Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Stress-induced

Due to the absorbed photon energy in the moment of the beam admission the particles and the substrate surface warm up very fast. As a consquence of the thermal induced stresses between the relative brittle hard particles, some particles brake apart and, because of the released impulse energy, they are ejected out of the effective beam zone, transmission... [Pg.547]

Fabrication Expanding the tube into the tube sheet reduces the tube wall thickness and work-hardens the metal. The induced stresses can lead to stress corrosion. Differential expansion between tubes and shell in fixed-tube-sheet exchangers can develop stresses, which lead to stress corrosion. [Pg.1074]

Applications The common Heliflow apphcations are tank-vent condensers, sample coolers, pump-seal coolers, and steam-jet vacuum condensers. Instant water heaters, glycoLwater seivdces, and cryogenic vaporizers use the spiral tube s ability to reduce thermally induced stresses caused in these apphcations. [Pg.1086]

The method makes use of the principle that a constant ratio of induced stress. s in the stored contents to the consolidating pressure p exists. Thus, for any hopper design for which th.eff curve is available, the shear-tester results can be potted, and the point where/= s is located. Since the distance at which this occurs above the hopper vertex is also known, these values become the hopper dimensions at that point. [Pg.1938]

Surface defects, if sufficiently severe, may result in failure by themselves. More commonly, they act as triggering mechanisms for other failure modes. For example, open laps or seams may lead to crevice corrosion or to concentration sites for ions that may induce stress-corrosion cracking. [Pg.316]

Fig. 28.13. A sharp change of section induces stress concentrations. The local stress can be many times greater than the nominal stress. Fig. 28.13. A sharp change of section induces stress concentrations. The local stress can be many times greater than the nominal stress.
In contrast to pipelines and harbor installations, platforms are dynamically loaded. Therefore in the choice of steels, in addition to strength and types of machinability, the risk of corrosion fatigue and strain-induced stress corrosion must be taken into account in combination with cathodic protection (see Sections 2.3.3 to 2.3.5). [Pg.367]

The protection potentials for seawater are described in Section 2.4. In pipelines and harbor installations, there is no limiting negative potential t/ for uncoated earbon steel or for steel provided with thiek eoatings over 1 mm, with yield points up to 800 N mm". With dynamieally highly loaded structures, the protection potential ranges in Table 16-2 should be adhered to as in the regulations [1-3] because of the risk of hydrogen-induced stress corrosion (see Section 2.3.4). [Pg.368]

Cathodic protection cannot work with prestressed concrete structures that have electrically insulated, coated pipes. There is positive experience in the case of a direct connection without coated pipes this is protection of buried prestressed concrete pipelines by zinc anodes [38], Stability against H-induced stress corrosion in high-strength steels with impressed current has to be tested (see Section 2.3.4). [Pg.428]

Graphite will creep imder neutron irradiation and stress at temperatures where thermal creep is normally negligible. The phenomenon of irradiation creep has been widely studied because of its significance to the operation of graphite moderated fission reactors. Indeed, if irradiation induced stresses in graphite moderators could not relax via radiation creep, rapid core disintegration would result. The observed creep strain has traditionally been separated into a primary reversible component ( ,) and a secondary irreversible component (Ej), both proportional to stress and to the appropriate unirradiated elastic compliance (inverse modulus) [69]. The total irradiation-induced creep strain (ej is thus ... [Pg.468]

L Low <5 mpy, for all concentrations and temperatures 50 mpy see Induces stress corrosion cracking... [Pg.56]

As indicated, an implicit assumption of the JKR theory is that there are no interactions outside the contact radius. More specifically, the energy arguments used in the development of the JKR theory do not allow specific locations of the adhesion forces to be determined except that they must be associated with the contact line where the two surfaces of the particle and substrate become joined. Adhesion-induced stresses act at the surface and not a result of action-at-a-distance interatomic forces. This results in a stress singularity at the circumference of the contact radius [41]. The validity of this assumption was first questioned by Derjaguin et al. [42], who proposed an alternative model of adhesion (commonly referred to as the DMT theory ). Needless to say, the predictions of the JKR and DMT models are vastly different, as discussed by Tabor [41]. [Pg.151]

