Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Hydrophobic adhesives

Rowell, R.M., Youngquist, J.A. and Sachs, LB. (1987a). Adhesive bonding of acetylated aspen flakes, part 1. Surface changes, hydrophobicity, adhesive penetration and strength. International Journal of Adhesion and Adhesives, 7(4), 183-188. [Pg.223]

The methods used to increase the water resistance of a glass microsphere foam are basically those applied to glass-reinforced plastics, filled thermoplasts, and elastomers, viz. hydrophobic adhesion compounds are added to binder and microsphere dressing 147). The compounds added are alkyl alkoxysilane derivatives, amino or epoxy alkoxysilanes for epoxy and phenolic resins, vinyl or methacryloxy alkoxysilanes for polyester resins. The dressing agents used are aminoethoxysilanes (y-aminopropyl-... [Pg.98]

Fluoroepoxy resins have also been developed that when cured with silicone amines or fluoroanhydrides show substantial hydrophobicity. As the resin s fluorocarbon content is increased, so is the hydrophobicity. Adhesives made with these compounds showed much... [Pg.134]

It is more satisfactory to choose an essentially hydrophobic adhesive in which water is only sparingly soluble and which has a low diffusion coefficient, and this was the approach chosen by the Admiralty Research Establishment when researching in this area. ... [Pg.565]

Very high frictional forces between sliding contacts of two PDMS surfaces in an aqueous environment [Fig. 5(A)] are ascribed to the strong hydrophobic adhesive forces, and surface-grafted PEG chains on PDMS surface are known to provide surface... [Pg.425]

Interaction of Solids With Flotation Reagents. For flotation to occur with the aid of reagents, such compounds must adsorb at the sohd—hquid interface unless the soHd to be floated is naturally hydrophobic. In this latter case only depression can be attempted by the use of additional ions or depressants that hinder bubble—particle adhesion. Frothers (typically long-chain alcohols) and/or modifying agents such as hydrocarbon oils can, however, be used to enhance the collection of naturally hydrophobic soflds such as M0S2, talc, or plastics. [Pg.48]

The phenoHc resins used for particle board are NaOH-catalyzed resoles of low viscosity and high water miscibility, similar to the Hquid resole adhesives used in plywood manufacture. The higher resin and caustic content of the board frequently necessitates the addition of hydrophobic agents such as wax emulsions to increase the barrier properties of the board. The adhesive is appHed to the particles in thin streams using high agitation to maximize material usage. Boards are cured in presses for 5—10 min at 150—185°C. [Pg.306]

Oxane bonds, M—O—Si, are hydroly2ed during prolonged exposure to water but reform when dried. Adhesion in composites is maintained by controlling conditions favorable for equiUbrium oxane formation, ie, maximum initial oxane bonding, minimum penetration of water to the interface, and optimum morphology for retention of silanols at the interface. The inclusion of a hydrophobic silane, such as phenyltrimethoxysilane [2996-92-17, with the organofunctional silane increases thermal stabiUty of the silane and make the bond more water resistant (42). [Pg.74]

Increased flexibility Increased dispersing power Increased water sensitivity Increased adhesion to hydrophobic surfaces... [Pg.475]

The flotation process usually iuvolves three steps (/) the conditioning of the coal surface iu a slurry with reagents, (2) adhesion of hydrophobic coal particles to gas bubbles, and (J) the separation of the coal-laden bubbles from the slurry. In the conventional flotation process, when the coal particles become attached to air bubbles, the particles ate allowed to rise to the top of the flotation cell and form a stable froth layer (9). A mechanical scraper is used to remove the froth layer and separate the clean coal product from the refuse-laden slurry. [Pg.254]

Most molded plastics have a very smooth, hydrophobic surface that must be modified. Chemical etchants are used to oxidize and roughen the surface. The resultant hydrophilic surface promotes good metal-to-plastic adhesion. The etchant is usually a solution of chromic acid and sulfuric acid pure chromic acid can also be used. [Pg.109]

