Chain-scission

In chain scission we have bonds broken at random within the polymer molecules. Each breaking bond creates another molecule and lowers the average molecular weight. Hydrolysis of a polyester is a good example of a random scission process, since the susceptibility of a bond does not depend greatly on molecular size. If we take a polyester of number-average degree of polymerization in a dilute solution of concentration c (g/dl), we can calculate the concentration of ester bonds in the system [([)]  

N is the concentration of monomer units in solution m is the concentration of polymer molecules 

If we postulate that the rate of bond disappearance (hydrolysis) with time (-d[ )]/dO will be proportional to the bond concentration [ )], we have a first-order expression  

differentiating the second and fourth expressions of the above equation yields 

But in Equation 12.6, l/x is much less than 1 therefore, the reaction is pseudo-zero- 

---

Hoffman Degradation. Polyacrylamide reacts with alkaline sodium hypochlorite [7681-52-9], NaOCl, or calcium hypochlorite [7778-54-3], Ca(OCl)2, to form a polymer with primary amine groups (58). Optimum conditions for the reaction include a slight molar excess of sodium hypochlorite, a large excess of sodium hydroxide, and low temperature (59). Cross-linking sometimes occurs if the polymer concentration is high. High temperatures can result in chain scission. 

Both side-chain and main-chain scission products are observed when polyacrylates are irradiated with gamma radiation (60). The nature of the alkyl side group affects the observed ratio of these two processes (61,62). 

Crystallinity has been studied by x-ray irradiation (85). An initial increase caused by chain scission in the amorphous phase was followed (above 3 kGy or 3 X 10 rad) by a gradual decrease associated with a disordering of the crystallites. The amorphous component showed a maximum of radiation-induced broadening in the nmr at 7 kGy (7 x 10 rad). 

In addition to providing fully alkyl/aryl-substituted polyphosphasenes, the versatility of the process in Figure 2 has allowed the preparation of various functionalized polymers and copolymers. Thus the monomer (10) can be derivatized via deprotonation—substitution, when a P-methyl (or P—CH2—) group is present, to provide new phosphoranimines some of which, in turn, serve as precursors to new polymers (64). In the same vein, polymers containing a P—CH group, for example, poly(methylphenylphosphazene), can also be derivatized by deprotonation—substitution reactions without chain scission. This has produced a number of functionalized polymers (64,71—73), including water-soluble carboxylate salts (11), as well as graft copolymers with styrene (74) and with dimethylsiloxane (12) (75). 

Although primary and secondary alkyl hydroperoxides are attacked by free radicals, as in equations 8 and 9, such reactions are not chain scission reactions since the alkylperoxy radicals terminate by disproportionation without forming the new radicals needed to continue the chain (53). Overall decomposition rates are faster than the tme first-order rates if radical-induced decompositions are not suppressed. 

Oxidation. AH polyamides are susceptible to oxidation. This involves the initial formation of a free radical on the carbon alpha to the NH group, which reacts to form a peroxy radical with subsequent chain reactions leading to chain scission and yellowing. As soon as molten nylon is exposed to air it starts to discolor and continues to oxidize until it is cooled to below 60°C. It is important, therefore, to minimize the exposure of hot nylon to air to avoid discoloration or loss of molecular weight. Similarly, nylon parts exposed to high temperature in air lose their properties with time as a result of oxidation. This process can be minimized by using material containing stabilizer additives. 

When the polymers are exposed to ultraviolet radiation, the activated ketone functionahties can fragment by two different mechanisms, known as Norrish types I and II. The degradation of polymers with the carbonyl functionahty in the backbone of the polymer results in chain cleavage by both mechanisms, but when the carbonyl is in the polymer side chain, only Norrish type II degradation produces main-chain scission (37,49). A Norrish type I reaction for backbone carbonyl functionahty is shown by equation 5, and a Norrish type II reaction for backbone carbonyl functionahty is equation 6. 

Norrish type I chemistry is claimed to be responsible for about 15% of the chain scission of ethylene—carbon monoxide polymers at room temperature, whereas at 120°C it promotes 59% of the degradation. Norrish I reactions are independent of temperature and oxygen concentration at temperatures above the T of the polymer (50). 

Radiation-induced degradation reactions are in direct opposition to cross-linking or curing processes, in that the average molecular weight of the preformed polymer decreases because of chain scission and without any subsequent... 

Coagents ate often used with peroxides to increase the state of cure. Some coagents, such as polybutadiene or multifimctional methacrylates, are used at high levels to form polymer grafts or interpenetrating networks. Other coagents such as triaHyl cyanurate, triaHyl trimelHtate, and y /i -phenjiene bismaleimide are used at low levels to reduce the tendency of the polymer to degrade by chain scission. 

Attaching the ketone groups to the polymer backbone is more efficient on a chain scission/ketone basis because some of the light energy that the pendent ketone absorbs leads direcdy to chain scission via the Norrish type II mechanism, as well as photooxidation via the Norrish type I mechanism (see... 

Polymer units formed by either 3,4- or 1,4-addition do not evolve hydrogen chloride under these conditions in the absence of oxygen. Also, chain scission resulting in the formation of lower molecular weight polymers does not occur (104). 

Benzene rings in both the skeleton structure and on the side groups can be subjected to substitution reactions. Such reactions do not normally cause great changes in the fundamental nature of the polymer, for example they seldom lead to chain scission or cross-linking. 

Chain scission—resulting in a loss in strength and toughness. 

The proximity of the methyl group to the double bond in natural rubber results in the polymer being more reactive at both the double bond and at the a-methylenic position than polybutadiene, SBR and, particularly, polychlor-oprene. Consequently natural rubber is more subject to oxidation, and as in this case (c.f. polybutadiene and SBR) this leads to chain scission the rubber becomes softer and weaker. As already stated the oxidation reaction is considerably affected by the type of vulcanisation as well as by the use of antioxidants. 

---