Regulations - compliance with

Occupational Safety and Health Administration (OSHA), the Environmental Protection Agency (EPA), and your state s rules and regulations. Compliance with all of these is necessary. 

Labeling compliance with these regulations is complex, and further labeling information is available (67,68). 

RCRA incinerator regulations include adrninistrative as weU as performance standards. Administrative standards include procedures for waste analysis, inspection of equipment, monitoring, and facihty security. Steps needed to meet adrninistrative standards are outlined ia the permit apphcation performance standards are demonstrated during a trial bum. Trial bum operating conditions are included in the permit to assure ongoing compliance with the performance standards. Performance standards include destmction and removal efficiency (DRE), particulate emissions limits, products of incomplete combustion emission limits, metal emission limits, and HCl and Cl emission limits (see Exhaust CONTROL, INDUSTRIAL). 

Historically the United States was a primary exporter of ion-exchange resin. As of 1994, the United States imports substantially more than it exports. Because compliance with tightening environmental regulations in the United States impacts on the cost of manufacture, offshore resin is most often lower in price. 

Table 2 Hsts some of the physical, toxicity, flammabiUty, and reactivity properties of common chemicals (10,13,42,45—51). Also given are some of the quantities specified for reporting spills and for compliance with legislated requirements. The OSHA regulations require that material safety data sheets (MSDS) be developed for all process materials, so that the ha2ard data can be communicated to employees (52). Characteristics of toxicity, flammabiUty, chemical iastabiUty, reactivity and reaction energy, operatiag coaditioas, and corrosive properties of constmction materials must all be considered ia analy2iag ha2ard poteatials of chemicals and chemical operations.

As part of TSCA, EPA can require the testing of any chemical if there is the possibiUty of an unreasonable risk to health or environment or if there is significant human or environmental exposure. If the substance poses an unreasonable risk, EPA can prohibit the manufacture, processing, or distribution of the substance limit the amount of the substance that can be manufactured, processed, or distributed prohibit a particular use for the substance limit the concentration of the substance during manufacture, processing, or distribution regulate disposal methods for the substance and require manufacturers to maintain records of process and to conduct tests to assure compliance with EPA rules. 

As of this writing (1997), researchers are exploring combinations of acids, additives, and catalysts to achieve a suitable economic finish. However, commercial appHcation of these finishes would require costs akin to that of DMDHEU as well as compliance with formaldehyde release levels by consumers, regulators, and the textile industry. Another possible impetus could be marketing considerations. Nevertheless, this work has sparked intense effort in the use of cross-linkers containing ester cross-links and has broadened the scope of cross-linker research. 

The handling of arsenic in the workplace should be in compliance with the Occupational Safety and Health Administration (OSHA) regulations the maximum permissible exposure limit for arsenic in the workplace is 10 p-g/m of air as deterrnined as an average over an 8-h period (33). 

Precaution should be taken to avoid accidental generation of arsine gas the maximum permitted exposure is 0.05 ppm in air per 8-h period five days per week (34). Disposal of arsenical products should be in compliance with Eederal and local government environmental regulations. 

Under the Comprehensive Environmental Response, Compensation, and LiabiHty Act (CERCLA)/RCRA regulations in effect at the end of 1986 bromine is regulated as a hazardous waste or material. Therefore, it must be disposed of in an approved hazardous waste faciHty in compliance with EPA and/or other appHcable local, state, and federal regulations and should be handled in a manner acceptable to good waste management practice. The reportable quantity is 45.4 kg for corrosivity (62). 

A deterrnination that carbon monoxide might be a metaboUte of methylene chloride in humans (33) suggests that unacceptable levels of carboxyhemoglobin would exist in the blood of persons exposed to methylene chloride vapors at concentrations greater than 500 ppm for extended periods of time. These conditions are rarely encountered in most industrial appHcations. However, as with any organic solvent, adequate ventilation should be provided to ensure compliance with all industrial and governmental regulations. 

In the United States, federal regulations require automobile manufacturers to certify that vehicles are ia compliance with exhaust emission standards when tested under specific test procedures. 

Introduction Review and audit processes are used in the chemical process industry to evaluate, examine, and verify the design of process equipment, operating procedures, and management systems. These processes assure compliance with company standards and guidelines as well as government regulations. Reviews and audits can encompass the areas of process and personnel safety, environmental and industrial hygiene protection, quality assurance, maintenance procedures, and so on. 

Will the contract address compliance with regulations ... 

The general purpose of an audit may be to determine if the toller has management systems and documented procedures in place to ensure process safety, environmental responsibility, product quality and traceability of materials. The need to audit could be to evaluate compliance with regulations or accordance with client requirements related to specific performance elements. A subjective rating system for ranking management systems audit results is often used. An example of one that might be appropriate is shown below ... 

Is the toller aware of any activities or operations that are not in compliance with any health or safety regulations ... 

Spill Prevention Control and Countermeasures Plan The document prepared in compliance with U.S. regulation Guidelines Eor The Preparation and Implementation of a Spill Prevention Control and Countermeasure Plan (SPCC) —EPA 40 CER part 112.7. 

Relative risk results show only the difference between the levels of safety of one or more cases of interest and a reference, or baseline, case. Relative risk estimates can be used (as can absolute estimates) to determine the most efficient way to improve safety at a facility. But, the use of relative risk estimates alone does little to help ensure that the most efficient way is safe enough unless one of the cases meets qualitative safety criteria (e.g., compliance with relevant codes, standards, and/or regulations consistency with current industry practice). 

All equipment should be used according to manufacturer s specifications and in compliance with all applicable regulations. 

Regulation of aircraft engine emissions has been made a national responsibility by law in the United States. The Administrator of the Environmental Protection Agency is responsible for establishing emission limits of aircraft engines, and the Secretary of Transportation is required to prescribe regulations to ensure compliance with these limits. 

---