Analytical methods control

Like most electro-analytical methods controlled-potential coul-ometry appears deceptively simple in principle, but requires some understanding of possible experimental complications and skill in the interpretation of data in order to be used effectively and with confidence. Fortunately, this technique does not stand by itself but is closely related to, and can draw heavily on, the more familiar electro-analytical fields of potentiometry and amperometry. 

When designing and evaluating an analytical method, we usually make three separate considerations of experimental error. First, before beginning an analysis, errors associated with each measurement are evaluated to ensure that their cumulative effect will not limit the utility of the analysis. Errors known or believed to affect the result can then be minimized. Second, during the analysis the measurement process is monitored, ensuring that it remains under control. Finally, at the end of the analysis the quality of the measurements and the result are evaluated and compared with the original design criteria. This chapter is an introduction to the sources and evaluation of errors in analytical measurements, the effect of measurement error on the result of an analysis, and the statistical analysis of data. 

The largest division of interfacial electrochemical methods is the group of dynamic methods, in which current flows and concentrations change as the result of a redox reaction. Dynamic methods are further subdivided by whether we choose to control the current or the potential. In controlled-current coulometry, which is covered in Section IIC, we completely oxidize or reduce the analyte by passing a fixed current through the analytical solution. Controlled-potential methods are subdivided further into controlled-potential coulometry and amperometry, in which a constant potential is applied during the analysis, and voltammetry, in which the potential is systematically varied. Controlled-potential coulometry is discussed in Section IIC, and amperometry and voltammetry are discussed in Section IID. 

Minimizing Electrolysis Time The current-time curve for controlled-potential coulometry in Figure 11.20 shows that the current decreases continuously throughout electrolysis. An exhaustive electrolysis, therefore, may require a long time. Since time is an important consideration in choosing and designing analytical methods, the factors that determine the analysis time need to be considered. 

Controllcd-Currcnt Coulomctry The use of a mediator makes controlled-current coulometry a more versatile analytical method than controlled-potential coulome-try. For example, the direct oxidation or reduction of a protein at the working electrode in controlled-potential coulometry is difficult if the protein s active redox site lies deep within its structure. The controlled-current coulometric analysis of the protein is made possible, however, by coupling its oxidation or reduction to a mediator that is reduced or oxidized at the working electrode. Controlled-current coulometric methods have been developed for many of the same analytes that may be determined by conventional redox titrimetry. These methods, several of which are summarized in Table 11.9, also are called coulometric redox titrations. 

Scale of Operation Coulometric methods of analysis can be used to analyze small absolute amounts of analyte. In controlled-current coulometry, for example, the moles of analyte consumed during an exhaustive electrolysis is given by equation 11.32. An electrolysis carried out with a constant current of 100 pA for 100 s, therefore, consumes only 1 X 10 mol of analyte if = 1. For an analyte with a molecular weight of 100 g/mol, 1 X 10 mol corresponds to only 10 pg. The concentration of analyte in the electrochemical cell, however, must be sufficient to allow an accurate determination of the end point. When using visual end points, coulometric titrations require solution concentrations greater than 10 M and, as with conventional titrations, are limited to major and minor analytes. A coulometric titration to a preset potentiometric end point is feasible even with solution concentrations of 10 M, making possible the analysis of trace analytes. 

An important step in developing a standard method is to determine which factors have a pronounced effect on the quality of the analytical method s result. The procedure can then be written to specify the degree to which these factors must be controlled. A procedure that, when carefully followed, produces high-quality results in different laboratories is considered rugged. The method by which the critical factors are discovered is called ruggedness testing. ... 

A final component of a quality control program is the certification of an analyst s competence to perform the analysis for which he or she is responsible. Before an analyst is allowed to perform a new analytical method, he or she may be required to successfully analyze an independent check sample with acceptable accuracy and precision. The check sample should be similar in composition to samples that the analyst will routinely encounter, with a concentration that is 5 to 50 times that of the method s detection limit. 

Finally, the textbook concludes with two chapters discussing the design and maintenance of analytical methods, two topics of importance to analytical chemists. Chapter 14 considers the development of an analytical method, including its optimization, verification, and validation. Quality control and quality assessment are discussed in Chapter 15. 

The EPA publishes Series Methods that describe the exact procedures to be followed with respect to sample receipt and handling, analytical methods, data reporting, and document control. These guidelines must be followed closely to ensure accuracy, reproducibility, and reliability within and among the contract laboratories. 

Analytical and control methods for acetic anhydride are fully discussed in reference 55. Performance tests are customarily used where the quality of the product is cmcial, as in food or pharmaceutical products. Typical specifications are ... 

Another quaHty control problem of multipurpose plants is the clean out for a product change. A test for residual cleaning solvents in the ppm level is a necessity. The best vaHdation of the cleaning process is to develop an analytical method that is able to find the previous product in the new product at a level of not more than 1 ppm. Tests should be mn on at least the first three batches. 

Eor purposes of product identification and quaUty control it is useful not only to employ the abovementioned analytical methods but also to measure physical constants such as the density, refractive index, melting point, and pH value of the material. 

Scientific Apparatus Makers Association 1140 Coimecticut Avenue, NW Washington, D.C. 20036 Standards for analytical instmments, laboratory apparatus, measurement and test instmments, nuclear instmments, optical instmments, process measurement and control, and scientific laboratory furniture and equipment (see Analytical methods). 

