Elastomers thermoplastic systems

Hot-melt thermoplastic elastomer systems (23. 24) are also effective coating materials. These materials are generally based on copolymers that are comprised of hard (crystalline or glassy) and rubbery (amorphous) segments contained in separate phases. The hard-phase regions form physical cross-links below their crystallization or vitrification temperature, and the system therefore has elastomeric properties. The moduli and low-temperature characteristics of these materials can be tailored to compare reasonably well with silicone rubbers at -40 C. However, they are limited in high-temperature applicability because of enhanced creep or flow due to softening. 

All four processes have certain advantages and disadvantages with regard to production procedure, economics, and final properties of the product. Practically no comparable data of systematic studies exist on the influence of mode of production of thermoplast-thermoplast and elastomer-elastomer systems. Systematic studies on individual systems only exist for thermoplast-elastomer systems (see further, below). 

CARBON BLACK-FILLED BLOCK COPOLYMER THERMOPLASTIC ELASTOMER SYSTEMS, 714 Fundamentals for Black-Filled Systems, 714 Experimental, 715 Rheology, 716... 

CARBON BLACK-FILLED BLOCK COPOLYMER THERMOPLASTIC ELASTOMER SYSTEMS... 

B. D. Nahloosky and G. A. Zimmerman, Thermoplastic Elastomers for S olid Propellant Binders, AERPL-TR-86-069, Aerojet Tactical Systems Co., Sacramento, Calif., Dec. 1986. 

Urethanes are processed as mbber-like elastomers, cast systems, or thermoplastic elastomers. The elastomer form is mixed and processed on conventional mbber mills and internal mixers, and can be compression, transfer, or injection molded. The Hquid prepolymers are cast using automatic metered casting machines, and the thermoplastic peUets are processed like aU thermoplastic materials on traditional plastic equipment. The unique property of the urethanes is ultrahigh abrasion resistance in moderately high Shore A (75—95) durometers. In addition, tear, tensUe, and resistance to many oUs is very high. The main deficiencies of the urethanes are their resistance to heat over 100°C and that shear and sliding abrasion tend to make the polymers soft and gummy. 

Thermoplastic elastomers are often multiphase compositions in which the phases are intimately dispersed. In many cases, the phases are chemically bonded by block or graft copolymerization. In others, a fine dispersion is apparentiy sufficient. In these multiphase systems, at least one phase consists of a material that is hard at room temperature but becomes fluid upon heating. Another phase consists of a softer material that is mbberlike at RT. A simple stmcture is an A—B—A block copolymer, where A is a hard phase and B an elastomer, eg, poly(styrene- -elastomer- -styrene). 

Properties such as low permanent set, low creep and low hysteresis are really measures of the efficiency of the heat fugitive network system. This is a complex function of the morphology. As a very general statement, the problem would seem to be less important with the harder grades of thermoplastic elastomer. 

Advanced Elastomer Systems Thermoplastic Elastomer Thermoplastic Rubber... 

Mehrabzadeh M. and Delfan N., Thermoplastic elastomers of butadiene-acrylonitrile copolymer and polyamide. VI. Dynamic crosslinking by different systems, J. Appl. Polym. Sci., 77, 2057, 2000. 

Macknight W.J. and Lundberg R.D., Research on ionomeric systems. Thermoplastic Elastomers (Holden, G., Legge N.R., Quirk R.P., and Schroeder H.E., eds.), Hanser Publishers, Munich, 1996. 

Cakmak M. and Wang M.D., Structure development in the tubular blown film of PP/EPDM thermoplastic elastomer, Antec 89, 47th Annual Tech. Conference of SPE, New York, May 1, 1989, 1756. Hashimoto T., Todo A., Itoi H., and Kawai H. Domain boundary structure of styrene-isoprene block copolymer films cast from solution. 2. Quantitative estimation of the interfacial thickness of lamellar microphase systems. Macromolecules, 10, 377, 1977. 

Al-Malaika, S. and Amir, E.J., Thermoplastic elastomers Part III—Ageing and mechanical properties of natural rubber-reclaimed rubber/polypropylene systems and their role as solid phase dispersants in polypropylene/polyethylene blends, Polym. Degrad. Stab., 26, 31, 1989. 

