Solubility poly

Monopnictides, plutonium, 7.9 691 Monopolar electrodes, 9 621 Mono/poly soluble dyes, 7 373t Monopotassium phosphate (MKP),... 

N-Benzylamides are recommended when the corresponding acid is liquid and/or water-soluble so that it cannot itself serve as a derivative. Phe benzylamides derived from the simple fatty acids or their esters are not altogether satisfactory (see Table below) those derived from most hydroxy-acids and from poly basic acids or their esters are formed in good yield and are easily purified. The esters of aromatic acids yield satisfactory derivatives but the method must compete with the equally simple process of hydrolysis and precipitation of the free acid, an obvious derivative when the acid is a solid. The procedure fails with esters of keto, sul phonic, inorganic and some halogenated aliphatic esters. 

Mono- and di saccharides are colourless solids or sjrrupy liquids, which are freely soluble in water, practically insoluble in ether and other organic solvents, and neutral in reaction. Polysaccharides possess similar properties, but are generally insoluble in water because of their high molecular weights. Both poly- and di-saccharides are converted into monosaccharides upon hydrolysis. 

When dealing with esters of water-soluble, non steam-volatile, poly-hydric alcohols e.g., ethylene glycol or glycerol), the distillate consists of water only (density 1 00). The water soluble, non-volatile alcohol may be isolated by evaporation of the alkahne solution to a thick syrup on a water bath and extraction of the polyhydric alcohol from the salt with cold ethyl alcohol. 

Polyphenylene polymers can be prepared by this coupling. For example, the preparation of poly(/i-quaterphenylene-2,2 -dicarboxylic acid) (643) was carried out using aqueous NaHCO and a water-soluble phosphine ligand (DPMSPP)[5I I]. Branched polyphenylene was also prepared[5l2). 

Poly(vinyl alcohol) is a useful water soluble polymer It cannot be prepared directly from vinyl alcohol because of the rapidity with which vinyl alcohol (H2C=CHOH) isomenzes to acetaldehyde Vinyl acetate however does not rearrange and can be polymerized to poly(vinyl acetate) How could you make use of this fact to prepare poly(vinyl alcohol)" ... 

Polylacrylic Acid) and Poly(methacrylic Acid). Glacial acrylic acid and glacial meth-acrylic acid can be polymerized to produce water-soluble polymers having the following structures ... 

Ester interchange reactions are valuable, since, say, methyl esters of di-carboxylic acids are often more soluble and easier to purify than the diacid itself. The methanol by-product is easily removed by evaporation. Poly (ethylene terephthalate) is an example of a polymer prepared by double application of reaction 4 in Table 5.3. The first stage of the reaction is conducted at temperatures below 200°C and involves the interchange of dimethyl terephthalate with ethylene glycol... 

Dichromated Resists. The first compositions widely used as photoresists combine a photosensitive dichromate salt (usually ammonium dichromate) with a water-soluble polymer of biologic origin such as gelatin, egg albumin (proteins), or gum arabic (a starch). Later, synthetic polymers such as poly(vinyl alcohol) also were used (11,12). Irradiation with uv light (X in the range of 360—380 nm using, for example, a carbon arc lamp) leads to photoinitiated oxidation of the polymer and reduction of dichromate to Ct(III). The photoinduced chemistry renders exposed areas insoluble in aqueous developing solutions. The photochemical mechanism of dichromate sensitization of PVA (summarized in Fig. 3) has been studied in detail (13). 

Polyoxyethylene. Synthetic polymers with a variety of compositionaHy similar chemical stmctures are as follows. Based on polarity, poly(oxymethylene) (1) would be expected to be water soluble. It is a highly crystalline polymer used in engineering plastics, but it is not water-soluble (see... 

Cationic monomers are used to enhance adsorption on waste soHds and faciHtate flocculation (31). One of the first used in water treatment processes (10) is obtained by the cyclization of dimethyldiallylammonium chloride in 60—70 wt % aqueous solution (43) (see Water). Another cationic water-soluble polymer, poly(dimethylarnine-fi9-epichlorohydrin) (11), prepared by the step-growth... 

Two inorganic water-soluble polymers, both polyelectrolytes in their sodium salt forms, have been known for some time poly(phosphoric acid) (12) and poly(siHcic acid) (13). A more exciting inorganic water-soluble polymer with nonionic... 

It is evident that the area of water-soluble polymer covets a multitude of appHcations and encompasses a broad spectmm of compositions. Proteins (qv) and other biological materials ate coveted elsewhere in the Eniyclopedia. One of the products of this type, poly(aspartic acid), may be developed into interesting biodegradable commercial appHcations (70,71). 

Cellulosics. CeUulosic adhesives are obtained by modification of cellulose [9004-34-6] (qv) which comes from cotton linters and wood pulp. Cellulose can be nitrated to provide cellulose nitrate [9004-70-0] which is soluble in organic solvents. When cellulose nitrate is dissolved in amyl acetate [628-63-7] for example, a general purpose solvent-based adhesive which is both waterproof and flexible is formed. Cellulose esterification leads to materials such as cellulose acetate [9004-35-7], which has been used as a pressure-sensitive adhesive tape backing. Cellulose can also be ethoxylated, providing hydroxyethylceUulose which is useful as a thickening agent for poly(vinyl acetate) emulsion adhesives. Etherification leads to materials such as methylceUulose [9004-67-5] which are soluble in water and can be modified with glyceral [56-81-5] to produce adhesives used as wallpaper paste (see Cellulose esters Cellulose ethers). 

