Polymer styrene-butadiene copolymers

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

One method (116) of producing cellular polymers from a variety of latexes uses primarily latexes of carboxylated styrene—butadiene copolymers, although other elastomers such as acryUc elastomers, nitrile mbber, and vinyl polymers can be employed. 

The most common VI improvers are methacrylate polymers and copolymers, acrylate polymers (see Acrylic ester polymers), olefin polymers and copolymers, and styrene—butadiene copolymers. The degree of VI improvement from these materials is a function of the molecular weight distribution of the polymer. VI improvers are used in engine oils, automatic transmission fluids, multipurpose tractor fluids, hydrautic fluids, and gear lubricants. Their use permits the formulation of products that provide satisfactory lubrication over a much wider temperature range than is possible using mineral oils alone. 

G-5—G-9 Aromatic Modified Aliphatic Petroleum Resins. Compatibihty with base polymers is an essential aspect of hydrocarbon resins in whatever appHcation they are used. As an example, piperylene—2-methyl-2-butene based resins are substantially inadequate in enhancing the tack of 1,3-butadiene—styrene based random and block copolymers in pressure sensitive adhesive appHcations. The copolymerization of a-methylstyrene with piperylenes effectively enhances the tack properties of styrene—butadiene copolymers and styrene—isoprene copolymers in adhesive appHcations (40,41). Introduction of aromaticity into hydrocarbon resins serves to increase the solubiHty parameter of resins, resulting in improved compatibiHty with base polymers. However, the nature of the aromatic monomer also serves as a handle for molecular weight and softening point control. 

Elastomers. Elastomers are polymers or copolymers of hydrocarbons (see Elastomers, synthetic Rubber, natural). Natural mbber is essentially polyisoprene, whereas the most common synthetic mbber is a styrene—butadiene copolymer. Moreover, nearly all synthetic mbber is reinforced with carbon black, itself produced by partial oxidation of heavy hydrocarbons. Table 10 gives U.S. elastomer production for 1991. The two most important elastomers, styrene—butadiene mbber (qv) and polybutadiene mbber, are used primarily in automobile tires. 

Almost all synthetic binders are prepared by an emulsion polymerization process and are suppHed as latexes which consist of 48—52 wt % polymer dispersed in water (101). The largest-volume binder is styrene—butadiene copolymer [9003-55-8] (SBR) latex. Most SBRlatexes are carboxylated, ie, they contain copolymerized acidic monomers. Other latex binders are based on poly(vinyl acetate) [9003-20-7] and on polymers of acrylate esters. Poly(vinyl alcohol) is a water-soluble, synthetic biader which is prepared by the hydrolysis of poly(viayl acetate) (see Latex technology Vinyl polymers). 

Between the 1920s when the initial commercial development of mbbery elastomers based on 1,3-dienes began (5—7), and 1955 when transition metal catalysts were fkst used to prepare synthetic polyisoprene, researchers in the U.S. and Europe developed emulsion polybutadiene and styrene—butadiene copolymers as substitutes for natural mbber. However, the tire properties of these polymers were inferior to natural mbber compounds. In seeking to improve the synthetic material properties, research was conducted in many laboratories worldwide, especially in the U.S. under the Rubber Reserve Program. 

The common feature of these materials was that all contained a high proportion of acrylonitrile or methacrylonitrile. The Vistron product, Barex 210, for example was said to be produced by radical graft copolymerisation of 73-77 parts acrylonitrile and 23-27 parts by weight of methyl acrylate in the presence of a 8-10 parts of a butadiene-acrylonitrile rubber (Nitrile rubber). The Du Pont product NR-16 was prepared by graft polymerisation of styrene and acrylonitrile in the presence of styrene-butadiene copolymer. The Monsanto polymer Lopac was a copolymer of 28-34 parts styrene and 66-72 parts of a second monomer variously reported as acrylonitrile and methacrylonitrile. This polymer contained no rubbery component. 

The low temperature ene reactions of 4-substituted-l,2,4-triazoline-3,5-diones (RTD) were used to modify polydiene surfaces. Hydrophilic surfaces (contact angles with water of 30-50°) were obtained on polybutadiene, poly-isoprene and styrene-butadiene copolymers by first treating the polymer at room temperature with RTD (R=Ph,... 

