Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Rated power

Figure 10-123 shows a typical power consumption in thrust bearings as a function of unit speed. Tne total power loss is usually about 0.8-10 percent of the total rate power of the unit. New vector lube bearings reduce the horsepower loss by as much as 30 percent. In large vertical pumps, thrust bearings take not only the load caused by... [Pg.945]

The influenee of sodium and organie eomponent on analytieal signal values of elements of interest is investigated. ICP parameters (flow rate, power and inner injeetor diameter) are optimized. [Pg.360]

Ratio of power through throttle Rated power required... [Pg.137]

Cut-oul wind speed is the maximum w ind speed beyond which the prime mover may overspeed above its permissible limits. As the structure and the blades are designed for a particular maximum speed, a wind speed higher than this may exceed their mechanical endurance and become unsafe. At this speed the brakes apply and the machine is disconnected from the grid. The cut-in and cut-out speeds define the wind speed limits within which the turbine will work safely through the generator. Rated wind speed is the speed at which the prime mover rotates at the rated negative slip and generates the rated power. [Pg.159]

The secondary windings should be capable of withstanding a rated power frequency, short-duration withstand voltage of 3 kV for I minute, (iii) Power frequency withstand test between sections... [Pg.494]

Rated power-frequency short-duration withstand voltage for volfoge test... [Pg.840]

Injection of Steam in the Combustor of the Gas Turbines Utilizing Present Dual Fuel Nozzles. Steam injection in the combustor has been commonly used for NO control as seen in Figure 2-43. The amount of steam, which can be added, is limited due to combustion concerns. This is limited to about 2-3% of the airflow. This would provide an additional 3-5% of the rated power. The dual fuel nozzles on many of the industrial turbines could easily be retrofitted to achieve the goal of steam injection. The steam would be produced using an HRSG. Multiple turbines could also be tied into one HRSG. [Pg.104]

The disadvantage of the quasi-resonant converter compared to the newer lossless snubber and active clamp techniques in addition to the basic PWM converters, is the voltage or current stresses placed upon the power components. The peak voltage or current values that exist within quasi-resonant converters can be two to three times higher than in PWM converters. This forces the designer to use higher-rated power switches and rectifiers which may not have as good conduction characteristics. [Pg.151]

The driver horsepower must be greater than the calculated (or value read from curves) input BHP to the shaft of the pump. The mechanical losses in the coupling, V-belt, gear-box, or other drive plus the losses in the driver must be accounted for in order that the driver rated power output will be sufficient to handle the pump. [Pg.201]

Cycles of concentration Blowdown/purge rate Power cost analysis Drift loss requirement Local authority requirements Discharge qualities Stmctural specifications Pack specifications... [Pg.539]

Latent heat High, depth Subcooling parameter Thermal conductivity Surface roughness Channel length Mass flow rate Power, number of sample Number of channels Pressure, precession limit Heat rate Heat flux... [Pg.99]

If the maximum flow-rate required is 20,000 kg/h, calculate the pump motor rating (power) needed. Take the pump efficiency as 70 per cent and allow for a pressure drop of 0.5 bar across the control valve and a loss of 10 velocity heads across the orifice. [Pg.241]

Manufacturer four Danfoss hermetic scroll compressor rated power of electric motor... [Pg.230]

The output of each power range channel is directly proportional to reactor power and typically covers a range from 0% to 125% of full power, but varies with each reactor. The output of each channel is displayed on a meter in terms of power level in percent of full rated power. The gain of each instrument is adjustable which provides a means for calibrating the output. This adjustment is normally determined by using a plant heat balance. Protective actions may be initiated by high power level on any two channels this is termed coincidence operation. [Pg.93]

Measure the peak of the Drain current waveform /LIM at rated power at 90VAC. [Pg.229]

A fuel cell system for automobile application is shown in Figure 1.5 [41]. At the rated power, the PEMFC stack operates at 2.5 atm. and 80°C to yield an overall system efficiency of 50% (based on lower heating value of hydrogen). Compressed hydrogen and air are humidified to 90% relative humidity at the stack temperature using process water and heat from the stack coolant. A lower system pressure is at part load and is determined by the operating map of the compressor-expander module. Process water is recovered from spent air in an inertial separator just downstream of the stack in a condenser and a demister at the turbine exhaust. [Pg.20]

Contact Rating Any combination of the switching voltage and current must not exceed the given rated power 10 W... [Pg.249]


See other pages where Rated power is mentioned: [Pg.360]    [Pg.360]    [Pg.582]    [Pg.582]    [Pg.99]    [Pg.2492]    [Pg.137]    [Pg.137]    [Pg.261]    [Pg.642]    [Pg.98]    [Pg.532]    [Pg.865]    [Pg.419]    [Pg.70]    [Pg.192]    [Pg.478]    [Pg.429]    [Pg.431]    [Pg.236]    [Pg.165]    [Pg.175]    [Pg.336]    [Pg.336]    [Pg.243]    [Pg.244]    [Pg.245]    [Pg.246]    [Pg.247]    [Pg.248]   
See also in sourсe #XX -- [ Pg.290 ]




SEARCH



A Expansion in powers of the shear rate and time

Bit Error Rate and Link Power Penalty

Energy Storage Options for Different ASD Power Ratings

Exercise 4.V Head, flow rate, and output of a hydroelectric power plant

Expansion in powers of the shear rate

Fluid Shear Rates, Impeller Pumping Capacity and Power Consumption

Input power, sputter rate

Marketing of max power rating

Nucleation obeying a power law with constant rate of interface advance (normal growth)

Power Consumption and Pumping Rate

Power Law Models and Elementary Rate Laws

Power Rate Prediction Instrumentation

Power law rate equation

Power law rate expressions

Power plants heat rate

Power plants steam rate

Power rate law

Power ratings

Power supplies peak current rating

Power-law dissociation rate

Purchasing power parity exchange rates

Rate equation, power approximation

Silent Chain Power Ratings

© 2024 chempedia.info