Polyurethane dispersions (PUD s) are usually high-performance adhesives based on crystalline, hydrophobic polyester polyols, such as hexamethylene adipate, and aliphatic diisocyanates, such as methylene bis(cyclohexyl isocyanate) (H12MDI) or isophorone diisocyanate (IPDI). These PUD s are at the more expensive end of the waterborne adhesive market but provide excellent performance. [Pg.788]

All of the eommereial alkyl eyanoaerylate monomers are low-viseosity liquids, and for some applications this can be an advantage. However, there are instances where a viseous liquid or a gel adhesive would be preferred, sueh as for application to a vertical surface or on porous substrates. A variety of viscosity control agents, depending upon the desired properties, have been added to increase the viscosity of instant adhesives [21]. The materials, which have been utilized, include polymethyl methacrylate, hydrophobic silica, hydrophobic alumina, treated quartz, polyethyl cyanoacrylate, cellulose esters, polycarbonates, and carbon black. For example, the addition of 5-10% of amorphous, non-crystalline, fumed silica to ethyl cyanoacrylate changes the monomer viscosity from a 2-cps liquid to a gelled material [22]. Because of the sensitivity of cyanoacrylate esters to basic materials, some additives require treatment with an acid to prevent premature gelation of the product. [Pg.856]

The contact angles of water and adhesive resin on wood are higher in the case of freshly harvested wood compared to stored chips. This means that the surface of particles from this fresh wood is more hydrophobic. This influences the wetting and the penetration negatively and with this the gluability. Reason for this lower wettability of freshly harvested wood is a higher content of some wood chemical components, or wood extractives, as has been determined by water extraction. This result, however, must not be confused with the better wettability of a freshly cut surface, independently if it is freshly harvested or stored wood. [Pg.1084]

To check the efficacy of grease removal, the alkali solution is rinsed away or neutralised by dipping in dilute acid. If, after removal from the acid, the draining metal surface remains wetted evenly all over for 30-60 s (or until it dries by evaporation), hydrophobic soils have been removed. Traces of grease cause the surface to de-wet, and surface tension draws the water into separate droplets. This is the water-break test. Traces of grease which remain when the work is plated do not prevent electrodeposition, but are detrimental to adhesion and corrosion resistance. [Pg.337]

The results of mechanical properties (presented later in this section) showed that up to 20 phr, the biofillers showed superior strength and elongation behavior than CB, cellulose being the best. After 30 phr the mechanical properties of biocomposites deteriorated because of the poor compatibility of hydrophilic biopolymers with hydrophobic natural rubber(results not shown). While increasing quantity of CB in composites leads to constant increase in the mechanical properties. Scanning electron micrographs revealed presence of polymer-filler adhesion in case of biocomposites at 20 phr. [Pg.122]


See other pages where Hydrophobic adhesives is mentioned: [Pg.491]    [Pg.99]    [Pg.20]    [Pg.203]    [Pg.178]    [Pg.39]    [Pg.115]    [Pg.171]    [Pg.252]    [Pg.168]    [Pg.248]    [Pg.101]    [Pg.270]    [Pg.491]    [Pg.99]    [Pg.20]    [Pg.203]    [Pg.178]    [Pg.39]    [Pg.115]    [Pg.171]    [Pg.252]    [Pg.168]    [Pg.248]    [Pg.101]    [Pg.270]    [Pg.441]    [Pg.41]    [Pg.362]    [Pg.153]    [Pg.451]    [Pg.312]    [Pg.36]    [Pg.487]    [Pg.117]    [Pg.222]    [Pg.1880]    [Pg.197]    [Pg.421]    [Pg.700]    [Pg.1076]    [Pg.128]    [Pg.238]    [Pg.213]    [Pg.873]    [Pg.81]    [Pg.95]   
See also in sourсe #XX -- [ Pg.20 , Pg.109 , Pg.171 ]




SEARCH



Bacterial Adhesion Hydrophobic and Electrostatic Parameters

Hydrophobic cell walls, adhesion

Hydrophobic surfaces adhesion

Polymer adhesion surface hydrophobicity

© 2024 chempedia.info