Water-Soluble Films. Water-soluble films can be produced from such polymers as poly(vinyl alcohol) (PVOH), methylceUulose, poly(ethylene oxide), or starch (qv) (see Cellulose ethers Polyethers Vinyl polymers). Water-soluble films are used for packaging and dispensing portions of detergents, bleaches, and dyes. A principal market is disposable laundry bags for hospital use. Disposal packaging for herbicides and insecticides is an emerging use. 

Suspension polymerization of VDE in water are batch processes in autoclaves designed to limit scale formation (91). Most systems operate from 30 to 100°C and are initiated with monomer-soluble organic free-radical initiators such as diisopropyl peroxydicarbonate (92—96), tert-huty peroxypivalate (97), or / fZ-amyl peroxypivalate (98). Usually water-soluble polymers, eg, cellulose derivatives or poly(vinyl alcohol), are used as suspending agents to reduce coalescence of polymer particles. Organic solvents that may act as a reaction accelerator or chain-transfer agent are often employed. The reactor product is a slurry of suspended polymer particles, usually spheres of 30—100 pm in diameter they are separated from the water phase thoroughly washed and dried. Size and internal stmcture of beads, ie, porosity, and dispersant residues affect how the resin performs in appHcations. 

It has also been found that polymers possessing functional groups such as amines and pyridines are soluble in pregeUed sol solutions, especially, poly(2-vin5ipyridine) and poly(N-vinylpyrroHdinone) (PVP) (49). There, materials were made as part of a study of the synthesis of nonshrinking sol—gel-derived networks (49). 

Synthesis and Properties. Several methods have been suggested to synthesize polyimides. The predominant one involves a two-step condensation reaction between aromatic diamines and aromatic dianhydrides in polar aprotic solvents (2,3). In the first step, a soluble, linear poly(amic acid) results, which in the second step undergoes cyclodehydration, leading to an insoluble and infusible PL Overall yields are generally only 70—80%. 

Poly(phenylquinoxaline—arnide—imides) are thermally stable up to 430°C and are soluble in polar organic solvents (17). Transparent films of these materials exhibit electrical insulating properties. Quinoxaline—imide copolymer films prepared by polycondensation of 6,6 -meth5lene bis(2-methyl-3,l-benzoxazine-4-one) and 3,3, 4,4 -benzophenone tetracarboxyUc dianhydride and 4,4 -oxydianiline exhibit good chemical etching properties (18). The polymers are soluble, but stable only up to 200—300°C. 

In addition to providing fully alkyl/aryl-substituted polyphosphasenes, the versatility of the process in Figure 2 has allowed the preparation of various functionalized polymers and copolymers. Thus the monomer (10) can be derivatized via deprotonation—substitution, when a P-methyl (or P—CH2—) group is present, to provide new phosphoranimines some of which, in turn, serve as precursors to new polymers (64). In the same vein, polymers containing a P—CH group, for example, poly(methylphenylphosphazene), can also be derivatized by deprotonation—substitution reactions without chain scission. This has produced a number of functionalized polymers (64,71—73), including water-soluble carboxylate salts (11), as well as graft copolymers with styrene (74) and with dimethylsiloxane (12) (75). 

Examples of polymers which form anisotropic polymer melts iaclude petroleum pitches, polyesters, polyethers, polyphosphaziaes, a-poly- -xyljlene, and polysdoxanes. Synthesis goals iaclude the iacorporation of a Hquid crystal-like entity iato the maia chaia of the polymer to iacrease the strength and thermal stabiHty of the materials that are formed from the Hquid crystal precursor, the locking ia of Hquid crystalline properties of the fluid iato the soHd phase, and the production of extended chain polymers that are soluble ia organic solvents rather than sulfuric acid. 

Poly(alI lene glycol)s. While these can be made from polymeri2ation of any alkylene oxide, they are usually prepared either from propylene oxide as the water-insoluble type, or as water-soluble copolymers of propylene oxide and up to 50% ethylene oxide (35,36) (see Polyethers, propylene OXIDE polymers). Current worldwide production is estimated to be about 45,000 t. 

Poly(alkylene glycol)s have a number of characteristics that make them desirable as lubricants. Compared to petroleum lubricants, they have lower pour points, a higher viscosity index, and a wider range of solubilities including water, compatibility with elastomers, less tendency to form tar and sludge, and lower vapor pressure (35). 

HoUow-fiber fabrication methods can be divided into two classes (61). The most common is solution spinning, in which a 20—30% polymer solution is extmded and precipitated into a bath of a nonsolvent, generally water. Solution spinning allows fibers with the asymmetric Loeb-Soufirajan stmcture to be made. An alternative technique is melt spinning, in which a hot polymer melt is extmded from an appropriate die and is then cooled and sohdified in air or a quench tank. Melt-spun fibers are usually relatively dense and have lower fluxes than solution-spun fibers, but because the fiber can be stretched after it leaves the die, very fine fibers can be made. Melt spinning can also be used with polymers such as poly(trimethylpentene), which are not soluble in convenient solvents and are difficult to form by wet spinning. 

Almost all synthetic binders are prepared by an emulsion polymerization process and are suppHed as latexes which consist of 48—52 wt % polymer dispersed in water (101). The largest-volume binder is styrene—butadiene copolymer [9003-55-8] (SBR) latex. Most SBRlatexes are carboxylated, ie, they contain copolymerized acidic monomers. Other latex binders are based on poly(vinyl acetate) [9003-20-7] and on polymers of acrylate esters. Poly(vinyl alcohol) is a water-soluble, synthetic biader which is prepared by the hydrolysis of poly(viayl acetate) (see Latex technology Vinyl polymers). 

---