Polymer Preparation. A more recent modification in the molecular structure of styrene-butadiene copolymers has been obtained with the discovery of a new catalyst system (6). The catalyst consists of a barium t-alkoxide-hydroxide salt together with a complex of dialkylmagnesium and trialkylaluminum. 

Polymeric particles can be constructed from a number of different monomers or copolymer combinations. Some of the more common ones include polystyrene (traditional latex particles), poly(styrene/divinylbenzene) copolymers, poly(styrene/acrylate) copolymers, polymethylmethacrylate (PMMA), poly(hydroxyethyl methacrylate) (pHEMA), poly(vinyltoluene), poly(styrene/butadiene) copolymers, and poly(styrene/vinyltoluene) copolymers. In addition, by mixing into the polymerization reaction combinations of functional monomers, one can create reactive or functional groups on the particle surface for subsequent coupling to affinity ligands. One example of this is a poly(styrene/acrylate) copolymer particle, which creates carboxylate groups within the polymer structure, the number of which is dependent on the ratio of monomers used in the polymerization process. 

A specific example is used to illustrate the MLR methods, as well as the other quantitative calibration methods discussed in this section. In this example, a total of 70 different styrene-butadiene copolymers were analyzed by NIR transmission spectroscopy.39 For each of these samples, four different properties of interest were measured the concentrations of czs-butadiene units, trans-butadiene units, 1,2-butadiene units, and styrene units in the polymer. The NIR spectra of these samples are overlayed in Figure 8.12. These spectra contain 141 X-variables each, which cover the wavelength range of 1570-1850 nm. 

Bradford and Vanderhoff (20) have also prepared films from crosslinked latex particles. These authors studied a 65 35 styrene-butadiene copolymer crosslinked with varying amounts of divinylbenzene and found that although the incorporation of divinylbenzene retarded the coalescence of latex particles, these particles did indeed coalesce, presumably due to a similar interdiffusion of polymer chain ends. 

Of the 17 billion lb of butadiene consumed in 1999, almost two thirds went into the production of elastomers (styrene-butadiene latex rubber (SBR), polybutadiene, nitrile, and polychloroprene). Adiponitrile, ABS resins, styrene-butadiene latex, styrene block copolymers, and other smaller polymer uses accounted for the remainder. The largest single use was for styrene-butadiene copolymers (SBR and latex). Most of it was made by an emulsion process using a free-radical initiator and a styrene-butadiene ratio of about 1 3. More detailed description of the rubber and polymer used can be found in Chapters 16 and 15. 

Figure 12.6. Volume resistivity against filler loading for SBR composites filled with MWNTs and mixtures (10 phr CB + x phr (MWNTs) (A) and TEM image of a styrene-butadiene copolymer (SBR) containing a dual filling (5 phr CB + 5 phr MWNTs) (B). [Reprinted from L. Bokobza, M. Rahmani, C. Belin, J.-L. Bruneel, N.-E. El Bounia "Blends of carbon blacks and multwall carbon nanotubes as reinforcing fillers for hydrocarbon rubbers", Journal of Polymer Science Part B Polymer Physics, 46,1939,2008, permission from John Wiley and Sons].

Fig.4.a Cole-Cole like plots of the strain sweep data from Fig. 1 (polymer matrix natural rubber).b Similar shaped Cole-Cole plots under equal testing conditions in synthetic rubber samples containing the same carbon blacks as indicated in Fig. 4a. The synthetic polymer networks consist of statistical styrene-butadiene copolymers with 23 wt % styrene content (SBR 1500)...

When only spectroscopic methods are used, they are able to identify polymer components with respect to their chemical nature. However, in many cases, they are unable to answer the question whether two chemical structures are combined to yield a copolymer or a blend or both. For example, analyzing a rubber mixture one is able to identify styrene and butadiene as the monomer units. However, using FTIR or NMR it is impossible to decide if the sample is a mixture of polystyrene (PS) and polybutadiene (PB),or a copolymer of styrene and butadiene, or a blend of a styrene-butadiene copolymer and PB. For the latter case, even the copolymer composition cannot be determined just by running a FTIR or NMR spectrum. 

Guo X and Rempel G L. (1992) Catalytic hydrosilylation of diene-based polymers. 2. HydrosUylationof styrene-butadiene copolymer andnitrile-butadiene copolymer. Macromolecules 25 883-886... 

---