Up to this point, the discussion has been limited to cases where the adhesion-induced stresses result in elastic deformation. However, as previously discussed, this need not be the case. Indeed, these stresses can be, in many instances, comparable to the Young s moduli of the contacting materials, often resulting in plastic deformations. This area has been most notably explored by Maugis and Pollock [63]. [Pg.158]

According to the theory proposed by Maugis and Pollock, hereafter referred to as the MP model, if the adhesion induced stresses cause at least one of the contacting materials to yield and undergo a totally plastic response, the contact region formed will increase in size until the force causing the yielding is balanced... [Pg.158]

Another example of time-dependent adhesion has been reported by Rimai et al. [110], In this study, adhesion-induced stresses were found to cause an alternating block polyester/PDMS copolymer was found to flow over stacks of particles during a 2-week-long interval, suggestive of the occurrence of viscoelastic flow. [Pg.180]

As of this time, no one has solved the problem of the effect of asperities on a curved surface nor has anyone addressed the issue of crystalline facets. Needless to say, the problem of asperities on an irregular surface has not been addressed. However, Fuller and Tabor [118] have proposed a model that addresses the effects of variations of asperity size on adhesion for the case of planar surfaces. Assuming elastic response to the adhesion-induced stresses, they treated surface roughness as a random series of asperities having a Gaussian height distribution (f> z) and standard deviation o. Accordingly,... [Pg.184]

Fig. 7. Schematic representation of hydration causing crack propagation in a wedge test specimen. The increase in volume upon hydration induces stresses at the crack tip that promote crack growth 19,391. Fig. 7. Schematic representation of hydration causing crack propagation in a wedge test specimen. The increase in volume upon hydration induces stresses at the crack tip that promote crack growth 19,391.
If these changes in length take place freely then we will have a thermally induced strain in the material (= 0.3 x 100/50 = 0.6% in the polypropylene) but no stress. However, if the polypropylene was constrained in some way so that the 0.3 mm expansion could not happen when it is heated by 60°C, then there would be a thermally induced stress in the material, i.e. [Pg.62]

This example illustrates the simplified approach to film blowing. Unfortunately in practice the situation is more complex in that the film thickness is influenced by draw-down, relaxation of induced stresses/strains and melt flow phenomena such as die swell. In fact the situation is similar to that described for blow moulding (see below) and the type of analysis outlined in that section could be used to allow for the effects of die swell. However, since the most practical problems in film blowing require iterative type solutions involving melt flow characteristics, volume flow rates, swell ratios, etc the study of these is delayed until Chapter 5 where a more rigorous approach to polymer flow has been adopted. [Pg.268]

Duplex stainless steels are mostly composed of alternate austenite and ferrite grains. Their structure improves resistance to chloride-induced stress corrosion cracking. In certain reducing acids, such as acetic and formic, preferential attack of the ferrite is a serious problem. [Pg.906]

Nickel-chromium alloys can be used in place of austenitic stainless steels where additional corrosion resistance is required. These alloys are still austenitic but are highly resistant to chloride-induced stress corrosion cracking when their nickel content exceeds 40 per cent. [Pg.906]

Molten alkali hydroxides are particularly dangerous, not only because of scale fluxing, but also because they induce stress corrosion where stress is a serious factor. [Pg.1036]

Titanium is immune to chloride induced stress-corrosion cracking but more expensive than type 300 series stainless steels. [Pg.21]

Little information is available on the performance of copper and of copper alloys in contact with concrete, but concrete sometimes contains ammonia, even traces of which will induce stress-corrosion cracking of copper pipe. The ammonia may be derived from nitrogenous foaming agents used for producing lightweight insulating concrete. [Pg.53]


See other pages where Stress-induced is mentioned: [Pg.531]    [Pg.13]    [Pg.83]    [Pg.500]    [Pg.522]    [Pg.215]    [Pg.64]    [Pg.67]    [Pg.67]    [Pg.69]    [Pg.163]    [Pg.402]    [Pg.76]    [Pg.149]    [Pg.1016]    [Pg.15]    [Pg.250]    [Pg.306]    [Pg.902]    [Pg.903]    [Pg.905]    [Pg.213]    [Pg.144]    [Pg.1193]    [Pg.1209]    [Pg.20]    [Pg.36]   
See also in sourсe #XX -- [ Pg.236 ]




SEARCH



© 2024 chempedia.info