Copolymers glycol

The same features, however, proved successful in the commercial use of the poly(alkylene oxide)s as machine lubricants, metal-working lubricants, quenchants, and hydraulic fluids. The solubility of ethylene oxide/ propylene oxide copolymer glycols in water has led these formulations to be universally accepted as "hydrolubes" and brake fluids where the nonflammability and wide temperature service range of a blend of polyol and water are key features. 

Materials that typify thermoresponsive behavior are polyethylene—poly (ethylene glycol) copolymers that are used to functionalize the surfaces of polyethylene films (smart surfaces) (20). When the copolymer is immersed in water, the poly(ethylene glycol) functionaUties at the surfaces have solvation behavior similar to poly(ethylene glycol) itself. The abiUty to design a smart surface in these cases is based on the observed behavior of inverse temperature-dependent solubiUty of poly(alkene oxide)s in water. The behavior is used to produce surface-modified polymers that reversibly change their hydrophilicity and solvation with changes in temperatures. Similar behaviors have been observed as a function of changes in pH (21—24). 

Acryhc stmctural adhesives have been modified by elastomers in order to obtain a phase-separated, toughened system. A significant contribution in this technology has been made in which acryhc adhesives were modified by the addition of chlorosulfonated polyethylene to obtain a phase-separated stmctural adhesive (11). Such adhesives also contain methyl methacrylate, glacial methacrylic acid, and cross-linkers such as ethylene glycol dimethacrylate [97-90-5]. The polymerization initiation system, which includes cumene hydroperoxide, N,1S7-dimethyl- -toluidine, and saccharin, can be apphed to the adherend surface as a primer, or it can be formulated as the second part of a two-part adhesive. Modification of cyanoacrylates using elastomers has also been attempted copolymers of acrylonitrile, butadiene, and styrene ethylene copolymers with methylacrylate or copolymers of methacrylates with butadiene and styrene have been used. However, because of the extreme reactivity of the monomer, modification of cyanoacrylate adhesives is very difficult and material purity is essential in order to be able to modify the cyanoacrylate without causing premature reaction. 

Poly(alI lene glycol)s. While these can be made from polymeri2ation of any alkylene oxide, they are usually prepared either from propylene oxide as the water-insoluble type, or as water-soluble copolymers of propylene oxide and up to 50% ethylene oxide (35,36) (see Polyethers, propylene OXIDE polymers). Current worldwide production is estimated to be about 45,000 t. 

Alkenylsuccinic anhydrides made from several linear alpha olefins are used in paper sizing, detergents, and other uses. Sulfosuccinic acid esters serve as surface active agents. Alkyd resins (qv) are used as surface coatings. Chlorendric anhydride [115-27-5] is used as a flame resistant component (see Flame retardants). Tetrahydrophthalic acid [88-98-2] and hexahydrophthalic anhydride [85-42-7] have specialty resin appHcations. Gas barrier films made by grafting maleic anhydride to polypropylene [25085-53-4] film are used in food packaging (qv). Poly(maleic anhydride) [24937-72-2] is used as a scale preventer and corrosion inhibitor (see Corrosion and corrosion control). Maleic anhydride forms copolymers with ethylene glycol methyl vinyl ethers which are partially esterified for biomedical and pharmaceutical uses (189) (see Pharmaceuticals). 

Thermoplastic copolyester elastomers are generally block copolymers produced from short-chain aUphatic diols, aromatic diacids, and polyalkjlene ether-diols. They are often called polyesterether or polyester elastomers. The most significant commercial product is the copolymer from butane-l,4-diol, dimethyl terephthalate, and polytetramethylene ether glycol [25190-06-1J, which produces a segmented block copolyesterether with the following stmcture. 

Poly(propylene oxide) [25322-69-4] may be abbreviated PPO and copolymers of PO and ethylene oxide (EO) are referred to as EOPO. Diol poly(propylene oxide) is commonly referred to by the common name poly(propylene glycol) (PPG). Propylene oxide [75-56-9] and poly(propylene oxide) and its copolymers, with ethylene oxide, have by far the largest volume and importance in the polyurethane (PUR) and surfactant industry compared to all other polyepoxides. Articles reviewing propylene oxide (1), poly(propylene oxide) (2—4), other poly(aIkylene oxides) (4), and polyurethanes (5—7) are cited to lead the interested reader to additional detail not in the scope of this article. 

