Pump seal

Control Room. The control room location can be critical to the efficient operation of a faciHty. One prime concern is to locate it the maximum distance from the most ha2ardous units. These units are usually the units where LPG or other flammables, eg, hydrocarbons that are heavier than air, can be released and accumulate at grade level. Deadly explosions can occur if a pump seal on a light-ends system fails and the heavier-than-air hydrocarbons coUect and are ignited by a flammable source. Also, the sulfur recovery unit area should be kept at a healthy distance away as an upset can cause deadly fumes to accumulate. 

Condensate Polishing. Ion exchange can be used to purify or poHsh returned condensate, removing corrosion products that could cause harmful deposits in boilers. Typically, the contaminants in the condensate system are particulate iron and copper. Low levels of other contaminants may enter the system through condenser and pump seal leaks or carryover of boiler water into the steam. Condensate poHshers filter out the particulates and remove soluble contaminants by ion exchange. 

Applications The common Heliflow apphcations are tank-vent condensers, sample coolers, pump-seal coolers, and steam-jet vacuum condensers. Instant water heaters, glycoLwater seivdces, and cryogenic vaporizers use the spiral tube s ability to reduce thermally induced stresses caused in these apphcations. 

Some toll processes lend themselves to test runs in the pre-startup phase. Actual materials for the toll may be used in the test or substitute materials, typically with low hazard potential, are often used to simulate the charging, reaction, and physical changes to be accomplished in the toll. Flow control, temperature control, pressure control, mixing and transferring efficiency can be measured. Mechanical integrity can be verified in regard to pumps, seals, vessels, heat exchangers, and safety devices. 

Does your house have air conditioning, or a heat pump Do you have solar he,- ig, a Jacu22i bath, swimming pool, aquarium, solar heating, a roof mounted water storage tank, a well, a power assisted commode, a motorboat, a jet ski, ATV or camper Then you have even more mechanical sealed pumps. We have mechanical sealed pumps in practically all facets of our everyday life, and these pump seals last for years wii problems. 

Report the total of all releases to the air that are not released through stacks, vents, ducts, pipes, or any other confined air stream. You must include (1) fugitive equipment leaks from valves, pump seals, flanges, compressors, sampling connections, open-ended lines, etc. (2) evaporative losses from surface impoundments and spills (3) releases from building ventilation systems and (4) any other fugitive or non-point air emissions. 

A vacuum pump seal drum design which provides a liquid seal (hydraulic flame arrester) to mitigate flame propagation backward into the vacuum system. The seal liquid is an organic stream (mostly Cg aromatics) that comes from the vacuum pump discharge drum overflow. 

In an offshore oil production platform, a major accident occurred partly because pump seals failed and therefore an antifoaming agent was not delivered to a crude oil separator. The fact that the pump seals were defective should have been picked up during routine inspections, but the inspections were neglected because of production pressures. The failure to carry out the inspections was a latent error. 

The change management process should also ensure that a root cause analysis has been conducted to make sure the real problem has been identified and corrected. For example, if a pump seal fails it could simply be replaced with an identical seal. However, it may have failed because it was left in service beyond its natural life and the real failure was in the preventative maintenance program that should have replaced it earlier. 

The final element of the equipment description is the equipment boundary figure. A boundary figure is included with each data cell to define the components and limits of the equipment associated with that cell. For example, the data cell boundary figure (Data cell 3.3.7.2.1.1) in Figure 3.2 shows that the centrifugal pump, seal system, motor, motor control unit, lube oil system, coupling, and transmission are all components of the equipment in the data cell. The equipment boundary is inherently reflected in the taxonomy number. 

Many data cells in the CCPS Taxonomy use equipment boundaries found in available generic data sets in which equipment and service is similar to that in the CPI. The boundaries established for other data cells were generally combinations of normal equipment modules—such as pump, seals, coupling, motor and base plate, or refrigeration units—and functionally interdependent basic and auxiliary components, such as motor controllers. Boundaries may change as greater amounts of equipment reliability data become available. 

ATWS A Reappraisal, Part 3 Frequency of Unanticipated Transients Nuclear 200 pump failure events from Arkansas Nuclear Unit 1, Calvert Cliff Unit 1, and Indian Point Unit 3 nuclear plants Nuclear reactor coolant pump seals 102. 

DATA BOUNDARY Nuclear reactor coolant pump seals... 

There is usually an ionic strength above which there is no more effect on hydrodynamic size or, worse yet, there are hydrophobic interactions of the polymer with the stationary phase. Thus, the optimum 1 is usually at the low 1 end of the plateau of size vs 1. This concentration will minimize ionic strength effects while also minimizing wear on the pump seals and pistons. 

GPSLLK Glycol pump seal leaks undetected... 

Water pump seals, hoses for air-conditioning systems, seals in cooling systems and covers in diesel injection systems... 

McNally, L. Increase Pump Seal Life, Hydro. Proc. V. 58, No. 1, 1979. Lapp, S., Hotv to Avoid Problems with Cold Service Pumps, Hydro. Proc., V. 60, No, 1, 1981,... 

Figure 6-36. Typical capacity increases gained when a vacuum pump sealed with relatively cool water handles air saturated with water vapor. By permission, Nash Engineering Co.

The thermal-convection loops are limited to flow velocities up to about 6 cm s . Where higher velocities are required, the liquid must be pumped, either mechanically or electromagnetically the latter is usually preferred as it avoids the problem of leakage at the pump seal. Basically, these forced-convection systemsconsist of (c) a hot leg, where the liquid metal is... 

INNER SEAL X OUTER SEAL PUMP SEAL HOUSING... 

---