Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Analytical methods conductivity

Analytical Methods. Conductivity Measurements. Conductivity was measured on ElectroMark Analyzer Model 4402. Triplicate readings were taken on each of the Dl-Ca waters. [Pg.68]

For each test or control article that is mixed with a carrier, are tests by appropriate analytical methods conducted ... [Pg.186]

However, online alternatives developed for environmental analysis are commonly direct adaptations of traditional analytical methods conducted in batch. Main limitations for most of these methods are sensitivity or precision problems due to the low concentrations of the individual species to be analyzed... [Pg.177]

It should be emphasized that adding at least one species of each lipid class of interest prior to extraction to serve as an internal standard is very important for the sake of quantitative analysis. Any incomplete recovery could be compensated for with the internal standard(s) to a certain degree since any differential extraction efficiency of individual species in a class from that of the standard is largely a matter of secondary effect. However, for any analytical method conducted based on external standards, a complete recovery of extraction of a lipid class of interest is essential for accurate quantification. [Pg.90]

The evaluation phase of industrial hygiene is the process of making measurements on some set of samples which permits a conclusion about the degrees of hazard. Before conducting an evaluation, it is necessary to make a number of choices of what and where to sample, when to sample, how long to sample, how many samples to take, what sampling and analytical methods to use, what exposure criteria to use in the analysis of the data, and how to report the results. These choices as a whole constitute the evaluation plan. The object is to find if one or more workers have an unacceptable probabiUty of being exposed in excess of some estabUshed limit. [Pg.106]

The Reich test is used to estimate sulfur dioxide content of a gas by measuring the volume of gas required to decolorize a standard iodine solution (274). Equipment has been developed commercially for continuous monitoring of stack gas by measuring the near-ultraviolet absorption bands of sulfur dioxide (275—277). The deterrnination of sulfur dioxide in food is conducted by distilling the sulfur dioxide from the acidulated sample into a solution of hydrogen peroxide, foUowed by acidimetric titration of the sulfuric acid thus produced (278). Analytical methods for sulfur dioxide have been reviewed (279). [Pg.147]

It is often experimentally convenient to use an analytical method that provides an instrumental signal that is proportional to concentration, rather than providing an absolute concentration, and such methods readily yield the ratio clc°. Solution absorbance, fluorescence intensity, and conductance are examples of this type of instrument response. The requirements are that the reactants and products both give a signal that is directly proportional to their concentrations and that there be an experimentally usable change in the observed property as the reactants are transformed into the products. We take absorption spectroscopy as an example, so that Beer s law is the functional relationship between absorbance and concentration. Let A be the reactant and Z the product. We then require that Ea ez, where e signifies a molar absorptivity. As initial conditions (t = 0) we set Ca = ca and cz = 0. The mass balance relationship Eq. (2-47) relates Ca and cz, where c is the product concentration at infinity time, that is, when the reaction is essentially complete. [Pg.34]

Information on ship resistance has been determined from large numbers of tests on scale models of ships and from full-size ships, and compilations of these experimental results have been published. For a new and innovative hull form the usual procedure is to construct a scale model of the ship and then to conduct resistance tests m a special test facility (towing tank). Alternatively, analytical methods can provide estimates of ship resistance for a range of different hull shapes. Computer programs have been written based on these theoretical analyses and have been used with success for many ship designs, including racing sailboats. [Pg.1043]

These conceptual goals are attained by several combinatorial methods and tools. Characteristic for combinatorial chemistry is the synthesis on solid support or by polymer-supported synthesis, allowing for much higher efficiency in library production. Synthesis can be conducted either in automated parallel synthesis or by split-and-recombine synthesis. Centerpieces of combinatorial methods further include specific analytical methods for combinatorial... [Pg.381]

A variety of studies can be found in the literature for the solution of the convection heat transfer problem in micro-channels. Some of the analytical methods are very powerful, computationally very fast, and provide highly accurate results. Usually, their application is shown only for those channels and thermal boundary conditions for which solutions already exist, such as circular tube and parallel plates for constant heat flux or constant temperature thermal boundary conditions. The majority of experimental investigations are carried out under other thermal boundary conditions (e.g., experiments in rectangular and trapezoidal channels were conducted with heating only the bottom and/or the top of the channel). These experiments should be compared to solutions obtained for a given channel geometry at the same thermal boundary conditions. Results obtained in devices that are built up from a number of parallel micro-channels should account for heat flux and temperature distribution not only due to heat conduction in the streamwise direction but also conduction across the experimental set-up, and new computational models should be elaborated to compare the measurements with theory. [Pg.187]

