Channel, definition

A native oxide layer on an n-type mercury cadmium telluride substrate 11 is used in combination with ZnS to provide first level insulation 12. The ZnS is deposited by thermal evaporation and an opaque field plate is provided for signal channel definition. Second level insulation of ZnS is deposited. This layer is thicker than the first level, and is provided with a stepped or sloped geometry under the first level gates. Input and output diodes are provided with MIS guard rings to increase breakdown voltages. 

The positron source, 120 kBq of Na, was deposited onto a Kapton foil covered with identical foil and sealed. The foil 8 pm thick absorbed 10% of positrons in polyimides Ps does not form and annihilation in the source envelope gave one component only = 374 ps, which must be taken into account. The source was sandwiched between two samples of the material studied and placed into a container in a vacuum chamber. The source-sample sandwich was viewed by two Pilot U scintillators coupled to XP2020Q photomultipliers. The resolution of our spectrometer with a stop window broadened to 80% (in order to register the greatest number of three-quantum decays) was 300 ps FWHM. The finite resolution had no influence on the results of our experiment as FWHM was still comparable to the channel definition At = 260 ps.The positron lifetime spectra were stored in 8000 channels of the Tennelec Multiport E analyser. 

A nonlinear side-chain polymer-based MZ interferometer has been reported [143], in which the channel definition was achieved through the change in refractive index caused by poling. A field of 100 MV m at a temperature of 90 °C yielded an index change of 0.06, sufficient to provide lateral confinement. Modulation at frequencies up to 1 kHz were achieved with drive voltage levels indicative of an electro-optic coefficient of 2.8mV ... 

Noncircular Channels Calciilation of fric tional pressure drop in noncircular channels depends on whether the flow is laminar or tumu-lent, and on whether the channel is full or open. For turbulent flow in ducts running full, the hydraulic diameter shoiild be substituted for D in the friction factor and Reynolds number definitions, Eqs. (6-32) and (6-33). The hydraiilic diameter is defined as four times the channel cross-sectional area divided by the wetted perimeter. For example, the hydraiilic diameter for a circiilar pipe is = D, for an annulus of inner diameter d and outer diameter D, = D — d, for a rectangiilar duct of sides 7, h, Dij = ah/[2(a + h)].T ie hydraulic radius Rii is defined as one-fourth of the hydraiilic diameter. 

Material-Flow Cbaracteristics Two important definitions of the flow characteristics of a storage vessel are mass flow, which means that all the material in the vessel moves whenever any is withdrawn (Fig. 21-17), and funnel flow, which occurs when only a portion of the material flows (usually in a channel or rathole in the center of the system) when any material is withdrawn (Fig. 21-18). Some typical mass-flow designs are shown in Fig. 21-19. 

Defining individual responsibilities and authority alone will not define how personnel relate to one another. Interrelation means to place in mutual relationship, so what is needed is a definition of the relationships between all staff with quality responsibilities. The primary reason for defining interrelationships is to establish channels of communication so that work proceeds smoothly without unplanned interruption. Staff need to know from whom they will receive their instructions, to whom they are accountable, to whom they should go to seek information to resolve difficulties, and to whom information or product should be submitted when complete. 

The annular flow pattern discussed above shows a definite connection with burn-out, and enables a simple burn-out mechanism to be set forth. There are many other flow patterns referred to in the literature, however, and we will consider here what can be said about any connection they may have with burn-out. It does not follow that there must be a connection, as a flow pattern is essentially a description of the bulk conditions in a channel and depends upon the none-too-reliable results of visual observation, which is often impeded by optical distortion. Thus, although gross conditions may appear to change and one pattern give way to another, the hydrodynamic state prevailing close to the heated surface may remain practically unaffected and the burn-out mechanisms unaltered. 

The definition of mini-channels and micro-channels has not been clearly and strictly established in the literature although many related studies have been done. For example, for compact heat exchangers, Mehendale et al. (1999) gave a relatively... 

Thus, the available data related to transition in circular micro-tubes testify to the fact that the critical Reynolds number, which corresponds to the onset of such transition, is about 2,000. The evaluation of critical Reynolds number in irregular micro-channels will entail great difficulty since this problem contains a number of characteristic length scales. This fact leads to some vagueness in definition of critical Reynolds number that is not a single criterion, which determines flow characteristics. 

Definitions of flame parameters in channels. D, distance between channel walls effective in flame quenching (quenching distance). D, flame width dead space R, radius of curvature of the flame. 

Alteromonas species producing sodium channel blockers, 80r,82 Anabaena flos-aquae neurotoxins, 88 toxic principle, 108 Analyses, definition, 43 Anatoxin(s) isolation, 88 types, 88,91 Anatoxin a... 

As surface area and pore structure are properties of key importance for any catalyst or support material, we will first describe how these properties can be measured. First, it is useful to draw a clear borderline between roughness and porosity. If most features on a surface are deeper than they are wide, then we call the surface porous (Fig. 5.16). Although it is convenient to think about pores in terms of hollow cylinders, one should realize that pores may have all kinds of shapes. The pore system of zeolites consists of microporous channels and cages, whereas the pores of a silica gel support are formed by the interstices between spheres. Alumina and carbon black, on the other hand, have platelet structures, resulting in slit-shaped pores. All support materials may contain micro, meso and macropores (see text box for definitions). 

There are several major classes of Ca channels (1) receptor-operated Ca channels in plasma membranes (2) ligand-gated Ca " channels in intracellular membranes and (3) voltage-dependent Ca channels that are usually found in plasma membranes or the invaginations of the plasma membrane that are known as transverse tubule membranes. Receptor-dependent or receptor-operated Ca channels (ROCCs) are primarily opened in response to activation of their associated receptors and, by definition, exhibit a certain amount of selectivity for Ca " over other cations. Several potentially different types of ROCCs have been characterized including ATP-sensitive channels in smooth muscle [1], mitogen and IP3-sensitive... 

---