Improve both impact strength and rigidity of thermoplastics by using up the energy of crack propagation. Elastomers are prototypical toughening additives. Examples of high-polymeric impact modifier/thermoplastic matrix systems are EVA, CPE and MBS in PVC, EP(D)M and SBS in PA, and acrylic rubbers in polyesters. 

Recent work has focused on a variety of thermoplastic elastomers and modified thermoplastic polyimides based on the aminopropyl end functionality present in suitably equilibrated polydimethylsiloxanes. Characteristic of these are the urea linked materials described in references 22-25. The chemistry is summarized in Scheme 7. A characteristic stress-strain curve and dynamic mechanical behavior for the urea linked systems in provided in Figures 3 and 4. It was of interest to note that the ultimate properties of the soluble, processible, urea linked copolymers were equivalent to some of the best silica reinforced, chemically crosslinked, silicone rubber... 

Sequential addition of different monomer charges to a living anionic polymerization system is useful for producing well-defined block copolymers. Thermoplastic elastomers of the triblock type are the most important commercial application. For example, a styrene-isoprene-styrene triblock copolymer is synthesized by the sequence... 

ISO 23711 2003 Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers ISO 14910-1 1997 Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1 Designation system and basis for specifications ISO 14910-2 1997 Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2 Preparation of test specimens and determination of properties... 

Thermoplastic elastomers based on polyolefins (TPO) are blends of PE or PP wifh EPDM elastomers wherein the elastomer is often cross-linked using thermochemical systems. TPOs more suitable for medical producfs with no chemical residuals can be made using EB processing to cross-link the elastomer portion in such an elastomer-plastic blend. The thermoplastic governs the melt transition, and thus the extrusion properties of TPOs. The radiahon response of these materials is also governed by the choice of fhe thermoplastic. An example of an EB cured blend of EPDM and polyefhylene used is for fluid transmission tubing and electrical insulation. ... 

In solution, block copolymers display interesting colloidal and interfacial properties. They can be used as emulsifying agents in water-oil and oil-oil systems (6 ). In the later case, the oil phases are solid and they give rise to polymeric alloys (7.) or they are liquid and they allow the preparation of latexes in organic medium (8 ). However, the molecular structure of block copolymers based on polybutadiene PB (70 ) and polystyrene PS behave as thermoplastic elastomers when engaged in multiblock (PB-PS)n or triblock (PS-PB-PS) structures but never when implied in inverse triblock or diblock arrangements. Similarly the... 

The hydrogenation of the centre block of SBS copolymer produced oxidation stable thermoplastic elastomer. This product was commercialized by the Shell Development Company under the trade name of Kraton G. The field of thermoplastic elastomers based on styrene, 1-3-butadiene or isoprene has expanded so much in the last 10 years that the synthetic rubber chemist produced more of these polymers than the market could handle. However, the anionically prepared thermoplastic system is still the leader in this field, since it produced the best TPR s with the best physical properties. These TPR s can accommodate more filler, which reduces the cost. For example, the SBS Kraton type copolymer varies the monomer of the middle block to produce polyisoprene at various combinations, then, followed... 

Wise and Rocchio [32] have discussed the processing techniques for LOVA formulations which invariably depend on the type of binder. The polybutadiene-based formulations referred to as cured systems, are processed through a solventless process whereas formulations based on cellulose derivatives and thermoplastic elastomers as binders are processed by a solvent process similar to standard NC propellants. In conclusion, LOVA formulations offer unique propulsion systems for tanks with the potential to offer high energy and low vulnerability. 

This chapter introduces readers to the versatility of polyurethane polymers without spending too much time on the chemistry. The next chapter will discuss a more classical view of the molecule and how it is developed. Our point, however, is to present a functional view of this system. We have examined its physical characteristics, focusing our attention on the uniqueness of reticulated foams. All the chemical points we have made apply to all polyurethane polymers, whether they are open-celled foams, closed-cell foams, or thermoplastic elastomers. 

---