Butenes, cracking

Butene cracks thermally according to, C4H8 = C4H6 + H2, and the reaction is first order, r = kPc4H8 lbmols/liter-hr... 

Secondary butyl alcohol, methylethyl car-binol, 2-butanol, CH3CH2CH(Me)OH. B.p. I00°C. Manufactured from the butane-butene fraction of the gas from the cracking of petroleum. Used to prepare butanone. 

Properly speaking, steam cracking is not a refining process. A key petrochemical process, it has the purpose of producing ethylene, propylene, butadiene, butenes and aromatics (BTX) mainly from light fractions of crude oil (LPG, naphthas), but also from heavy fractions hydrotreated or not (paraffinic vacuum distillates, residue from hydrocracking HOC). 

Methyl /-Butyl Ether. MTBE is produced by reaction of isobutene and methanol on acid ion-exchange resins. The supply of isobutene, obtained from hydrocarbon cracking units or by dehydration of tert-huty alcohol, is limited relative to that of methanol. The cost to produce MTBE from by-product isobutene has been estimated to be between 0.13 to 0.16/L ( 0.50—0.60/gal) (90). Direct production of isobutene by dehydrogenation of isobutane or isomerization of mixed butenes are expensive processes that have seen less commercial use in the United States. 

Aliphatic C-5—C-6. Aliphatic feedstreams are typically composed of C-5 and C-6 paraffins, olefins, and diolefins, the main reactive components being piperylenes cis-[1574-41 -0] and /n j -l,3-pentadiene [2004-70-8f). Other main compounds iaclude substituted C-5 and C-6 olefins such as cyclopentene [142-29-OJ, 2-methyl-2-butene [513-35-9] and 2-methyl-2-pentene [625-27-4J. Isoprene and cyclopentadiene maybe present ia small to moderate quaatities (2—10%). Most steam cracking operatioas are desigaed to remove and purify isoprene from the C-5—C-6 fraction for applications ia mbbers and thermoplastic elastomers. Cyclopentadiene is typically dimerized to dicyclopentadiene (DCPD) and removed from C-5 olefin—diolefin feedstreams duriag fractionation (19). 

Dehydrogenation of Tertiary Amylenes, The staiting material here is a fiaction which is cut from catal57tic clacking of petroleum. Two of the tertiary amylene isomers, 2-methyl-l-butene and 2-methyl-2-butene, are recovered in high purity by formation of methyl tertiary butyl ether and cracking of this to produce primarily 2-methyl-2-butene. The amylenes are mixed with steam and dehydrogenated over a catalyst. The cmde isoprene can be purified by conventional or extractive distillation. 

IFP Process for 1-Butene from Ethylene. 1-Butene is widely used as a comonomer in the production of polyethylene, accounting for over 107,000 t in 1992 and 40% of the total comonomer used. About 60% of the 1-butene produced comes from steam cracking and fluid catalytic cracker effluents (10). This 1-butene is typically produced from by-product raffinate from methyl tert-huty ether production. The recovery of 1-butene from these streams is typically expensive and requires the use of large plants to be economical. Institut Francais du Petrole (IFP) has developed and patented the Alphabutol process which produces 1-butene by selectively dimerizing ethylene. 

Butadiene. Although butadiene was produced in the United States in the eady 1920s, it was not until the start of Wodd War 11 that significant quantities were produced to meet the war effort. A number of processes were investigated as part of the American Synthetic Rubber Program. Catalytic dehydrogenation of / -butenes and / -butanes (Houdry process) and thermal cracking of petroleum hydrocarbons were chosen (12). 

The pattern of commercial production of 1,3-butadiene parallels the overall development of the petrochemical industry. Since its discovery via pyrolysis of various organic materials, butadiene has been manufactured from acetylene as weU as ethanol, both via butanediols (1,3- and 1,4-) as intermediates (see Acetylene-DERIVED chemicals). On a global basis, the importance of these processes has decreased substantially because of the increasing production of butadiene from petroleum sources. China and India stiU convert ethanol to butadiene using the two-step process while Poland and the former USSR use a one-step process (229,230). In the past butadiene also was produced by the dehydrogenation of / -butane and oxydehydrogenation of / -butenes. However, butadiene is now primarily produced as a by-product in the steam cracking of hydrocarbon streams to produce ethylene. Except under market dislocation situations, butadiene is almost exclusively manufactured by this process in the United States, Western Europe, and Japan. 

Butylenes are C Hg mono-olefin isomers 1-butene, <7j -2-butene, trans-2-huX.en.e and isobutylene (2-methylpropene). These isomers are usually coproduced as a mixture and are commonly referred to as the fraction. These fractions are usually obtained as by-products from petroleum refinery and petrochemical complexes that crack petroleum fractions and natural gas Hquids. Since the fractions almost always contain butanes, it is also known as the B—B stream. The linear isomers are referred to as butenes. 

Thermal Cracking. Heavy petroleum fractions such as resid are thermally cracked in delayed cokers or flexicokers (44,56,57). The main products from the process are petroleum coke and off-gas which contain light olefins and butylenes. This stream also contains a considerable amount of butane. Process conditions for the flexicoker are more severe than for the delayed coker, about 550°C versus 450°C. Both are operated at low pressures, around 300—600 kPa (43—87 psi). Flexicokers produce much more linear butenes, particularly 2-butene, than delayed cokers and about half the amount of isobutylene (Table 7). This is attributed to high severity of operation for the flexicoker (43). 

