear boundary value problems. The signal theory, applied for LLI-systems, gives a strong possibility for the comparison of different magnet field sensor systems and for solutions of inverse 2D- and 3D-eddy-current problems. 

With several springs, which function as torque gauges, and a number of spindles, viscosities can be measured up to 10 mPa-s with the Brookfield viscometer. The shear rates depend on the model and the sensor system they are ca 0.1 100 for the disk spindles, <132 for concentric cylinders, and <1500 for the cone—plate forlow viscosity samples. Viscosities at very low (ca 10 — 1 )) shear rates can be measured with the concentric... 

Many physical principles can be employed by different sensor vendors to obtain the same measurement. For example, in 1995, 49 vendors were listed for hydrogen sensing (2). Represented among the sensor systems are mass spectrometers, gas chromatographs, electrochemical cells, thermal... 

An important part of the decision-making tool flow chart (see Fig. 1) is the redefinition of the specifications by the sensor customer after the surveying and testing of commercial sensor systems. This process almost always involves a downgrading of the expectations of the sensor customer, but it can also force a reaUstic evaluation of what sensor information really needs to be made available and at what cost. 

One system for measuring catalyst failure is based on two oxygen sensors, one located in the normal control location, the other downstream of the catalyst (102,103). The second O2 sensor indicates relative catalyst performance by measuring the abiUty to respond to a change in air/fuel mixture. Other techniques using temperatures sensors have also been described (104—107). Whereas the dual O2 sensor method is likely to be used initially, a criticism of the two O2 sensors system has been reported (44) showing that properly functioning catalysts would be detected as a failure by the method. 

Thus vanadium oxide (IV) eould be of interest for sensor systems. 

This work is financially supported by Programme of Eundamental Researches of the National Academy of Sciences of Ukraine Investigations in the field of sensor systems and technologies (grant No. 3-13/SD-2005). 

Methods of analysis based on the use of different sensor systems -eleetroehemieal, optie, fluorimetrie, instmmental and visual - mostly meet sueh requirements. 

In this work the results of seai eh of sensor systems suitable for analysis of liquid and solid media for eontent of volatile aliphatie amines ai e presented. The most suitable proeedure of analysis is gas extraetion - deteetion . 

The work was supported by INTAS grant Open Call 03-51-6278, NATO Linkage grant LST.NUKR.CLG 980621 and the grants of the Program Sensor Systems and Technologies funded by NAS of Ukraine. 

Campbell, M. (ed.J (1996) Sensor System for Environmental Monitoring, Kluwer Academic Publishers, The Hague. Carson, P.A., and Dent, N.J. (ed.) (1990) Good Laboratory and Clinical Practices, Hememann Newnes, Oxford. Carson, P.A., and Mumford, C.J. (1988) The Safe Handling of Chemicals in Industry (Vols 1 and 2), Longman Scientific and Technical, Harlow. 

Possible applications of MIP membranes are in the field of sensor systems and separation technology. With respect to MIP membrane-based sensors, selective ligand binding to the membrane or selective permeation through the membrane can be used for the generation of a specific signal. Practical chiral separation by MIP membranes still faces reproducibility problems in the preparation methods, as well as mass transfer limitations inside the membrane. To overcome mass transfer limitations, MIP nanoparticles embedded in liquid membranes could be an alternative approach to develop chiral membrane separation by molecular imprinting [44]. 

For example, Novasina S.A. (www.novasina.com), a Swiss company specializing in the manufacture of devices to measure humidity in air, has developed a new sensor based on the non-synthetic application of an ionic liquid. The new concept makes simple use of the close correlation between the water uptake of an ionic liquid and its conductivity increase. In comparison with existing sensors based on polymer membranes, the new type of ionic liquid sensor shows significantly faster response times (up to a factor of 2.5) and less sensitivity to cross contamination (with alcohols, for example). Each sensor device contains about 50 pi of ionic liquid, and the new sensor system became available as a commercial product in 2002. Figure 9-1 shows a picture of the sensor device containing the ionic liquid, and Figure 9-2 displays the whole humidity analyzer as commercialized by Novasina S.A.. 

Short Term Noise consists of base line perturbations that have a frequency that is significantly higher than the eluted peak. Short term detector noise is not often a serious problem m liquid chromatography as it can be easily removed by an appropriate noise filter without affecting the profiles of the peaks. Its source is usually electronic, originating from either the detector sensor system or the amplifier. 

The whole NMR imaging sensor system usually consists of a magnet, a shim system mounted inside the room-temperature bore of the magnet, a gradient system mounted inside the shim system and the rf coil mounted inside the gradient system. In the case of a saddle coil or a birdcage resonator, open access can be realized from the bottom to the top of the entire system with the coil diameter. 

K. L. McCarthy, Y. Lee, J. Green, M. J. McCarthy 2002, (Magnetic resonance imaging as a sensor system for multiphase mixing), Appl. Mag. Reson. 22, 213. 

Operational schematic of discontinuous biosensing system (assay), 16 3-3 Key characteristics of sensor systems, 17... 

National Research Council, Sensor Systems for Biological Agent Attacks Protecting Buildings and Military Bases, Washington, D.C. The National Academies Press, 2005. 

---