Thermoplastic reinforced elastomer

TRE thermoplastic reinforced elastomer ent locations such as Lowell, UM-L)... 

Important are behaviors associated and interrelated with plastic materials (thermoplastics, thermosets, elastomers, reinforced plastics, etc.) and fabricating processes (extrusion, injection molding, blow molding, forming, foaming, reaction injection molding, etc.). They are presented so that the technical or non-technical reader can readily understand the interrelationships. 

DSM Engineering Plastics, nylon, PBT, Polycarbonate Thermoplastic Elastomer PC/ABS Conductive Resins Thermoplastics Reinforced and Filled Thermoplastics Lubricated... 

Uniaxial deformations give prolate (needle-shaped) ellipsoids, and biaxial deformations give oblate (disc-shaped) ellipsoids [220,221], Prolate particles can be thought of as a conceptual bridge between the roughly spherical particles used to reinforce elastomers and the long fibers frequently used for this purpose in thermoplastics and thermosets. Similarly, oblate particles can be considered as analogues of the much-studied clay platelets used to reinforce a variety of materials [70-73], but with dimensions that are controllable. In the case of non-spherical particles, their orientations are also of considerable importance. One interest here is the anisotropic reinforcements such particles provide, and there have been simulations to better understand the mechanical properties of such composites [86,222],... 

The methods used to increase the water resistance of a glass microsphere foam are basically those applied to glass-reinforced plastics, filled thermoplasts, and elastomers, viz. hydrophobic adhesion compounds are added to binder and microsphere dressing 147). The compounds added are alkyl alkoxysilane derivatives, amino or epoxy alkoxysilanes for epoxy and phenolic resins, vinyl or methacryloxy alkoxysilanes for polyester resins. The dressing agents used are aminoethoxysilanes (y-aminopropyl-... 

Kevlar pulp can be used in thermosets, thermoplastics and elastomers. Injection-moldable pellets consisting of short Kevlar fibers in a thermoplastic resin can be made These can be blended with unreinforced resins to obtain a composite with the desired volume fraction of reinforcement. 

The impact strength of brittle thermoplastic materials is generally improved by adding small amounts of rubber, either pure or modified by grafting with the monomer or monomers constituting the matrix to be reinforced (1, 2, 3, 4, 5). As a rule, modification is achieved by monomer polymerization in the presence of the reinforcing elastomer, which is usually a butadiene polymer or copolymer (6, 7). 

For a variety of technical reasons the development of aromatic polyamides was much slower in comparison. Commercially introduced in 1961, the aromatic polyamides have expanded the maximum temperature well above 200°C. High-tenacity, high-modulus polyamide fibers (aramid fibers) have provided new levels of properties ideally suited for tire reinforcement. More recently there has been considerable interest in some new aromatic glassy polymers, in thermoplastic polyamide elastomers, and in a variety of other novel materials. 

Polypropylene (PP) in various forms (filled, unfilled, reinforced, rubber blended) finds the greatest usage of all automotive plastics. Its consumption is likely to accelerate as a result of new laws requiring recyclability, and because of the weight and cost reductions it offers. New fabrication techniques may also contribute to growth. For example, the monomaterial sandwich construction techniques developed by fabricators yield rugged and lightweight PP-based instrument and door panels. These parts consist of a sandwich of reinforced or neat PP substrate, a cross-linked PP foam, and a thermoplastic polyolefin elastomer (TPO) cover. 

S. Saikrasun and T. Amomsakchai. Phase behavior and properties of in situ-reinforcing elastomer composites based on thermoplastic elastomers and thermotropic liquid crystalline copolyester. J. Appl. Polym. ScL, 101 1610-1619, 2006. 

Plastics (thermoplastics, duroplastics, elastomers) have been reinforced for decades to enhance mainly mechanical properties with fibers (glass, carbon, aramide, metal, ceramic, natural). 

With both the PEA/P(S-co-MMA) and PB/PS IPN s, an important variable is the ratio of elastomer to plastic in the final material. When the plastic component predominates, a type of impact-resistant plastic results. In this manner the PB/PS IPN s are analogous to the impact-resistant graft copolymers. When the elastomer component predominates, a self-reinforced elastomer results, the behavior resembling that of the ABA-type block copolymers (thermoplastic elastomers) described in Section 4.4. When the overall compositions of both the PB/PS and the PEA/P(S-co-MMA) series are close to 50/50, the materials behave like leathers. 

It is of interest to compare the mechanical behavior of these model reinforced elastomers with the thermoplastic elastomers discussed in the... 

Impact-resistant properties, especially at low temperatures, low-temperature toughness, melt-processing properties, and dimensional stability of thermoplastic polyurethane elastomers are improved by the addition of a carbonyl-modified polyolefin [54,55]. These improvements are particularly useful for reinforced polyurethanes. Small amounts of polyolefin homopolymer or copolymer with TPU blends are useful for molding plastic articles by injection molding, extrusion, calendering, or similar process for molding thermoplastic articles [56]. 

Rigid polyvinyl chloride Polyphenylene sulfide Thermoplastic urethane elastomers Many reinforced plastics... 

Description For glass-reinforced thermosetting resins modified particle shapes offer choices of higher loadings, better processing (lower viscosity) and physical properties, smoother finish. Superfine grades for thermoplastic and elastomer cable compounds and mouldings ... 

In reinforced plastics various inorganic materials are dispersed in the polymer. Carbon black reinforced elastomers have already been considered see Section 9.16.2. For fiber composites, two subtypes are important, the short fiber-containing materials, which are thermoplastic, and the continuous filament types, which cannot flow. While short fibers can be melt blended with thermoplastics, they are often embedded in monomeric mixes, followed by polymerization in situ. Continuous fibers are always processed via monomeric mixes which can flow over the beds of fibers. Of course, these monomeric mixes may have polymers or prepolymers dissolved in them, raising the viscosity, and reducing shrinkage on polymerization. An example of the continuous filament type is a tape composite, familiar as the strapping tape used for packaging. 

The triblock copolymer thermoplastic elastomers serve as interesting examples. One of the enormous advantages of these materials is that they "crosslink on cooling from the melt to form self-reinforced elastomers. However, because the physical... 

Automotive and electrical/electronics industries are the largest markets for engineering polymers which include Crastin PBT polyesters, Hytrel thermoplastic polyester elastomers, Rynite PET, high-temperature Thermx PCT (polycyclohexylene dimethyl terephthalate), Tribon composites and Tynex filaments, Vespel polyimide parts and shapes, Zenite liquid crystal polymers and Zytel PA resins. In July 2005, DuPont launched the DuPont Vespel SP-202 composition whose properties include the prevention of static charge build-up. Other products include Delrin acetal resins, engineering thermoplastic vulcanisates. Minion mineral reinforced PA resins and Teflon PTFE fluoropolymer resins. 

This handbook provides information related principally to families of thermoplastics reinforced with strand E glass. The handbook content, while limited to molding materials, advises the reader that other forms of thermoplastic materials —such as foams and elastomers —are also glass reinforced. 

---