Cell Data

Chains, intra- and intermolecular OH -- OH bonds Unknown, only unit cell data available 292 293... 

These experiments were carried out with the copper deposition reaction, which creates a large density difference at high concentrations. The diffus-ivity data used were the diaphragm cell data of Cole and Gordon (C12a). These data, as correlated by Fenech (F3), were also used in later work on horizontal electrodes. The question whether molecular diffusivity data are adequate for the work in question, has been discussed in Section IV,C.5... 

The comparative 2016 coin cell data of the uncoated vs. Si-coated spheroidized natural graphite precursor vs Li metal counter electrode (Figure 5) reveals a remarkable effect of metal addition onto the reversible capacity of anode. Thus, the starting material s reversible capacity increased from approximately 350 mAh/g to over 510 mAh/g (data taken at 0.8V vs Li/Li+), which is 1.37 times higher than the theoretical value of the reversible capacity for graphite. 

French500 has collected together unit-cell data for maltose hydrate and some poly-O-acylsaccharides in the hope that some packing information might be obtained which could be applied to the problem of starch structure. 

The orthogonal projection of the epitaxial poly(DMDA) could not be indexed using the unit cell data for the bulk polymerized crystal (8). However, poly(DMDA) cannot usually be polymerized to completion or to high crystallinity in the bulk due to cross-linking. The use of an epitaxial substrate may have controlled the polymerization process that led to oriented single crystals. 

Amidon and Houghton [48] completed a comparative study of several common methods of characterizing powder flow. Table 2 contains experimental results for a number of commonly used pharmaceutical excipients. Compressibility index, angle of repose, flow rate through an orifice, and shear cell data are presented. 

Shear cell measurements offer several pieces of information that permit a better understanding of the material flow characteristics. Two parameters, the shear index, n, and the tensile strength, S, determined by fitting simplified shear cell data to Eq. (6), are reported in Table 2. Because of the experimental method, only a poor estimate of the tensile strength is obtained in many cases. The shear index estimate, however, is quite reliable based on the standard error of the estimate shown in parenthesis in Table 2. The shear index is a simple measure of the flowability of a material and is used here for comparison purposes because it is reasonably reliable [50] and easy to determine. The effective angle of internal... 

Table 6 shows the usefulness of shear cell data in formulation development. Variations in relative humidity can profoundly influence flow this is a valuable piece of information for formulation development. Shear cell methodology thus provides useful data for optimizing the flow of formulations as well. 

A conductivity cell is set up using an yttria-stabilized zirconia electrolyte. At 900°C the equilibrium pressure in the cell was 1.02 x 10-10 atm, and the reference pressure outside the cell was 7.94 x 10 18 atm. (a) What is the cell voltage The temperature was dropped to 800°C and the reference pressure changed to 1.61 x 10-19 atm. The measured equilibrium voltage was 946 mV. (b) What is the equilibrium oxygen pressure in the cell [Data adapted from D-K. Lee et al., J. Solid State Chem., 178, 185-193 (2005).]... 

Adding Value to Kinetic Testing Data I - Interpretation of Tailings Humidity Cell Data from the Perspectives of Aqueous Geochemistry and Mineralogy at the Crowflight Minerals, Bucko Lake Nickel Project... 

A spike event was used to determine the retention time of the cells. Data from the spike event, flow rate, and changes in metal concentrations in cells were considered, allowing calculation of retention time. Percentages were used as a normalizing function for data analysis. 

Adding value to Kinetic Testing Data II - Interpretation of waste rock humidity cell data from an exploration perspective at the Adanac Molybdenum Corporation, Ruby Creek Molybdenum Project, BC,... 

Table 1. Humidity cell data (mg/L) showing variation between periods of sulfide... 

By using open or vented cells, data are obtained to determine if the full-scale reactor vent flow will be single or two-phase, and if a tempered or nontempered reaction occurs [192]. A tempered reaction is one that can be controlled through the latent enthalpy of evaporation. 

TABLE 24. Effect of Sodium Acetate Electrolyte on Ammonia Volatility at 80°C from Flow Cell Data... 

Table 7.3. Unit cell data of the hR6-As type elements.

Figure 3-8 Single Cell Direct Methanol Fuel Cell Data (45)...

Fig. 7.16 (a) Lattice parameters and (b) voltage vs x for two forms of Li TiSj. The c parameter for the layered (IT) form is the distance between the layers the a parameter in the cubic (spinel) form is the edge of the cubic unit cell. Data from Sinha and Murphy (1986), Dahn and McKinnon (1984), and Dahn and Haering (1981b). 

A number of other drugs (shown in Table 1.2) have been reported to inhibit 5-LO activity. In many cases, only whole cell data supports this mechanism of action other mechanisms may also be responsible for the cellular effects seen. A discussion of these compounds is beyond the scope of this review some leading references are summarized in Table 1.2. 

Fig. 7. Effects of vinblastine, vindesine, vincristine, vinzolidine, and vinepidine on neuronal processes in cultured rat midbrain cells [data from Boder et at. (9i)).

---