The objectives of this presentation are to discuss the general behavior of non isothermal chain-addition polymerizations and copolymerizations and to propose dimensionless criteria for estimating non isothermal reactor performance, in particular thermal runaway and instability, and its effect upon polymer properties. Most of the results presented are based upon work (i"8), both theoretical and experimental, conducted in the author s laboratories at Stevens Institute of Technology. Analytical methods include a Semenov-type theoretical approach (1,2,9) as well as computer simulations similar to those used by Barkelew LS) ... [Pg.15]

Andrea Manca is Research Fellow at the Centre for Health Economics, University of York. His research interests lie in the investigation of methodological and theoretical issues related to two broad areas the application of modelling techniques to support the decisionmaking process in health care, and the use of analytical methods in the conduction of economic analysis of health care interventions. Andrea s applied work focuses on a number of different technologies in several clinical areas, including mental health. [Pg.118]

A review is presented here of certification approaches, followed by several of the major agencies and individual developers of RMs for chemical composition, addressing some of the many associated scientific aspects that significantly impinge on the conduct and outcome of the analytical characterization exercises. These include definition of analytical methods selection of analytical methodologies, analysts and laboratories in-house characterization and cooperative inter-laboratory characterization. [Pg.50]

Reviews and checks out analytical methods for pesticides submitted by registrants Monitors residues in imported and domestic food, including processed food Monitors residues in meat and poultry Conducts market basket surveys Monitors pesticides in fish and wildlife... [Pg.8]

The evaluation of all NADA analytical methods was previously conducted exclusively by the CVM. Since 1995, the CVM has offered sponsors of NADA residue methods the option of conducting the method trial through a Sponsor Monitored Method Trial (SMMT) process. The SMMT is conducted according to CVM specifications with CVM oversight. The resultant performance data must be reviewed and judged acceptable by CVM before the method is approved. [Pg.90]

Until 1991, manufacturers seeking authorizations for pesticides had to fulfil country-specific requirements of validation of enforcement methods. The term enforcement method means analytical methods which are developed for post-registration control and monitoring purposes. The harmonization of these requirements was initiated with the European Economic Community (EEC) Council Directive 91/414/EEC and temporarily finalized with the Guidance Document on Residue Analytical Methods SANCO/825/00 rev. 6, dated 20 June 2000 [Santd et Protection des Consommateurs (SANCO)]. The evaluation of validation studies by the competent authority is conducted by comparison of these European Union (EU) requirements with the study results and most often without any practical experience of the method. Some details of this evaluation are discussed below. [Pg.96]

Even if most examples and procedures presented apply to in-house validation, the procedure does not distinguish between validations conducted in a single laboratory and those carried out within inter-laboratory method performance studies. A preference for inter-laboratory studies can be concluded from the statement that laboratories should always give priority to methods which have been tested in method performance studies. Within the procedure a profound overview of different categories of analytical methods according to the available documentation and previous external validation is given. For example, if a method is externally validated in a method performance study, it should be tested for trueness and precision only. On the other hand, a full validation is recommended for those methods which are published in the scientific literature without complete presentation of essential performance characteristics (Table 9). [Pg.121]

When developing or routinely using an analytical method, quality control (QC) fortifications can be added to each sample at critical points in the procedure to ensure that sensitive steps in the method were conducted properly and to pinpoint where problems occurred if results are less than satisfactory. For example, if the QC fortification samples for detection and cleanup were to show acceptable results in a batch of samples, but the extraction QC spike gave low recovery and/or high variability, then the analyst could modify instrument conditions or altering cleanup parameters immediately. Likewise, if the QC spike added just before analysis gives poor results, then instrument maintenance could be done and the samples merely re-analyzed rather than re-extracted. [Pg.754]


See other pages where Analytical methods conductivity is mentioned: [Pg.174]    [Pg.687]    [Pg.812]    [Pg.146]    [Pg.266]    [Pg.214]    [Pg.33]    [Pg.106]    [Pg.708]    [Pg.153]    [Pg.425]    [Pg.436]    [Pg.536]    [Pg.622]    [Pg.871]    [Pg.130]    [Pg.299]    [Pg.62]    [Pg.149]    [Pg.298]    [Pg.7]    [Pg.20]    [Pg.24]    [Pg.49]    [Pg.109]    [Pg.232]    [Pg.409]    [Pg.566]    [Pg.603]    [Pg.608]    [Pg.608]    [Pg.612]    [Pg.652]   
See also in sourсe #XX -- [ Pg.85 ]




SEARCH



Conductivity Method

© 2024 chempedia.info