In order to achieve the desired fiber properties, the two monomers were copolymerized so the final product was a block copolymer of the ABA type, where A was pure polyglycoHde and B, a random copolymer of mostly poly (trimethylene carbonate). The selected composition was about 30—40% poly (trimethylene carbonate). This suture reportedly has exceUent flexibiHty and superior in vivo tensile strength retention compared to polyglycoHde. It has been absorbed without adverse reaction ia about seven months (43). MetaboHsm studies show that the route of excretion for the trimethylene carbonate moiety is somewhat different from the glycolate moiety. Most of the glycolate is excreted by urine whereas most of the carbonate is excreted by expired CO2 and uriae. 

Polyether Polyols. Polyether polyols are addition products derived from cyclic ethers (Table 4). The alkylene oxide polymerisation is usually initiated by alkah hydroxides, especially potassium hydroxide. In the base-catalysed polymerisation of propylene oxide, some rearrangement occurs to give aHyl alcohol. Further reaction of aHyl alcohol with propylene oxide produces a monofunctional alcohol. Therefore, polyether polyols derived from propylene oxide are not truly diftmctional. By using sine hexacyano cobaltate as catalyst, a more diftmctional polyol is obtained (20). Olin has introduced the diftmctional polyether polyols under the trade name POLY-L. Trichlorobutylene oxide-derived polyether polyols are useful as reactive fire retardants. Poly(tetramethylene glycol) (PTMG) is produced in the acid-catalysed homopolymerisation of tetrahydrofuran. Copolymers derived from tetrahydrofuran and ethylene oxide are also produced. 

Commercial thermoplastic polyesters are synthesized in a similar way by the reaction of a relatively high molecular-weight polyether glycol with butanediol and dimethyl terephthalate (14,15). The polyether chain becomes the soft segment in the final product, whereas the terephthaUc acid—butanediol copolymer forms the hard crystalline domains. 

Over the past years considerable attention has been paid to the dispersing system since this controls the porosity of the particle. This is important both to ensure quick removal of vinyl chloride monomer after polymerisation and also to achieve easy processing and dry blendable polymers. Amongst materials quoted as protective colloids are vinyl acetate-maleic anhydride copolymers, fatty acid esters of glycerol, ethylene glycol and pentaerythritol, and, more recently, mixed cellulose ethers and partially hydrolysed polyfvinyl acetate). Much recent emphasis has been on mixed systems. 

Nylons 46, 6, 66, 610, 11 and 12 are polar crystalline materials with exceptionally good resistance to hydrocarbons. Esters, alkyl halides, and glycols have little effect. Alcohols generally have some swelling action and may in fact dissolve some copolymers (e.g. nylon 66/610/6). There are few solvents for the nylons, of which the most common are formic acid, glacial acetic acid, phenols and cresols. 

Most of the commercial polymers consist of polyether blocks separated by polyamide blocks. The polyether blocks may be based on polyethylene glycol, polypropylene glycol or, more commonly, polytetramethylene ether glycol. The polyamides are usually based on nylon 11 but may be based on nylons 6 or 66 even a copolymer, e.g. 6/11. 

In 1978 Hiils (Mumcu et al ) described the properties of a block copolymer prepared by condensation of polytetramethylene ether glycol with laurin lactam and decane-1,10-dicarboxylic acid. The materials were introduced as XR3808 and X4006. The polyamide XR3808 is reported to have a specific gravity of 1.02, a yield stress of 24 MPa, a modulus of elasticity of 300 MPa and an elongation of break of 360%. The Swiss company Emser Werke also introduced similar... 

Another amorphous terephthalate has also been introduced commercially. This is a copolymer based on 1,4-cyclohexylene glycol with a combination of terephthalic acid and isophthalic acid. The copolymer is claimed to have excellent optical properties, have low moulding shrinkage and be relatively easy to vaccum form. As with other terephthalates it is considered in more detail in Chapter 25. 

In 1972 Eastman Kodak introduced a copolymer produced by reacting 1,4-cyclohexylene glycol with a mixture of isophthalic and terephthalic acids. Thus the polymer contains 1,4-cyclohexanedimethyloxy units (I), terephthalic acid units (II) and isophthalic acid units (III) Figure 25.20). 

---