Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Sensor systems sampling system

With several springs, which function as torque gauges, and a number of spindles, viscosities can be measured up to 10 mPa-s with the Brookfield viscometer. The shear rates depend on the model and the sensor system they are ca 0.1 100 for the disk spindles, <132 for concentric cylinders, and <1500 for the cone—plate forlow viscosity samples. Viscosities at very low (ca 10 — 1 )) shear rates can be measured with the concentric... [Pg.188]

Application The zirconia oxygen sensor is widely used for combustion control processes and for air/fuel ratio regulation in internal combustion engines. The closed-end portion of the electrode tube is inserted into the exhaust gas stream. In the control of industrial combustion processes, no out stack sampling system is required. [Pg.1308]

The exposure of sensors in a by-pass stream (which can be valved off), is an alternative way of collecting monitoring data although correlation is required between the main-stream and the by-pass The use of a side-stream taken either side of a choke in the main-stream can provide a useful monitoring point. Traps where product streams can be condensed can offer alternative sampling systems. [Pg.1133]

NeSSI s driver is to simplify and standardize sample system design. There is also a huge opportunity to adapt the emerging class of lab-on-a-chip sensors to a miniature/modular smart manifold which could fundamentally change the way in which industry does process analysis. [Pg.22]

The simplest IR sensor would consist of a source, a sample interface and a detector. Although quite sensitive, such an arrangement would have no selectivity as any IR absorbing substance would cause an attenuation of the detected radiation. To get the selectivity that is a main driving force behind the application of IR systems, the radiation has to be spectrally analysed. This can be accomplished either by measurement at discrete wavelengths or, for multi-component sensors or samples containing (potentially) interfering substances, by full spectral analysis of the collected radiation. [Pg.141]

In parallel with improvements in chemical sensor performance, analytical science has also seen tremendous advances in the development of compact, portable analytical instruments. For example, lab-on-a-chip (LOAC) devices enable complex bench processes (sampling, reagent addition, temperature control, analysis of reaction products) to be incorporated into a compact, device format that can provide reliable analytical information within a controlled internal environment. LOAC devices typically incorporate pumps, valves, micromachined flow manifolds, reagents, sampling system, electronics and data processing, and communications. Clearly, they are much more complex than the simple chemo-sensor described above. In fact, chemosensors can be incorporated into LOAC devices as a selective sensor, which enables the sensor to be contained within the protective internal environment. Figure 5... [Pg.127]

Research has been done showing that rapid pressnre-driven LC analysis can be done with little solvent consumption, demonstrating this as a viable process analytical tool. Using electrokinetic nanoflow pumps LC can be miniaturized to the point of being a sensor system. Developments in terms of sampling to enable sampling directly from a process stream, to the separation channel on a chip are critical for the application of miniaturized process LC. The components (valves and pumps) required for hydrodynamic flow systems appear to be a current limitation to the fnll miniatnrization of LC separations. Detection systems have also evolved with electrochemical detection and refractive index detection systems providing increased sensitivity in miniaturized systems when compared to standard UV-vis detection or fluorescence, which may require precolumn derivatization. [Pg.535]

Figure 24.8 Experimental schematic of the multiplexed diode-laser sensor system used to measure CO, CO2, CH4, and H2O absorption by sampling hot combustion gases 1 ECDL 1.49-1.58 pm 2 optical isolator 3 — fiber coupler 4 — 1x2 fiber splitter 5 — etalon 6 — InGaAs detector 7 — DEB 1.65 pm 8 — 2 x 1 fiber combiner 9 optical fiber 10 fiber pitch 11 — concave mirror 12 — multipass... Figure 24.8 Experimental schematic of the multiplexed diode-laser sensor system used to measure CO, CO2, CH4, and H2O absorption by sampling hot combustion gases 1 ECDL 1.49-1.58 pm 2 optical isolator 3 — fiber coupler 4 — 1x2 fiber splitter 5 — etalon 6 — InGaAs detector 7 — DEB 1.65 pm 8 — 2 x 1 fiber combiner 9 optical fiber 10 fiber pitch 11 — concave mirror 12 — multipass...
Once a source of molecules exists, that source becomes the beginning of a pathway that leads, hopefully, to the sampling portion of a sensor system. That pathway may be tortuous it may be broad. There are a number of effects that alter the rate at which molecules become available to a detector. That rate, expressed as a concentration level per unit time within the medium where the detection... [Pg.76]

The sensor responses generated in a measurement result from physical and/ or chemical interactions between the sensors and the volatile compounds present in the headspace above the measured sample. By using a QMB sensor system with an array of six sensors, good discrimination between three hop varieties can be observed (Fig. 15.10a). In this example only 12 measurements per sample were analysed. The distance between clusters is reduced if the data set is increased to 50 measurements per sample (Fig. 15.10b). [Pg.331]

If, however, solid electrolytes remain stable when in direct contact with the reacting solid to be probed, direct in-situ determinations of /r,( ,0 are possible by spatially resolved emf measurements with miniaturized galvanic cells. Obviously, the response time of the sensor must be shorter than the characteristic time of the process to be investigated. Since the probing is confined to the contact area between sensor and sample surface, we cannot determine the component activities in the interior of a sample. This is in contrast to liquid systems where capillaries filled with a liquid electrolyte can be inserted. In order to equilibrate, the contacting sensor always perturbs the system to be measured. The perturbation capacity of a sensor and its individual response time are related to each other. However, the main limitation for the application of high-temperature solid emf sensors is their lack of chemical stability. [Pg.399]


See other pages where Sensor systems sampling system is mentioned: [Pg.159]    [Pg.24]    [Pg.41]    [Pg.427]    [Pg.254]    [Pg.127]    [Pg.223]    [Pg.497]    [Pg.501]    [Pg.522]    [Pg.587]    [Pg.55]    [Pg.60]    [Pg.432]    [Pg.279]    [Pg.255]    [Pg.167]    [Pg.158]    [Pg.146]    [Pg.204]    [Pg.110]    [Pg.537]    [Pg.235]    [Pg.262]    [Pg.6]    [Pg.17]    [Pg.95]    [Pg.152]    [Pg.135]    [Pg.175]    [Pg.196]    [Pg.98]    [Pg.251]    [Pg.106]    [Pg.114]    [Pg.297]    [Pg.62]    [Pg.814]    [Pg.1203]   
See also in sourсe #XX -- [ Pg.1193 ]




SEARCH



Sampling system

Sensor systems

Sensors sensor system

© 2024 chempedia.info