Batteries, lithium type

Selenium and selenium compounds are also used in electroless nickel-plating baths, delayed-action blasting caps, lithium batteries, xeroradiography, cyanine- and noncyanine-type dyes, thin-film field effect transistors (FET), thin-film lasers, and fire-resistant functional fluids in aeronautics (see... 

A second type of soHd ionic conductors based around polyether compounds such as poly(ethylene oxide) [25322-68-3] (PEO) has been discovered (24) and characterized. These materials foUow equations 23—31 as opposed to the electronically conducting polyacetylene [26571-64-2] and polyaniline type materials. The polyethers can complex and stabilize lithium ions in organic media. They also dissolve salts such as LiClO to produce conducting soHd solutions. The use of these materials in rechargeable lithium batteries has been proposed (25). 

Security type attache cases incorporating lithium batteries and/or pyrotechnic material Selenium nitride Silver acetylide (dry)... 

Apart from the improvement and scaling up of known systems such as the lead accumulator or the nickel/cadmium cell, new types of cells have also been developed. Here, rechargeable lithium batteries and nickel-systems seem to be the most promising the reason for this will be apparent from the following sections [3]. 

Li-Mn02 batteries are available in a variety of shapes and construction [30] in accordance with their particular use. Figure 32 shows various applications of lithium batteries based on their drain current. Coin-type batteries are generally used for low-rate drain. Cylindrical batteries with the inside-out construction can serve as a... 

Table 1. Specifications of coin-type manganese dioxide-lithium batteries...

This section reports on the current state of knowledge on nonaqueous electrolytes for lithium batteries and lithium-ion batteries. The term electrolyte in the current text refers to an ion-conducting solution which consists of a solvent S and a salt, here generally a lithium salt. Often 1 1-salts of the LiX type are preferred for reasons given below only a few l 2-salts Li2X have attained some importance for batteries, and 1 3-salts Li3X are not in use. 

The electrochemical intercalation/insertion is not a special property of graphite. It is apparent also with many other host/guest pairs, provided that the host lattice is a thermodynamically or kinetically stable system of interconnected vacant lattice sites for transport and location of guest species. Particularly useful are host lattices of inorganic oxides and sulphides with layer or chain-type structures. Figure 5.30 presents an example of the cathodic insertion of Li+ into the TiS2 host lattice, which is practically important in lithium batteries. 

Battery technology has developed enormously in recent years. One of the most useful types of batteries is known as the lithium battery, but there are actually several designs only one of which will be described. In one of the types, the anode is constructed of lithium or a lithium alloy hence the name. A graphite cathode is used, and the electrolyte is a solution of Li[AlCl4] in thionyl chloride. At the anode, lithium is oxidized,... 

Another issue with metals is availability. For example, cobalt is not produced in the United States, but it used extensively in a wide variety of alloys and in the production of one of the most common types of lithium batteries. The availability of cobalt is crucial to several segments of American industry. For example, batteries being developed for use in automobiles powered by alternate energy sources are currently envisioned to use a lithium ion battery that also contains cobalt. However, cobalt is not the only strategic metal, and there is concern about the availability of several metals that are vital to industries in the United States, China, and Japan. There will be competition and stockpiling of strategic metals as the reserves become less accessible. 

The electronic circuit of the safety sensor consists of a p-type silicon electrode, an LED, a resistor, two 3 V lithium batteries, and a platinum wire as a counter electrode, connected in series, as shown in the right part of Fig. 10.7. These components are assembled in a pen-like housing, optimized to measure even thin layers of liquid on a flat surface, as shown in the left part of Fig. 10.7. This configuration is advantageous if a puddle, observed for example under a wet bench or other equipment, is to be analyzed. 

At this time the only commercially available all-solid-state cell is the lithium battery containing Lil as the electrolyte. Many types of solid lithium ion conductors including inorganic crystalline and glassy materials as well as polymer electrolytes have been proposed as separators in lithium batteries. These are described in the previous chapters. A suitable solid electrolyte for lithium batteries should have the properties... 

A number of researchers, ° ° particularly in Japan, have been pursuing the oxides of iron as potential cathode materials for lithium cells. However, materials of the type LiFeOz have shown little ability for lithium removal. A number of other iron compounds have been studied over the years, including FeOCl, ° FePS3, ° KFeSz, and FeSz, but none showed much reversibility. Although metal phosphates have been studied for more than 20 years since the discovery of fast ion transport in NASICON, it is only recently that they have been considered as cathodes or anodes " of lithium batteries. 

Table 1. Types of Separators Used in Different Type of Secondary Lithium Batteries...

Lithium secondary batteries can be classified into three types, a liquid type battery using liquid electrolytes, a gel type battery using gel electrolytes mixed with polymer and liquid, and a solid type battery using polymer electrolytes. The types of separators used in different types of secondary lithium batteries are shown in Table 1. The liquid lithium-ion cell uses microporous polyolefin separators while the gel polymer lithium-ion cells either use a PVdF separator (e.g. PLION cells) or PVdF coated microporous polyolefin separators. The PLION cells use PVdF loaded with silica and plasticizer as separator. The microporous structure is formed by removing the plasticizer and then filling with liquid electrolyte. They are also characterized as plasticized electrolyte. In solid polymer lithium-ion cells, the solid electrolyte acts as both electrolyte and separator. 

To overcome the poor mechanical properties of polymer and gel polymer type electrolytes, microporous membranes impregnated with gel polymer electrolytes, such as PVdF. PVdF—HFP. and other gelling agents, have been developed as an electrolyte material for lithium batteries.Gel coated and/ or gel-filled separators have some characteristics that may be harder to achieve in the separator-free gel electrolytes. For example, they can offer much better protection against internal shorts when compared to gel electrolytes and can therefore help in reducing the overall thickness of the electrolyte layer. In addition the ability of some separators to shutdown... 

Recently, new types of organic positives, formed by a mixture of dimercaptan with polyaniline, have been reported. These composite materials appear to have an energy density higher than that of most inorganic intercalation oxides and good cyclability. However, use of these materials in practical rechargeable lithium batteries has still to be confirmed. 

---