Poly propylene

In polymers made of dis-symmetric monomers, such as, for example, poly(propylene), the stmcture may be irregular and constitutional isomerism can occur as shown in figure C2.1.1(a ). The succession of the relative configurations of the asymmetric centres can also vary between stretches of the chain. Configuration isomerism is characterized by the succession of dyads which are named either meso, if the two asymmetric centres have the same relative configurations, or racemo if the configurations differ (figure C2.1.1(b )). A polymer is called isotactic if it contains only one type of dyad and syndiotactic if the dyad sequence strictly alternates between the meso and racemo fonns. 

Figure C2.1.1. (a) Constitutional isomerism of poly (propylene). The upper chain has a regular constitution. The lower one contains a constitutional defect, (b) Configurational isomerism of poly(propylene). Depending on tire relative configurations of tire asymmetric carbons of two successive monomer units, tire corresponding dyad is eitlier meso or racemo.

Alexandridis P and Hatton T A 1995 Poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) blook oopolymer surfaotants in aqueous solutions and at interfaoes thermodynamios, struoture, dynamios, modeling Colloids Surf. A 96 1-46... 

Bloor D M, Wan-Yunis W M Z, Wan-Badhi W A, Li Y, Hoizwarth J F and Wyn-Jones E 1995 Equilibrium and kinetio studies assooiated with the binding of sodium dodeoyl sulfate to the polymers poly(propylene oxide) and ethyl-(hydroxyethyl)oellulose Langmuir 3395-400... 

Poly(propylene oxide) [25322-69-4] may be abbreviated PPO and copolymers of PO and ethylene oxide (EO) are referred to as EOPO. Diol poly(propylene oxide) is commonly referred to by the common name poly(propylene glycol) (PPG). Propylene oxide [75-56-9] and poly(propylene oxide) and its copolymers, with ethylene oxide, have by far the largest volume and importance in the polyurethane (PUR) and surfactant industry compared to all other polyepoxides. Articles reviewing propylene oxide (1), poly(propylene oxide) (2—4), other poly(aIkylene oxides) (4), and polyurethanes (5—7) are cited to lead the interested reader to additional detail not in the scope of this article. 

Homopolymers of PO and other epoxides are named a number of ways after the monomer, eg, poly(propylene oxide) (PPO) or polymethjioxirane from a stmctural point of view, polyoxypropylene or poly(propylene glycol) or from the Chemicaly hstracts (CA) name, poly[oxy(methyl-l,2-ethanediyl)], a-hydro- CO-hydroxy-. Common names are used extensively in the Hterature and in this article. 

Fig. 1. Triad sequences for stereoregular poly(propylene oxide) where (a) shows isotactic (RRR or SSS), (b) syndiotactic (RSR or SRS), and (c) heterotactic...

The biodegradation of poly(alkylene glycols) is hindered by their lack of water solubiUty, and only the low oligomers of poly(propylene glycol) are biodegradable with any certainty (179—181), as are those of poly(tetramethylene glycol) (182). A similar xo-oxidation mechanism to that reported for poly(ethylene glycol) has been proposed. 

Molecular weights of poly(propylene oxide) polymers of greater than 100,000 are prepared from catalysts containing FeCl (40,41). The molecular weight of these polymers is gready increased by the addition of small amounts of organic isocyanates (42). Homopolymers of propylene oxide are also prepared by catalysis using diethylzinc—water (43), diphenylzinc—water (44), and trialkyl aluminum (45,46) systems. 

Natural Products. Many natural products, eg, sugars, starches, and cellulose, contain hydroxyl groups that react with propylene oxide. Base-cataly2ed reactions yield propylene glycol monoethers and poly(propylene glycol) ethers (61—64). Reaction with fatty acids results ia a mixture of mono- and diesters (65). Cellulose fibers, eg, cotton (qv), have been treated with propylene oxide (66—68). 

Polyurethane foams are formed by reaction with glycerol with poly(propylene oxide), sometimes capped with poly(ethylene oxide) groups with a reaction product of trimethylolpropane and propylene oxide or with other appropriate polyols. A typical reaction sequence is shown below, in which HO—R—OH represents the diol. If a triol is used, a cross-linked product is obtained. 