There are currentiy three important processes for the production of isobutylene (/) the extraction process using an acid to separate isobutylene (2) the dehydration of tert-huty alcohol, formed in the Arco s Oxirane process and (3) the cracking of MTBE. The expected demand for MTBE wHl preclude the third route for isobutylene production. Since MTBE is likely to replace tert-huty alcohol as a gasoline additive, the second route could become an important source for isobutylene. Nevertheless, its avaHabHity wHl be limited by the demand for propylene oxide, since it is only a coproduct. An alternative process is emerging that consists of catalyticaHy hydroisomerizing 1-butene to 2-butenes (82). In this process, trace quantities of butadienes are also hydrogenated to yield feedstocks rich in isobutylene which can then be easHy separated from 2-butenes by simple distHlation. 

During World War II, production of butadiene (qv) from ethanol was of great importance. About 60% of the butadiene produced in the United States during that time was obtained by a two-step process utilizing a 3 1 mixture of ethanol and acetaldehyde at atmospheric pressure and a catalyst of tantalum oxide and siHca gel at 325—350°C (393—397). Extensive catalytic studies were reported (398—401) including a fluidized process (402). However, because of later developments in the manufacture of butadiene by the dehydrogenation of butane and butenes, and by naphtha cracking, the use of ethanol as a raw material for this purpose has all but disappeared. 

Butane is primarily used as a fuel gas within the LPG mixture. Like ethane and propane, the main chemical use of butane is as feedstock for steam cracking units for olefin production. Dehydrogenation of n-butane to butenes and to butadiene is an important route for the production of synthetic rubber. n-Butane is also a starting material for acetic acid and maleic anhydride production (Chapter 6). 

Butylenes (butenes) are by-products of refinery cracking processes and steam cracking units for ethylene production. 

Butadiene is obtained mainly as a coproduct with other light olefins from steam cracking units for ethylene production. Other sources of butadiene are the catalytic dehydrogenation of butanes and butenes, and dehydration of 1,4-butanediol. Butadiene is a colorless gas with a mild aromatic odor. Its specific gravity is 0.6211 at 20°C and its boiling temperature is -4.4°C. The U.S. production of butadiene reached 4.1 billion pounds in 1997 and it was the 36th highest-volume chemical. ... 

Propene and 1-butene, respectively, are produced in this free radical reaction. Higher hydrocarbons found in steam cracking products are probably formed through similar reactions. 

The three isomers constituting n-hutenes are 1-hutene, cis-2-hutene, and trans-2-hutene. This gas mixture is usually obtained from the olefinic C4 fraction of catalytic cracking and steam cracking processes after separation of isobutene (Chapter 2). The mixture of isomers may be used directly for reactions that are common for the three isomers and produce the same intermediates and hence the same products. Alternatively, the mixture may be separated into two streams, one constituted of 1-butene and the other of cis-and trans-2-butene mixture. Each stream produces specific chemicals. Approximately 70% of 1-butene is used as a comonomer with ethylene to produce linear low-density polyethylene (LLDPE). Another use of 1-butene is for the synthesis of butylene oxide. The rest is used with the 2-butenes to produce other chemicals. n-Butene could also be isomerized to isobutene. ... 

Butadiene is mainly obtained as a byproduct from the steam cracking of hydrocarbons and from catalytic cracking. These two sources account for over 90% of butadiene demand. The remainder comes from dehydrogenation of n-butane or n-butene streams (Chapter 3). The 1998 U.S. production of butadiene was approximately 4 billion pounds, and it was the 36th highest-volume chemical. Worldwide butadiene capacity was nearly 20 billion pounds. 

Ethylene, propylene, and butene are synthesized industrially by thermal cracking of light (C2-Cg) alkanes. 

Small olefins, notably ethylene (ethene), propene, and butene, form the building blocks of the petrochemical industry. These molecules originate among others from the FCC process, but they are also manufactured by the steam cracking of naphtha. A wealth of reactions is based on olefins. As examples, we discuss here the epoxida-tion of ethylene and the partial oxidation of propylene, as well as the polymerization of ethylene and propylene. 

The alkylation unit in a petroleum refinery is situated downstream of the fluid catalytic cracking (FCC) units. The C4 cut from the FCC unit contains linear butenes, isobutylene, n-butane, and isobutane. In some refineries, isobutylene is converted with methanol into MTBE. A typical modern refinery flow scheme showing the position of the alkylation together with an acid regeneration unit is displayed in Fig. 1. 

In a series of investigations of the cracking of alkanes and alkenes on Y zeolites (74,75), the effect of coke formation on the conversion was examined. The coke that formed was found to exhibit considerable hydride transfer activity. For some time, this activity can compensate for the deactivating effect of the coke. On the basis of dimerization and cracking experiments with labeled 1-butene on zeolite Y (76), it is known that substantial amounts of alkanes are formed, which are saturated by hydride transfer from surface polymers. In both liquid and solid acid catalysts, hydride transfer from isoalkanes larger than... 

With propene, n-butene, and n-pentene, the alkanes formed are propane, n-butane, and n-pentane (plus isopentane), respectively. The production of considerable amounts of light -alkanes is a disadvantage of this reaction route. Furthermore, the yield of the desired alkylate is reduced relative to isobutane and alkene consumption (8). For example, propene alkylation with HF can give more than 15 vol% yield of propane (21). Aluminum chloride-ether complexes also catalyze self-alkylation. However, when acidity is moderated with metal chlorides, the self-alkylation activity is drastically reduced. Intuitively, the formation of isobutylene via proton transfer from an isobutyl cation should be more pronounced at a weaker acidity, but the opposite has been found (92). Other properties besides acidity may contribute to the self-alkylation activity. Earlier publications concerned with zeolites claimed this mechanism to be a source of hydrogen for saturating cracking products or dimerization products (69,93). However, as shown in reaction (10), only the feed alkene will be saturated, and dehydrogenation does not take place. 

---