Ethers, di-n-butyl

Di-n-butyl ether. Technical n-butyl ether does not usually contain appreciable quantities of peroxides, unless it has been stored for a prolonged period. It should, however, be tested for peroxides, and, if the test is positive, the ether should be shaken with an acidified solution of a ferrous salt or with a solution of sodium sulphite (see under Diethyl ether). The ether is dried with anhydrous calcium chloride, and distilled through a fractionating column the portion, b.p. 140-141°, is collected. If a fraction of low boiling point is obtained, the presence of n-butyl... 

Prepare a Grignard reagent from 24 -5 g. of magnesium turnings, 179 g. (157 ml.) of n-heptyl bromide (Section 111,37), and 300 ml. of di-n-butyl ether (1). Cool the solution to 0° and, with vigorous stirring, add an excess of ethylene oxide. Maintain the temperature at 0° for 1 hour after the ethylene oxide has been introduced, then allow the temperature to rise to 40° and maintain the mixture at this temperature for 1 hour. Finally heat the mixture on a water bath for 2 hours. Decompose the addition product and isolate the alcohol according to the procedure for n-hexyl alcohol (Section 111,18) the addition of benzene is unnecessary. Collect the n-nonyl alcohol at 95-100°/12 mm. The yield is 95 g. 

The preparation of diethyl ether is described here for the sake of completeness. It is an unsuitable exercise for beginners. Di-n-butyl ether (Section 111,57) offers an excellent alternative. 

An alternative method for isolating the n-butyl ether utilises the fact that n-butyl alcohol is soluble in saturated calcium chloride solution whilst n-butyl ether is slightly soluble. Cool the reaction mixture in ice and transfer to a separatory fimnel. Wash cautiously with 100 ml. of 2-5-3N sodium hydroxide solution the washings should be alkaline to litmus. Then wash with 30 ml. of water, followed by 30 ml. of saturated calcium chloride solution. Dry with 2-3 g. of anhydrous calcium chloride, filter and distil. Collect the di-n-butyl ether at 139-142°. The yield is 20 g. 

If, however, the water formed is removed as formed (compare the preparation of di-n-butyl ether. Section 111,57), the sulphuric acid may react completely and the method may be employed for the preparation of the free sulphonic acid. 

Separations based upon differences in the chemical properties of the components. Thus a mixture of toluene and anihne may be separated by extraction with dilute hydrochloric acid the aniline passes into the aqueous layer in the form of the salt, anihne hydrochloride, and may be recovered by neutralisation. Similarly, a mixture of phenol and toluene may be separated by treatment with dilute sodium hydroxide. The above examples are, of comse, simple apphcations of the fact that the various components fah into different solubihty groups (compare Section XI,5). Another example is the separation of a mixture of di-n-butyl ether and chlorobenzene concentrated sulphuric acid dissolves only the w-butyl other and it may be recovered from solution by dilution with water. With some classes of compounds, e.g., unsaturated compounds, concentrated sulphuric acid leads to polymerisation, sulphona-tion, etc., so that the original component cannot be recovered unchanged this solvent, therefore, possesses hmited apphcation. Phenols may be separated from acids (for example, o-cresol from benzoic acid) by a dilute solution of sodium bicarbonate the weakly acidic phenols (and also enols) are not converted into salts by this reagent and may be removed by ether extraction or by other means the acids pass into solution as the sodium salts and may be recovered after acidification. Aldehydes, e.g., benzaldehyde, may be separated from liquid hydrocarbons and other neutral, water-insoluble hquid compounds by shaking with a solution of sodium bisulphite the aldehyde forms a sohd bisulphite compound, which may be filtered off and decomposed with dilute acid or with sodium bicarbonate solution in order to recover the aldehyde. 

NC13, mw 120.38, N 11.64% yel, vol, pungent-smelling oil, mp <-40° (Porret in 1813 reported —27°), bp about 71° (explds at 93-95°), d 1.653g/cc. Sol in cold w (decompd by hot w), ale, eth, chlf, bz, CCl CS2 phosphorous oxychloride. Prepd (with great care) by the action of sodium hypochlorite on amm chloride. The compd also forms at the anode in the electrolysis of coned amm chioride soln. Another prepn consists of bubbling chlorine into a cooled aq soln of amm sulfate di-n-butyl ether (Refs 1,... 

J. B. Ott, K. N. Marsh, and A. E. Richards, "Excess Enthalpies, Excess Gibbs Free Energies, and Excess Volumes for (di-//-Butyl Ether-)- Benzene) and Excess Gibbs Free Energies and Excess Volumes for (di-n-Butyl Ether + Tetrachloromethane) at 298.15 and 308.15 K", /. Chem. Thermodyn., 13, 447-455 (1981). 

Ethers. Di-n-butyl ether Anisole Diphenyl ether. 

Ethers are unaffected by sodium and by acetyl (or benzoyl) chloride. Both the purely aliphatic ethers e.g., di-n-butyl ether (C4H, )30 and the mixed aliphatic - aromatic ethers (e.g., anisole C3HSOCH3) are encountered in Solubility Group V the purely aromatic ethers e.g., diphenyl ether (C,Hj)20 are generally insoluble in concentrated sulphuric acid and are found in Solubility Group VI. The purely aliphatic ethers are very inert and their final identification may, of necessity, depend upon their physical properties (b.p., density and/or refractive index). Ethers do, however, suffer fission when heated with excess of 67 per cent, hydriodic acid, but the reaction is generally only of value for the characterisation of symmetrical ethers (R = R ) ... 

Di-n-butyl ether (111,57, scale use 100 ml. Pyrex bolt-head flask). 

---