A second class of important electrolytes for rechargeable lithium batteries are soHd electrolytes. Of particular importance is the class known as soHd polymer electrolytes (SPEs). SPEs are polymers capable of forming complexes with lithium salts to yield ionic conductivity. The best known of the SPEs are the lithium salt complexes of poly(ethylene oxide) [25322-68-3] (PEO), —(CH2CH20) —, and poly(propylene oxide) [25322-69-4] (PPO) (11—13). Whereas a number of experimental battery systems have been constmcted using PEO and PPO electrolytes, these systems have not exhibited suitable conductivities at or near room temperature. Advances in the 1980s included a new class of SPE based on polyphosphazene complexes suggesting that room temperature SPE batteries may be achievable (14,15). 

Certain block copolymers have also found appHcation as surfactants (88). Eor example, AB or ABA block copolymers in which one block is hydrophilic and one block is hydrophobic have proven useful for emulsifying aqueous and non-aqueous substances and for wetting the surface of materials. Examples of such surfactants are the poly(propylene oxide- /oi / -ethylene oxide) materials, known as Pluronics (BASC Wyandotte Co.). 

In most cases, these active defoaming components are insoluble in the defoamer formulation as weU as in the foaming media, but there are cases which function by the inverted cloud-point mechanism (3). These products are soluble at low temperature and precipitate when the temperature is raised. When precipitated, these defoamer—surfactants function as defoamers when dissolved, they may act as foam stabilizers. Examples of this type are the block polymers of poly(ethylene oxide) and poly(propylene oxide) and other low HLB (hydrophilic—lipophilic balance) nonionic surfactants. 

Polyglycol Dow Chemical Co. poly(propylene oxide) used in latex and emulsion paints... 

Crystallinity is low the pendent allyl group contributes to the amorphous state of these polymers. Propylene oxide homopolymer itself has not been developed commercially because it cannot be cross-baked by current methods (18). The copolymerization of PO with unsaturated epoxide monomers gives vulcanizable products (19,20). In ECH—PO—AGE, poly(ptopylene oxide- o-epichlorohydrin- o-abyl glycidyl ether) [25213-15-4] (5), and PO—AGE, poly(propylene oxide-i o-abyl glycidyl ether) [25104-27-2] (6), the molar composition of PO ranges from approximately 65 to 90%. 

Molecular weight determinations of ECH—EO, ECH—AGE, ECH—EO—AGE, ECH—PO—AGE, and PO—AGE have not been reported. Some solution studies have been done on poly(propylene oxide), and these may approximate solution behavior of the PO—AGE copolymer (33,34). 

Nonionic Surface-Active Agents. Approximately 14% of the ethyleae oxide consumed ia the United States is used in the manufacture of nonionic surfactants. These are derived by addition of ethylene oxide to fatty alcohols, alkylphenols (qv), tall oil, alkyl mercaptans, and various polyols such as poly(propylene glycol), sorbitol, mannitol, and cellulose. They are used in household detergent formulations, industrial surfactant appHcations, in emulsion polymeri2ation, textiles, paper manufacturing and recycling, and for many other appHcations (281). 

Poly- propylene poly- ethylene CAB" ABSf PVC Saran Polyester glass 1 Epoxy glass phenolic asbestos Fluoro- carbons Chlorinated polyether (Penton) Poly- carbonate... 

Mention should be made of the nomenclature for the polymer. Industrially the materially is invariably known in the English-speaking world as polypropylene. However, the lUPAC name for the monomer is propene and until 1975 the recommended lUPAC name was polypropene, a term very rarely used. The latest lUPAC rules base the name of a polymer on the constitutional repeating unit, which in this case is a propylene unit (c.f. a methylene unit for polyethylene) and this leads to the name poly(propylene) (i.e. with brackets). In this volume the more common, unbracketed but still unambiguous name will be used. 

Low molecular weight liquid polyester resins are useful as plasticisers, particularly for PVC, where they are less volatile and have greater resistance to extraction by water than monomeric plasticisers. Examples of such plasticisers are polyfpropylene adipate) and poly(propylene sebacate). In some cases monobasic acids such as lauric acid are used to control the molecular weight. 

Partially vulcanized EPDM/Poly- propylene blend" Completely vulcanized EPDM/Poly- propylene blend Neoprene vulcanizate Ester-ether copolymer thermoplastic elastomer ... 

Figure 2 Light permeability of polyolefins after quenching (1-4) and of nonquenched samples (l -4 ) l,l -poly-propylene (PP) 2,2 -high-pressure polyethylene (HPPE) 3,3 -low-pressure polyethylene (LPPE) 4,4 -medium-pres-sure polyethylene (MPPE). Film thickness-150 fic moulding time-10 minutes, moulding pressure HPPE-160°C LPPE, MPPE, PP-190-200X.

---