Analytical Methods. Molybdenum contents in ore concentrates and technical oxide are most accurately deterrnined gravimetricaHy by precipitating lead molybdate. Molybdenum content is usually not determined on pure compounds or metal. Instead, spectrographic methods are used to measure impurity elements that must be controlled. Carbon and oxygen in metal products are measured by standard gas analysis methods. 

Analytical methods iaclude thin-layer chromatography (69), gas chromatography (70), and specific methods for determining amine oxides ia detergeats (71) and foods (72). Nuclear magnetic resonance (73—75) and mass spectrometry (76) have also been used. A frequentiy used procedure for iadustrial amine oxides (77) iavolves titratioa with hydrochloric acid before and after conversion of the amine to the quaternary ammonium salt by reaction with methyl iodide. A simple, rapid quaHty control procedure has been developed for the deterrniaation of amine oxide and unreacted tertiary amine (78). 

The objective ia any analytical procedure is to determine the composition of the sample (speciation) and the amounts of different species present (quantification). Spectroscopic techniques can both identify and quantify ia a single measurement. A wide range of compounds can be detected with high specificity, even ia multicomponent mixtures. Many spectroscopic methods are noninvasive, involving no sample collection, pretreatment, or contamination (see Nondestructive evaluation). Because only optical access to the sample is needed, instmments can be remotely situated for environmental and process monitoring (see Analytical METHODS Process control). Spectroscopy provides rapid real-time results, and is easily adaptable to continuous long-term monitoring. Spectra also carry information on sample conditions such as temperature and pressure. 

Terpene chemists use mainly gas chromatography in dealing with terpene mixtures in research and development as weU as in quahty control. Capillary gas chromatography with stable bonded-phase columns, the primary analytical method, is also being used more frequendy in the 1990s in product quahty control because its greater resolution is helpful in producing consistent products. 

Operations capable of generating airborne beryUium particulate, such as melting, machining, welding, grinding, etc, are effectively controUed by local exhaust ventilation or other control measures. To assure a safe environment and measure compliance with the OSHA standards, employee exposures should be periodicaUy measured by prescribed air sampling and analytical methods. 

The other analytical methods necessary to control the typical specification given in Table 5 are, for the most part, common quality-control procedures. When a chemical analysis for purity is desired, acetylation or phthalation procedures are commonly employed. In these cases, the alcohol reacts with a measured volume of either acetic or phthalic anhydride in pyridine solution. The loss in titratable acidity in the anhydride solution is a direct measure of the hydroxyl groups reacting in the sample. These procedures are generally free from interference by other functional groups, but both are affected adversely by the presence of excessive water, as this depletes the anhydride reagent strength to a level below that necessary to ensure complete reaction with the alcohol. Both procedures can be adapted to a semimicro- or even microscale deterrnination. 

The complex of the following destmctive and nondestmctive analytical methods was used for studying the composition of sponges inductively coupled plasma mass-spectrometry (ICP-MS), X-ray fluorescence (XRF), electron probe microanalysis (EPMA), and atomic absorption spectrometry (AAS). Techniques of sample preparation were developed for each method and their metrological characteristics were defined. Relative standard deviations for all the elements did not exceed 0.25 within detection limit. The accuracy of techniques elaborated was checked with the method of additions and control methods of analysis. 

The analysis was performed by XRF method with SR. SRXRF is an instrumental, multielemental, non-destructive analytical method using synchrotron radiation as primary excitation source. The fluorescence radiation was measured on the XRF beam-line of VEPP-3 (E=2 GeV, 1=100 mA), Institute of Nuclear Physics, Novosibirsk, Russia. For quality control were used international reference standards. 

Process Hazards Analysis (PrHA) - The application of analytical methods to identify and evaluate process hazards to determine the adequacy or control. 

The specification development process is a data-driven activity that requires a validated analytical method. The levels of data needed include assay precision, replicate process results (process precision), and real-time stability profiles. A statistical analysis of these data is critical in setting a realistic specification. Most often, aggregation and fragmentation degradation mechanisms are common to protein and peptide therapeutics. Therefore, the SE-HPLC method provides a critical quality parameter that would need to be controlled by a specification limit. 

Exploitation of analytical selectivity. We have seen, in our discussion of the A —> B C series reaction (Scheme IX), that access to the concentration of A as a function of time is valuable because it permits to be easily evaluated. Modern analytical methods, particularly chromatography, constitute a powerful adjunct to kinetic investigations, and they render nearly obsolete some very difficult kinetic problems. For example, the freedom to make use of the pseudoorder technique is largely dependent upon the high sensitivity of analytical methods, which allows us to set one reactant concentration much lower than another. An interesting example of analytical control in the study of the Scheme IX system is the spectrophotometric observation of the reaction solution at an isosbestic point of species B and C, thus permitting the A to B step to be observed. 

The guideline states that the objective of validation is to demonstrate that an analytical method is fit for its purpose and summarizes the characteristics required of tests for identification, control of impurities and assay procedures (Table 13-2). As such, it applies to chiral drug substances as to any other active ingredients. Requirements for other analytical procedures may be added in due course. 

Training courses are available in analytical methods of fault-tracing. Computers are also in use which monitor a number of parameters and draw attention to any observed abnormality. The control/ monitoring device may then make a judgement as to the cause, or this may rely on the interpretation of the operator. Considerable use is now made of logic control/monitoring devices which can oversee the operation of a large number of installations from a central computer/observation terminal. 

---